ow the steps of the successful run when step 1.2 is bypassed (note that the and OpenFOAM session is open in the background while running the Butterfly demo file):
1. create wind tunnel, and use different parameters of (4,4) for _globalRefLevel_ as suggested by Theodoro in this post
2. run blockMesh:
3. run snappyHexMesh:
4. run checkMesh:
5. connect the case from checkMesh to simpleFOAM and run the simulation:
6. the simulation converged at 1865 iteration, but the results visualization part has some problem:
7. so I revised this part according to suggestions from Hagit:
8. and the results can be visualized for P and U values:
The GH file used for the successful run shown above is attached here.
Now, the following is the error I got when the case from the update fvScheme component is used for simpleFOAM simulation:
the warning message on the simpleFOAM component is:
1. Solution exception: --> OpenFOAM command Failed!#0 Foam::error::printStack(Foam::Ostream&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #1 Foam::sigFpe::sigHandler(int) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #2 ? in "/lib64/libc.so.6" #3 double Foam::sumProd<double>(Foam::UList<double> const&, Foam::UList<double> const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #4 Foam::PCG::solve(Foam::Field<double>&, Foam::Field<double> const&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #5 Foam::GAMGSolver::solveCoarsestLevel(Foam::Field<double>&, Foam::Field<double> const&) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #6 Foam::GAMGSolver::Vcycle(Foam::PtrList<Foam::lduMatrix::smoother> const&, Foam::Field<double>&, Foam::Field<double> const&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::PtrList<Foam::Field<double> >&, Foam::PtrList<Foam::Field<double> >&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #7 Foam::GAMGSolver::solve(Foam::Field<double>&, Foam::Field<double> const&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #8 Foam::fvMatrix<double>::solveSegregated(Foam::dictionary const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libfiniteVolume.so" #9 Foam::fvMatrix<double>::solve(Foam::dictionary const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #10 Foam::fvMatrix<double>::solve() in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #11 ? in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #12 __libc_start_main in "/lib64/libc.so.6" #13 ? in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam"
The error message from the readMe! output node is attached below as a text file.
Hope you can kindly advise what the important steps or parameters I might have missed here. I assume it might be related to OpenFOAM rather than with the Butterfly workflow...
Thank you very much!
- Ji
…
sando las nuevas tecnologías de la información en la arquitectura para la gestión del conocimiento de sistemas que desarrollen estructuras sustentables, desde los procesos de diseño generativos o algorítmicos. Donde se contempla la P.O.O. (programación orientada a objetos) como nuevo lenguaje de expresión para el arquitecto-diseñador en el siglo XXI.Los talleres están pensados para sigan un hilo conductual en el que al mismo tiempo que se enseña se investiga y experimenta. Por primera vez se contará con diversos miembros de SEED como docentes de forma presencial y por video conferencia, logrando de esta forma acercar a los especialistas que se encuentran en Europa a los asistentes de los talleres sin encarecer los costos.+info:http://www.studioseed.net/ adn-methodology/
Los talleres están dirigidos a personas que tengan o quieran conseguir un perfil alto de innovación, creatividad, flexibilidad: profesionales con actividades de dirección, gerencia, proyectistas, investigadores, así como a estudiantes a partir de 5to semestre en adelante. Cada taller abarca perfiles diversos de profesionales, mientras unos están más orientados a directivos y gerencias, otros más a proyectistas.
LOS TALLERES:FAB DIG I / ITESM – CEM / Estado de México / 20 hrs / 8 – 11 al de diciembre 2011 (En este taller no se aplican descuentos ni becas)PARAMETRIC GREEN HOUSING / Colegio de Arquitectos del estado de Jalisco (Por confirmar Sede) / Guadalajara / 20h + 5h proyecto / 30 enero 2012 al 4 de diciembre 2012FAB DIG II / ITESM – CEM / Estado de México / 30h + 5h proyecto / 8 a 12 febrero 2012TERCERA REVOLUCIÓN INDUSTRIAL: TIC`s + SOSTENIBILIDAD. Procesos y paradigmas emergentes / Querétaro / 20 hrs / 15 al 18 de febrero 2012INTRODUCCIÓN AL DISEÑO GENERATIVO / UAM-azc / DF / 8hrs / 13, 14 de enero (Costo representativo $650, máximo 40 personas, mínimo 15 personas)INTRODUCCIÓN A: SCRIPTING CON GRASSHOPPER ( Python) Y PLUGINS / Estudio SEED México / Estado de México / 30 hrs / 23, 24, 25 febrero y 1,2, 3 de marzo 2012…
Added by SEED studio at 3:30am on November 24, 2011
ly 26-27-28-29 (digital fabrication)
The third edition of digitalMed Workshop is structured as a design laboratory. Participants will learn the challenging process of producing ideas, projects and research analysis that are to be developed through specific software and concepts that emerge through the use of mapping, parametric design and digital fabrication.
