EP output variables are to calculate outdoorAirEnergy?
Thank you very much!
Output variables on the Read EP Results component:[1] totalThermalEnergy=cooling+heating[2] thermalEnergyBalance=cooling (-)andheating (+)[3] cooling= Zone Ideal Loads Supply Air Total Cooling Energy [J](Hourly)=Zone Ideal Loads Supply Air Sensible Cooling Energy [J](Hourly)+ Zone Ideal Loads Supply Air Latent Cooling Energy [J](Hourly)[4] heating= Zone Ideal Loads Supply Air Total Heating Energy [J](Hourly)= Zone Ideal Loads Supply Air Sensible Heating Energy [J](Hourly) + Zone Ideal Loads Supply Air Latent Heating Energy [J](Hourly)[5] electricLight=Zone Lights Electric Energy [J](Hourly)[6] electricEquip=Electric Equipment Electric Energy [J](Hourly)[7] peopleGains=Zone People Total Heating Energy [J](Hourly)[8] totalSolarGain=Zone Windows Total Transmitted Solar Radiation Energy[9] infiltrationEnergy=Zone Infiltration Total Heat Gain Energy (+)andZone Infiltration Total Heat Loss Energy (-)[10] outdoorAirEnergy= ???[11] natVentEnergy=Zone Ventilation Total Heat Gain Energy (+)andZone Ventilation Total Heat Loss Energy (-)[12] operativeTemperature=Zone Operative Temperature[13] airTemperature=Zone Mean Air Temperature[14] meanRadTemperature=Zone Mean Radiant Temperature[15] relativeHumidity=Zone Air Relative Humidity[16] airFlowVolume=[infiltrationFlow] Zone Infiltration Standard Density Volume Flow Rate+[natVentFlow] Zone Ventilation Standard Density Volume Flow Rate+[mechSysAirFlow] Zone Mechanical Ventilation Standard Density Volume Flow Rate+[earthTubeFlow] Earth Tube Air Flow Volume[17] airHeatGainRate=[surfaceAirGain] Zone Air Heat Balance Surface Convection Rate+[systemAirGain] Zone Air Heat Balance System Air Transfer Rate
Output variables on the Read EP Surface Results component:[1] surfaceIndoorTemp= Surface Inside Face Temperature[2] surfaceOutdoorTemp=Surface Outside Face Temperature[3] surfaceEnergyFlow=[opaqueEnergyFlow] Surface Average Face Conduction Heat Transfer Energy+[glazEnergyFlow] Surface Window Heat Gain Energy[4] opaqueEnergyFlow =Surface Average Face Conduction Heat Transfer Energy[5] glazEnergyFlow= Surface Window Heat Gain Energy[6] windowTotalSolarEnergy=Surface Window Transmitted Solar Radiation Energy[7] windowBeamEnergy=Surface Window Transmitted Beam Solar Radiation Energy[8] windowDiffEnergy=Surface Window Transmitted Diffuse Solar Radiation Energy[9] windowTransmissivity=Surface Window System Solar Transmittance…
Rhino5 SR9. PT will not load unless you update.2- Download the PT installer (PanelingTools_2014_08_24_00.rhi) from: http://www.rhino3d.com/download/rhino/5.0/PanelingToolsV5/2- Double click the downloaded rhi file and follow the prompts to install.3- Next time you open Rhino and grasshopper, you should see the new version installed and loaded.4- The updated toolbars should be also installed. You might need to load using "ToolbarLayout" Rhino command.Documentation:There are comprehensive manuals available. Please make use of them.1- PT-Rhino: http://wiki.mcneel.com/_media/labs/panelingtools.pdf2- PT-GH: http://
wiki.mcneel.com/_media/labs/panelingtools4grasshopperprimer.pdf
New in this Release:--------------------
PT-Rhino:
1- All 2D and 3D Paneling commands, now pay attention to the attributes of the source module. Morphed geometry is no longer added to a new layer and is placed in the same layer as that of the source module(s).2- ptPanel3DCustomVariable with mean option: added support to use multiple start/end modules.3- ptPanel3DCustomVariable command with mean option: added support to use points as part of pattern.
