deos of this tutorial Series:
1. How to do CONCEPT DESIGN 3D Modelling in Rhino (Part 1 of 3); Beginner
https://www.youtube.com/watch?v=ZbMPZ...
2. How to do CONCEPT DESIGN: Material Textures in Rhino (Part 2 of 3)
https://www.youtube.com/watch?v=h8XRw...
3. How to do CONCEPT DESIGN -Create 3D Views in Rhino (Part 3 of 3);
https://www.youtube.com/watch?v=1RZMRwv8ub4
Feel Free to email us at Rhino4Arch@gmail.com for any help or information.…
and Ronnie of StudioMode and David Fano of DesignReform will also be attending.
RSVP has been closed on this event. Space is limited to 50 people. Please attend if you do RSVP.
Agenda -
12:00-1:00 Arrival, informal discussion
1:00 - 1:15 Introductions
1:15 - 2:00 Project presentation 1 (30 minutes + 15 min QA) - David Lee - Clemson - 3D pattern environments using volumetric proxies.
2:00 - 2:45 Project Presentation 2 (30 minutes + 15 min QA) - P. Casey Mahon - Organic Abstractions (30 minutes + 15 min QA)
2:45 - 3:45 David Rutten - New work in GH (30 min QA)
3:45 - 4:30 Sameer Kumar AIA - KPF - Project presentation 3 (30 minutes + 15 min QA)
4:30 - 5:15 Chris Wilkins - Clemson - Urban Renewal and parametric urban development studies in Grasshopper.
5:15 - 6:00 David Rutten - Scripting in GH (15 min QA)
After 6:00 conversations may move down the street for more discussion.
If you would like to present your project at the Cloud please email: scottd@mcneel.com…
requirements for making a valid 3D printable part. The basics are these:
1. Construct the curve forming the shape of the part (I use 6 points and an interpolated curve.)
2. Use this curve to make a Sweep1 surface
3. Extrude a small square along this same curve to make a make a square-shaped ridge and cap it. (I've tried triangles too.)
4. Make a circular Curve Array of 3 specifying the number of ribs you want. Be sure to use a rail curve that matches the sweep curve in 1.
5. Twist these ribs a specified # degrees, and then twist them the same number of degrees in the opposite direction.
6. Join 1 & 5 and you're done - almost. As I said, the top of the part will be flat, so I add a small circular cone to make it come to a nice point.
For 3D printing I had to give the basic surface thickness so I could control the amount of light transmitted through it, and also to eliminate naked edges, so Step 2 is actually more complicated than I indicated above. …
Added by Birk Binnard at 12:11pm on January 27, 2017
there is a gap there, so the pipes will not connect unless you make them larger and put rounded ends on them.
3. Most any 3D printer will have problems printing something as long and thin as your pipes are.
4. Attached is a screenshot of a section of you pipes (with flat ends to make them closed surfaces) after slicing with the Slic3r program. Except for that one outside corner, everything is connected. I'd suggest you try again with a layer height of 0.200 mm (or smaller) and a printer nozzle of 0.400 mm diameter (or smaller).
5. If you click on the Internalize option for the Crv component you will not need the Rhino file any longer - doing that loads the Rhino geometry into your GH file directly and saves it there.
6. Your pipes will need a lot of supports for 3D printing - but you already know that. Removing the support material from something that flimsy will be quite difficult. You would have better luck if you had a way to print them using a resin based printer - but these usually have smaller print volumes and are expensive.…
Added by Birk Binnard at 2:17am on November 21, 2017
the components seem to handle that like a list of lists, like a 2D array.
Say I send this 2x4 data to a curve divide, and it creates 10 points per each of 8 curves, then I feel like it should be outputting a sort of 3D array - 2 paths of 4 paths of 10 points, and I CAN still see the array structure in the param viewer. But I feel like it is outputting paths 20 paths of 5 point each. Is there are way to access the 2x10 stucture at this point?
(Manuel, I did just read your reply to my other post, and see that might be an answer to this, thanks)
Is everything pretty much handled as a 2D list of lists, and no 3D (no list of lists of lists)?
Are the tree logic components the key to getting the right 2D structure out of 3D (or deeper) structures?
Thanks!!!
Chris…
Added by Chris Wilkins at 9:57am on October 18, 2009
Rhino 3D Product Design Rendering Demo using Cycles Grasshopper Shaders. Studiorola provides Rhino 6 Rendering Training in Singapore. http://www.studiorola.com