The workshop will take place in the city of Salerno (Italy) and it will last 11 days structured into 3 intensive weekends: July 13-14-15 (mapping); July 19-20-21-22 (parametric design); July 26-27-28-29 (digital fabrication).
Goals and Objectives:
We aim to make clear the theoretical and technical knowledge in the approach to parametric and generative design and digital fabrication. (From collection and data management, to the manner in which these inform the geometries, to the fabrication of prototypes.)
Participants will also have the opportunity to practice the new knowledge gained in the design laboratory through project work.
Project Theme:
"Urban Field" Identify, study and analyze the system of public spaces in the urban area of the city of Salerno.
Connection, mutation, generation and evolution are the themes to be followed in project work.
Brief Description of Topics:
- Mapping. Our reality, in all its forms, has studied through concepts of the theory of Complex Systems. The techniques that will be used to study events and places of reality, will work for the management, manipulation and visualization of data and information. These will form the basis for project management and driven geometry, conducted during the second phase of the workshop.
- Parametric Design. Introduction to Rhino* and Grasshopper. Specifically, we will explain the concepts with which to work with the software of parametric design and how they function. Through these tools, we will arrive at the definition of systems of mathematical and / or geometrical relationships that are able to generate and govern patterns, shapes and objects that will inform the final design.
- Digital Fabrication. In this phase, participants of the workshop are organized into working groups. Participants have access to materials and conceptual apparatus that will take them directly to the fabrication of the geometries of the project, with the use of software CAD / CAM interface and the use of machines for the digital fabrication.
The DigitalMed workshop is organized by Nomad AREA (Academy of Research & Training in topics of Contemporary Architecture), in collaboration with the City of Salerno, the Order of Architects Province of Salerno and the National Institute of Architecture In / Arch - Campania.
Interested parties may download the Notice of Competition at the address www.digitalmedworkshop.com and fill the pre-registration no later than July 10th 2012.
PRESS OFFICE
Dr. Francesca Luciano
328 61 20 830
fra_luciano@libero.it
For information or subscriptions:
e-mail: info@digitalmedworkshop.com - tel: 089 463126 - 3391542980 …
he "return" is comment out as shown below?
After restarting Rhino and Grasshopper, I opened the outdoors_airflow demo file, and the first step of creating the case file is ok:
Then the blockMesh component gives the following error: seems I have to manually start OF first..
so, as the error message suggested, I open OF by Start_OF.bat:
Then come back to the blockMesh component, now it can be executed while the OF command line window is also openning:
... and the blockMesh finished successfully:
... so I proceeded to run snappyHexMesh, checkMesh and update fvScheme:
... up to the simpleFoam component, I got the error again:
The warning message is:
1. Solution exception: --> OpenFOAM command Failed!#0 Foam::error::printStack(Foam::Ostream&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #1 Foam::sigFpe::sigHandler(int) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #2 ? in "/lib64/libc.so.6" #3 double Foam::sumProd<double>(Foam::UList<double> const&, Foam::UList<double> const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #4 Foam::PCG::solve(Foam::Field<double>&, Foam::Field<double> const&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #5 Foam::GAMGSolver::solveCoarsestLevel(Foam::Field<double>&, Foam::Field<double> const&) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #6 Foam::GAMGSolver::Vcycle(Foam::PtrList<Foam::lduMatrix::smoother> const&, Foam::Field<double>&, Foam::Field<double> const&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::PtrList<Foam::Field<double> >&, Foam::PtrList<Foam::Field<double> >&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #7 Foam::GAMGSolver::solve(Foam::Field<double>&, Foam::Field<double> const&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #8 Foam::fvMatrix<double>::solveSegregated(Foam::dictionary const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libfiniteVolume.so" #9 Foam::fvMatrix<double>::solve(Foam::dictionary const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #10 Foam::fvMatrix<double>::solve() in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #11 ? in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #12 __libc_start_main in "/lib64/libc.so.6" #13 ? in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam"
... and the command lines in the readMe! output are pretty long and it is saved in the text file attached here.