4- Fixed history bugs to custom2d and custom3d variable commands.5- ptOffsetBorder: added bitmap and draft angle options.6- Added history support to ptGridSurface* commands.7- ptPlanarLips command is discontinued and is now replaced with the new ptTabs. The new command has "Distance" and "Recess" options to create tabs with a miter. It works with planar surfaces and polysurfaces.8- ptUnrollFaces: Many improvements and new options.9- Many other minor bug and crash fixes.PT-GH:1- Added anew component to morph variable 3D components using mean or tween method between matching curves, meshes or surfaces.2- Added the new ptOffsetGrid component of a grid.3- Updated the ptMorph2dVariable component to accept a tree structure.4- Fixed a few miscellaneous UI bugs and crashes.Feedback:As always, feedback is ve
ry much appreciated. Please post questions and reports to the following:1- Rhino discourse forum (http://discourse.mcneel.com/)2- PT forums (PT-Rhino: http://v5.rhino3d.com/group/panelingtools) and (PT-GH: http://www.grasshopper3d.com/group/panelingtools).3- Email tech (tech@mcneel.com) or reach me directly (rajaa@mcneel.com).Enjoy!Rajaa IssaRobert McNeel & Associates…
o it would cause troubles with unfolding and fabricating... that's why I used Extrude point component- it will give you similar result, but all surfaces are planar.. you can control extrusion direction with a tip point in rhino...
2)I changed tagging so every tube has 8 points form list A and 8 points from list B... first number of tag is a number of point within one tube... last number of the tag is order of tubes (I draw a little picture in GH, hope you'll understand)...I think original way of tagging wasn't really usefull.. but you can change tagging by yourself...
3) the definition is really messy, sorry about that, but it's just quite complicated task...
4)if you find some incorrect order of tagging, use the slider that controls Shift List component ... it will shift tagging..
5) if you won't be using this definition or find some better way, pleeeease don't tell me - I'll jump out the window :D ... it took me whole day to make it work :D
6)I can't guarantee you anything- I hope it works, but if not - at least I tried... so check everything (especially order of tags and points) twice before you fabricate it.. or print few tubes and make them paper first..
7)there is a part of original definition, that is not useful anymore.. I left it there, but you can delete it (I called it "UNUSED PARTS OF ORIGINAL FILE")
..good luck
Dimitri…
rà le strategie e le principali tecniche di FORM FINDING utilizzando il motore fisico KANGAROO integrato a plugin di analisi strutturale (MILLIPEDE e KARAMBA). Le tecniche saranno applicate a diversa scala: dall’architettura (modellazione di superfici e coperture a semplice compressione) al design del prodotto, dove la simulazione digitale sarà integrata a tecniche di refinement (WEAVERBIRD). Il workshop e rivolto a studenti e professionisti con conoscenze base di modellazione algoritmica con Grasshopper.
Tariffa EarlyBird entro il 28 marzo 2015
Main tutor: Arturo Tedeschi, Authorized Rhino Trainer, autore del primo manuale su Grasshopper “Architettura Parametrica”, di AAD_Algorithms Aided Design e co-director della AA Rome Visiting School (AA School London).
>scarica il pdf con tutte le informazioni: AAD GRASSHOPPER WORKSHOP SERIES…
visions). from what i can see from the image, this is generally a box form, with definable surfaces. I would start by creating an array of parallel lines along the length of the form.. maybe about 8 with an equal offset. what you can do with this is duplicate the lines then move this new set above the old set to give the form a general depth.
grab all of the lines and run a "rebuild" command, what you are doing with this is adding more points to the lines... lines are defined by two points you probably want to add about 6 to each line, this will allow you to have more control over what the line is doing, don’t add to many though because then the line becomes uncontrollable.
Now with the original set (the lower one) you can use the "points on" command found under the "Main 2" palette to access the points that define the geometry of the curve. manipulate these points for each curve into the form of the shape that you want... get used to this "points on" tool its extremely useful.
lastly grab all the lines in the lower set of line and run the "loft" command what this will do is create surface from the selected lines. then do the same for the top set.
just remember that in nurbs modeling al la this... that points define lines and lines define surfaces... and i guess you can also say that surfaces define polysurfaces.
good luck…
same simulation with two different settings, with _numOfCUPs_ set to 1 and again with it set to 10. I'm running it on a 6 core/12 thread CPU so I should have no problem handling 10 threads.
I've attached an Excel file with my results for how long it took with a single thread vs. how long each of threads took on the 10 thread run. What it amounts to is that with a single thread it took 51 minutes, and with the 10 thread option it took 47 minutes for it all to finish. With the latter the first 9 threads finished between 28-34 minutes which is a significant time savings over the single thread run, but the last thread still took almost as long and gave us only about an 8% time savings.
This is only one simple comparison and only one simulation type, but I've seen this same result happen over and over again over the past year or so with several simulations (annual, irradiance, illuminance,...). I also don't think it's necessarily a Honeybee problem, because even running the simulations myself by creating the octree mesh and running radiance and daysim from the command line I had the same issue where splitting a model up and running parallel simulations that were then recombined took just about as long as running it all in one thread. Add into this the time necessary to combine the different files at the end and your multithreading time savings become even less.
So is it me, my machine, radiance, bad karma?…
RESENTERS PETER ARBOUR seele KEITH BOSWELL Skidmore Owings & Merrill MARK E. DANNETTEL Thornton Thomasetti LISA IWAMOTO IwamotoScott JASON KELLY JOHNSONFuture Cities Lab/California College of the Arts HAO KO Gensler BILL KREYSLER Kreysler & Associates ANDREW KUDLESS Matsys/California College of the Arts CHRIS LASCH Aranda\Lasch ARNOLD LEE HOK MIC PATTERSON Enclos, Corp. M. MIN RA Front GEOFF ROSSI Element DENNIS SHELDEN Gehry Technologies ANN SMITH Cambridge Architectural MARCELLO SPINAP-A-T-T-E-R-N-S SANJEEV TANKHA Buro Happold BEN TRANEL Gensler PHIL WILLIAMS Webcor Builders & Consulting Group
DIGITAL FABRICATION WORKSHOPS
8 LU/HSW or 8 LU credits (depending upon workshop choice)
Friday, July 27th 2012 9:00 AM – 6:00 PMCalifornia College of the Arts San Francisco, California
PARAMETRIC ENVELOPES WITH GRASSHOPPERANDREW KUDLESS Matsys Design/California College of the Arts
COMPOSITE FACADES IN ARCHITECTUREBILL KREYSLER & JOSHUA ZABEL Kreysler & Associates
RESPONSIVE BUILDING FACADESJASON KELLY JOHNSON Future Cities Lab/California College of the Arts
SCRIPTED FACADESCHRIS LASCH Aranda/Lasch
PARAMETRIC FACADE TECTONICSKEVIN MCCLELLAN & ANDREW VRANA Digital Fabrication Alliance
BIM MODELING WITH REVIT/INTRO TO VASARIGERMAN APARICIO California College of the Arts & Autodesk Fellow
Facade technologies are developing at a more dynamic rate than almost any other issue related to construction today with an impact on performance, sustainability, materials, fabrication, design, delivery and much more. What was once thought impossible is now an everyday reality, and the future promises accelerating change.
Presented by Enclos and The Architect’s Newspaper, COLLABORATION will bring together in a two-day event, the industry, the profession, and the academy to explore the evolution and the issues surrounding today’s high tech building envelope through case studies and lectures presented by foremost
practitioners, as well as panel discussions, and workshops conducted by leaders in the AEC profession.