So, my questions are:
1. why I have to manually start OF first before I can use the blockMesh component? Should butterfly automatically start OF?
2. what might be the cause of the unsuccessful run of simpleFoam in the end?
Hope you can kindly advise! Thank you!
- Ji
…
A repository of generic or complex examples.
Example 01: Attractor Values
ND_001_AttractorValues.gh
Example 02: Curve Values
ND_002_CurveValues.gh
Example 03: Point Attractor
ND_003_PointAttract
teraction for its Correlations cycle, AA Athens Visiting School scales up its design intentions in order to investigate links among discrete individual architectural systems in its 2013 version, Recharged.
Recharged with interconnectivity on different levels, the theme of investigation will revolve around the design of semi-independent design prototypes acting together to form elaborate unified results. The driving force in Cipher City: Recharged is the synergistic effect behind complex form-making systems where interactive design patterns arise out of a multiplicity of relatively simple rules.
In collaboration with the National Technical University of Athens, Cipher City: Recharged will explore participatory design and active engagement modeling and will continue building novel prototypes upon horizontal planes.
As in 2012, the design agendas of AA Athens and AA Istanbul Visiting Schools will directly create feedback on one another, allowing participation in either one or both Programmes.
Discounts
The AA offers several discount options for participants wishing to apply as a group or participants wishing to apply for both AA Istanbul and AA Athens Visiting Schools:
1. Standard application
The AA Visiting School requires a fee of £695 per participant, which includes a £60 Visiting Membership. If you are already a member, the total fee will be reduced automatically by £60 by the online payment system. Fees are non refundable.
2. Group registration
For group applications, there will be a range of discounts depending on the number of people in the group. The discounted fee will be applied to each individual in the group.
Type A. 3-6 people group: £60 (AA Membership fee) + 635*0.75 = £536.25 (25 %) Type B. 6-15 people group: £60 + 635*0.70 = £504.5 (30%) Type C. more than 15 people group: £60 + 635*0.65 = £472.75 (35%)
3. Participants attending both AA Istanbul and AA Athens | 40% discount
For people wishing to attend both AA Istanbul 2013 and AA Athens 2013, a discount of 40% will be made for each participant. (The participant will pay the £60 membership fee only once.)
£60 (AA Membership fee) + (635*0.60)*2 = £822
For more information in discounts, please visit:
http://ai.aaschool.ac.uk/athens/portfolio/discounts-2013/
Applications
The deadline for applications is 11 March 2013. A portfolio or CV is not required, only the online application form and payment. The online application can be reached from:
http://www.aaschool.ac.uk/STUDY/VISITING/athens…
Added by elif erdine at 12:33pm on December 13, 2012
t file** - ply file with just x,y,z locations. I got it from a 3d scanner. Here is how first few lines of file looks like - ply format ascii 1.0 comment VCGLIB generated element vertex 6183 property float x property float y property float z end_header -32.3271 -43.9859 11.5124 -32.0631 -43.983 11.4945 12.9266 -44.4913 28.2031 13.1701 -44.4918 28.2568 13.4138 -44.4892 28.2531 13.6581 -44.4834 28.1941 13.9012 -44.4851 28.2684 ... ... ... In case you need the data - please email me on **nisha.m234@gmail.com**. **Algorithm:** I am trying to find principal curvatures for extracting the ridges and valleys. The steps I am following is: 1. Take a point x 2. Find its k nearest neighbors. I used k from 3 to 20. 3. average the k nearest neighbors => gives (_x, _y, _z) 4. compute covariance matrix 5. Now I take eigen values and eigen vectors of this covariance matrix 6. I get u, v and n here from eigen vectors. u is a vector corresponding to largest eigen value v corresponding to 2nd largest n is 3rd smallest vector corresponding to smallest eigen value 7. Then for transforming the point(x,y,z) I compute matrix T T = [ui ] [u ] [x - _x] [vi ] = [v ] x [y - _y] [ni ] [n ] [z - _z] 8. for each i of the k nearest neighbors:<br> [ n1 ] [u1*u1 u1*v1 v1*v1] [ a ]<br> [ n2 ] = [u2*u2 u2*v2 v2*v2] [ b ] <br> [... ] [ ... ... ... ] [ c ] <br> [ nk ] [uk*uk uk*vk vk*vk]<br> Solve this for a, b and c with least squares 9. this equations will give me a,b,c 10. now I compute eigen values of matrix [a b b a ] 11. This will give me 2 eigen values. one is Kmin and another Kmax. **My Problem:** The output is no where close to finding the correct Ridges and Valleys. I am totally Stuck and frustrated. I am not sure where exactly I am getting it wrong. I think the normal's are not computed correctly. But I am not sure. I am very new to graphics programming and so this maths, normals, shaders go way above my head. Any help will be appreciated. **PLEASE PLEASE HELP!!** **Resources:** I am using Visual Studio 2010 + Eigen Library + ANN Library. **Other Options used** I tried using MeshLab. I used ball pivoting triangles remeshing in MeshLab and then applied the polkadot3d shader. If correctly identifies the ridges and valleys. But I am not able to code it. **My Function:** //the function outputs to ply file void getEigen() { int nPts; // actual number of data points ANNpointArray dataPts; // data points ANNpoint queryPt; // query point ANNidxArray nnIdx;// near neighbor indices ANNdistArray dists; // near neighbor distances ANNkd_tree* kdTree; // search structure //for k = 25 and esp = 2, seems to got few ridges queryPt = annAllocPt(dim); // allocate query point dataPts = annAllocPts(maxPts, dim); // allocate data points nnIdx = new ANNidx[k]; // allocate near neigh indices dists = new ANNdist[k]; // allocate near neighbor dists nPts = 0; // read data points ifstream dataStream; dataStream.open(inputFile, ios::in);// open data file dataIn = &dataStream; ifstream queryStream; queryStream.open("input/query.
pts", ios::in);// open data file queryIn = &queryStream; while (nPts < maxPts && readPt(*dataIn, dataPts[nPts])) nPts++; kdTree = new ANNkd_tree( // build search structure dataPts, // the data points nPts, // number of points dim); // dimension of space while (readPt(*queryIn, queryPt)) // read query points { kdTree->annkSearch( // search queryPt, // query point k, // number of near neighbors nnIdx, // nearest neighbors (returned) dists, // distance (returned) eps); // error bound double x = queryPt[0]; double y = queryPt[1]; double z = queryPt[2]; double _x = 0.0; double _y = 0.0; double _z = 0.0; #pragma region Compute covariance matrix for (int i = 0; i < k; i++) { _x += dataPts[nnIdx[i]][0]; _y += dataPts[nnIdx[i]][1]; _z += dataPts[nnIdx[i]][2]; } _x = _x/k; _y = _y/k; _z = _z/k; double A[3][3] = {0,0,0,0,0,0,0,0,0}; for (int i = 0; i < k; i++) { double X = dataPts[nnIdx[i]][0]; double Y = dataPts[nnIdx[i]][1]; double Z = dataPts[nnIdx[i]][2]; A[0][0] += (X-_x) * (X-_x); A[0][1] += (X-_x) * (Y-_y); A[0][2] += (X-_x) * (Z-_z); A[1][0] += (Y-_y) * (X-_x); A[1][1] += (Y-_y) * (Y-_y); A[1][2] += (Y-_y) * (Z-_z); A[2][0] += (Z-_z) * (X-_x); A[2][1] += (Z-_z) * (Y-_y); A[2][2] += (Z-_z) * (Z-_z); } MatrixXd C(3,3); C <<A[0][0]/k, A[0][1]/k, A[0][2]/k, A[1][0]/k, A[1][1]/k, A[1][2]/k, A[2][0]/k, A[2][1]/k, A[2][2]/k; #pragma endregion EigenSolver<MatrixXd> es(C); MatrixXd Eval = es.eigenvalues().real().asDiagonal(); MatrixXd Evec = es.eigenvectors().real(); MatrixXd u,v,n; double a = Eval.row(0).col(0).value(); double b = Eval.row(1).col(1).value(); double c = Eval.row(2).col(2).value(); #pragma region SET U V N if(a>b && a>c) { u = Evec.row(0); if(b>c) { v = Eval.row(1); n = Eval.row(2);} else { v = Eval.row(2); n = Eval.row(1);} } else if(b>a && b>c) { u = Evec.row(1); if(a>c) { v = Eval.row(0); n = Eval.row(2);} else { v = Eval.row(2); n = Eval.row(0);} } else { u = Eval.row(2); if(a>b) { v = Eval.row(0); n = Eval.row(1);} else { v = Eval.row(1); n = Eval.row(0);} } #pragma endregion MatrixXd O(3,3); O <<u, v, n; MatrixXd UV(k,3); VectorXd N(k,1); for( int i=0; i<k; i++) { double x = dataPts[nnIdx[i]][0];; double y = dataPts[nnIdx[i]][1];; double z = dataPts[nnIdx[i]][2];; MatrixXd X(3,1); X << x-_x, y-_y, z-_z; MatrixXd T = O * X; double ui = T.row(0).col(0).value(); double vi = T.row(1).col(0).value(); double ni = T.row(2).col(0).value(); UV.row(i) << ui * ui, ui * vi, vi * vi; N.row(i) << ni; } Vector3d S = UV.colPivHouseholderQr().solve(N); MatrixXd II(2,2); II << S.row(0).value(), S.row(1).value(), S.row(1).value(), S.row(2).value(); EigenSolver<MatrixXd> es2(II); MatrixXd Eval2 = es2.eigenvalues().real().asDiagonal(); MatrixXd Evec2 = es2.eigenvectors().real(); double kmin, kmax; if(Eval2.row(0).col(0).value() < Eval2.row(1).col(1).value()) { kmin = Eval2.row(0).col(0).value(); kmax = Eval2.row(1).col(1).value(); } else { kmax = Eval2.row(0).col(0).value(); kmin = Eval2.row(1).col(1).value(); } double thresh = 0.0020078; if (kmin < thresh && kmax > thresh ) cout << x << " " << y << " " << z << " " << 255 << " " << 0 << " " << 0 << endl; else cout << x << " " << y << " " << z << " " << 255 << " " << 255 << " " << 255 << endl; } delete [] nnIdx; delete [] dists; delete kdTree; annClose(); } Thanks, NISHA…