Aimed at architects, building owners and developers, general contractors, engineers, fabricators, material suppliers, educators, and students, the event’s panels and sessions address the transformative opportunities created by new technologies and resources. From using BIM for communicating effectively with fabricators, to energy modeling, to retrofitting practices and the latest design tools, the COLLABORATION conference offers an unprecedented opportunity to survey the possibilities of designing in the digital age.
Who Should Attend
Architects, designers, engineers, building owners, developers, and facade consultants interested in gaining increased understanding of cutting-edge building envelope technologies.…
quel que este interesado en aprender procesos Generativos y Paramétricos con Grasshopper para Rhino 5.
El Workshop esta organizado para que durante estos tres días, el estudiante domine los conceptos básicos y avanzados de Grasshopper.
Pre-requisitos:
Tener conocimiento del manejo de Rhino 5.
Cada estudiante debe traer su propio computador o portátil.
Rhino3D Colombia suministrara el Software de evaluación de Rhino 5 y Grasshopper.
Numero total de horas: 24
Fechas: Agosto 15, 16 y 17
Horas: de 8:00 am a 5 pm
Profesor: Andres Gonzalez, McNeel Miami
Lenguaje: Español / Ingles
Número de estudiantes: Máximo 8
Rhino Visual Tips 5.0 + SAVANNA3D
Se entregara un USB a cada participante con:
Rhino Visual Tips 5.0
Costos:
Antes del 2 de Agosto: 495.000 pesos Colombianos, después del 2 de Agosto, 595.000 pesos Colombianos.
Mayores informes:
www.Rhino3DColombia.com
Tel: 412 3015 Medellin, Colombia.
…
1 JUN to 31 DECBetween hours 1:00 to 24:00Current document units is in MetersConversion to Meters will be applied = 1.000[1 of 7] Writing simulation parameters...Ground temperature data contains monthly average temperatures at 3 different depths .5 meters (1st)2 meters (2nd)4meters (3rd)respectively[2 of 6] No context surfaces...[3 of 6] Writing geometry...[4 of 6] Writing materials and constructions...[5 of 7] Writing schedules...[6 of 7] Writing loads and ideal air system...[7 of 7] Writing outputs......... idf file is successfully written to : c:\ladybug\unnamed\EnergyPlus\unnamed.idf
Analysis is running!...c:\ladybug\unnamed\EnergyPlus\eplusout.csv......
Done! Read below for errors and warnings:
Program Version,EnergyPlus, Version 8.3.0-6d97d074ea, YMD=2015.05.24 11:32,IDD_Version 8.3.0
** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
** Warning ** Version: in IDF="'8.1.0'" not the same as expected="8.3"
************* Beginning Zone Sizing Calculations
** Severe ** GetSurfaceData: Some Outward Facing angles of subsurfaces differ significantly from base surface.
** ~~~ ** ...use Output:Diagnostics,DisplayExtraWarnings; to show more details on individual surfaces.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW3 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW3 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=EW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=EW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=0.9038)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=0.9038)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=16.0967)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=16.0967)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 6 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 7 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 8 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 9 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 5 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 6 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 7 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 8 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW6 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW6 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=EW0 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=EW0 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=1.4709)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=1.4709)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=15.6696)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=15.6696)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=FLOOR is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=FLOOR is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=CIELING is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=CIELING is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Warning ** ManageSizing: For a plant sizing run, there must be at least 1 Sizing:Plant object input. SimulationControl Plant Sizing option ignored.