1 JUN to 31 DECBetween hours 1:00 to 24:00Current document units is in MetersConversion to Meters will be applied = 1.000[1 of 7] Writing simulation parameters...Ground temperature data contains monthly average temperatures at 3 different depths .5 meters (1st)2 meters (2nd)4meters (3rd)respectively[2 of 6] No context surfaces...[3 of 6] Writing geometry...[4 of 6] Writing materials and constructions...[5 of 7] Writing schedules...[6 of 7] Writing loads and ideal air system...[7 of 7] Writing outputs......... idf file is successfully written to : c:\ladybug\unnamed\EnergyPlus\unnamed.idf
Analysis is running!...c:\ladybug\unnamed\EnergyPlus\eplusout.csv......
Done! Read below for errors and warnings:
Program Version,EnergyPlus, Version 8.3.0-6d97d074ea, YMD=2015.05.24 11:32,IDD_Version 8.3.0
** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
** Warning ** Version: in IDF="'8.1.0'" not the same as expected="8.3"
************* Beginning Zone Sizing Calculations
** Severe ** GetSurfaceData: Some Outward Facing angles of subsurfaces differ significantly from base surface.
** ~~~ ** ...use Output:Diagnostics,DisplayExtraWarnings; to show more details on individual surfaces.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW3 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW3 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=EW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=EW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=0.9038)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=0.9038)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=16.0967)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=16.0967)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 6 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 7 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 8 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 9 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 5 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 6 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 7 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 8 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW6 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW6 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=EW0 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=EW0 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=1.4709)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=1.4709)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=15.6696)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=15.6696)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=FLOOR is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=FLOOR is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=CIELING is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=CIELING is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Warning ** ManageSizing: For a plant sizing run, there must be at least 1 Sizing:Plant object input. SimulationControl Plant Sizing option ignored.
************* Testing Individual Branch Integrity
************* All Branches passed integrity testing
************* Testing Individual Supply Air Path Integrity
************* All Supply Air Paths passed integrity testing
************* Testing Individual Return Air Path Integrity
************* All Return Air Paths passed integrity testing
************* No node connection errors were found.
************* Beginning Simulation
************* Simulation Error Summary *************
** Warning ** The following Report Variables were requested but not generated
** ~~~ ** because IDF did not contain these elements or misspelled variable name -- check .rdd file
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=CHILLER ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=BOILER HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=FAN ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE VENTILATION FAN ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE VENTILATION TOTAL HEAT LOSS ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE VENTILATION TOTAL HEAT GAIN ENERGY, Frequency=Hourly
************* There are 1 unused schedules in input.
************* There are 1 unused week schedules in input.
************* There are 3 unused day schedules in input.
************* Use Output:Diagnostics,DisplayUnusedSchedules; to see them.
************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
************* EnergyPlus Sizing Error Summary. During Sizing: 1 Warning; 49 Severe Errors.
************* EnergyPlus Completed Successfully-- 4 Warning; 49 Severe Errors; Elapsed Time=00hr 00min 4.59sec
Thanks Abraham.I really appreciate it.