************* Testing Individual Branch Integrity
************* All Branches passed integrity testing
************* Testing Individual Supply Air Path Integrity
************* All Supply Air Paths passed integrity testing
************* Testing Individual Return Air Path Integrity
************* All Return Air Paths passed integrity testing
************* No node connection errors were found.
************* Beginning Simulation
************* Simulation Error Summary *************
** Warning ** The following Report Variables were requested but not generated
** ~~~ ** because IDF did not contain these elements or misspelled variable name -- check .rdd file
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=CHILLER ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=BOILER HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=FAN ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE VENTILATION FAN ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE VENTILATION TOTAL HEAT LOSS ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE VENTILATION TOTAL HEAT GAIN ENERGY, Frequency=Hourly
************* There are 1 unused schedules in input.
************* There are 1 unused week schedules in input.
************* There are 3 unused day schedules in input.
************* Use Output:Diagnostics,DisplayUnusedSchedules; to see them.
************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
************* EnergyPlus Sizing Error Summary. During Sizing: 1 Warning; 49 Severe Errors.
************* EnergyPlus Completed Successfully-- 4 Warning; 49 Severe Errors; Elapsed Time=00hr 00min 4.59sec
Thanks Abraham.I really appreciate it.
Another thing ' I posted a discussion few days ago and got no replies.And this forum is the only 'Hope' for me..Can you quickly check it?thanks.
N
http://www.grasshopper3d.com/group/ladybug/forum/topics/free-form-external-wall-with-glazing-workflow?xg_source=activity
…
ns about them.
It's a direction for Kangaroo I very much intend to continue developing - and I am still getting to grips with the possibilities and experimenting with how different optimization and fairing forces work in combination with one another, so I would value your input and experience.
For those interested in some background reading material -
[1] http://www.cs.caltech.edu/~mmeyer/Research/FairMesh/implicitFairing.pdf
[2] http://mesh.brown.edu/taubin/pdfs/taubin-eg00star.pdf
[3] http://www.pmp-book.org/download/slides/Smoothing.pdf
[4] http://graphics.stanford.edu/courses/cs468-05-fall/slides/daniel_willmore_flow_fall_05.pdf
[5] http://www.evolute.at/technology/scientific-publications.html
[6] http://www.math.tu-berlin.de/~bobenko/recentpapers.html
[7] http://spacesymmetrystructure.wordpress.com/2011/05/18/pseudo-physical-materials/
[8] http://www.evolute.at/technology/scientific-publications/34.html
[9] http://www.evolute.at/software/forum/topic.html?id=18
At the moment the Laplacian smoothing is uniformly weighted, which tends to even out the edge lengths as well as smoothing the form, which is sometimes desirable, and sometimes not. It also tends to significantly shrink meshes when the edges are not fixed.
I plan to try some of the other weighting possibilities, such as Fujiwara or cotangent weighting (see [1] and [3]), as well as other fairing approaches, such as Taubin smoothing [2], Willmore flow[4], and so on. This also has applications in the simulation of bending of thin shells.
Planar quad panels are often desirable, but I'm finding that planarization forces alone are sometimes unstable, or cause undesirable crumpling, so need to be combined with some sort of fairing/smoothing, but the different types have quite different effects, and the balance is sometimes tricky.
There's also the whole issue of meshes which are circular (I posted a demo of circularization on the examples page), or conical (this one still isn't working quite right yet), and their relationship with principal curvature grids and placement of irregular vertices, all of which is rather different when the whole form is up for change, rather than having a fixed target surface [7].
I'm also trying to get to grips with ways of making surfaces of planar hexagons, which need to become concave in regions of negative Gaussian curvature (see this discussion)
and I hope to release soon a component for calculating CP meshes, as described in [8], which I think could have many exciting construction implications.
While there are a number of well developed smoothing algorithms, their main area of application so far seems to be in processing and improving 3D scan data, so using them in design in this way is somewhat new territory. There can be structural, fabrication or performance reasons for certain types of smoothness, but of course the aesthetic reasons are also often important, and I think there are some interesting discussions to be had here about the aesthetics of smoothness.
Anyway, that's enough rambling from me, hopefully something there triggers some discussion - I'm really keen to hear about how all of you envision these tools might be used and developed.
…