Another thing ' I posted a discussion few days ago and got no replies.And this forum is the only 'Hope' for me..Can you quickly check it?thanks.
N
http://www.grasshopper3d.com/group/ladybug/forum/topics/free-form-external-wall-with-glazing-workflow?xg_source=activity
…
giornata inaugurale sarà dedicata alla free-lecture introduttiva finalizzata alla realizzazione di un modello d'architettura complesso attraverso l'utilizzo di comandi e tecniche avanzate di rappresentazione con Grasshopper (plug-in parametrica di Rhinoceros) e 3dsMax. Sarà illustrato inoltre il potenziale di V-ray per 3dsMax realizzando un rendering concettuale. Durante il mini-corso dell' openDAY verranno mostrate le caratteristiche e le potenzialità degli strumenti per far luce sui nuovi valori assunti dalla modellazione 3D. La modellazione 3D sta interessando un pubblico sempre più vasto inserendosi in una nuova fase di ampia disponibilità per conoscenze, software, hardware di prototipazione e modelli. Pur mantenendo tutti i suoi valori già noti la questione si è talmente ampliata fino ad interessare norme giuridiche (diritti sui modelli ,concorrenza con offerte di servizi apparentemente simili, informazioni deformate e onfusione nei media) Makers University[http://www.makersuniversity.com], in collaborazione con parametricart, vi propone un punto di vista ampio e sintetico su queste tematiche.
Al termine della free-lecture, sarà illustrata l'offerta formativa [CLICCA QUI] di parametricart riferita ai corsi che si terranno nei mesi di Gennaio e Febbraio 2013 inseriti all'interno della più ampia programmazione della Makers University. SONO PREVISTE TARIFFE PROMOZIONALI PER COLORO CHE SI ISCRIVERANNO AI CORSI durante l'OpenDAY.
La lezione e la presentazione si terranno nel nuovo spazio co-working il PEDONE.
PROGRAMMAZIONE
- I temi della Makers University [Leo Sorge];
- Modellazione della parametricTower (concept di architettura complessa) utilizzando Grasshopper, applicativo per la modellazione parametrica [VIDEO] [Michele Calvano];
- Modellazione di una copertura reticolare 3D a completamento della parametricTower con 3dsMax utilizzando tecniche di modellazione mesh complesse [Wissam Wahbeh];
- Rendering con V-ray per 3dsMax illustrando la nuova interfaccia nodale [Wissam Wahbeh].
- Question Time per chiarimenti sugli argomenti illustrati.
COME
L'openDAY sarà aperto a tutti gli interessati,completamente gratuito e sarà replicato in tre sessioni di uguali contenuti organizzate nei seguenti orari:
Sessione [1] 11,30 - 13,30
Sessione [2] 15,30 - 17,30
Sessione [3] 17,30 - 19,30
Per necessità di organizzazione è importante la prenotazione all'evento utilizzando il form in fondo alla pagina specificando nella stringa apposita, il nome dell'evento e la sessione (es. open day sessione 1) oltre agli altri dati richiesti.…
lass BrepDeform Inherits GH_Component Public Reslist As New List(Of String) Public Sub New() MyBase.New("BrepDeform", "Deform", _ "移动物件的控制点" & vbCrLf & "(Move the control Point to change a object)", "SEG", "Modify")
End Sub Public Overrides ReadOnly Property ComponentGuid As System.Guid Get Return New Guid("8226e0ea-ed6b-47c2-8a24-244f044152d8") End Get End Property Protected Overrides ReadOnly Property Internal_Icon_24x24() As System.Drawing.Bitmap Get Return My.Resources.SEG_BrepDeform End Get End Property Protected Overrides Sub RegisterInputParams(ByVal pManager As GH_Component.GH_InputParamManager) ' pManager.AddTextParameter("Guid", "Id", "将要被替换的犀牛物件" & vbCrLf & "(RhinoObjects that will be replaced)", GH_ParamAccess.item) 'Dim guidParam As New Param_Guid pManager.AddParameter(New Param_Guid, "Guid", "Id", "将要被替换的犀牛物件" & vbCrLf & "(RhinoObjects that will be replaced)", GH_ParamAccess.item) pManager.AddPointParameter("ControlPoint3d", "C", "控制点的位置" & vbCrLf & "(Control Point's location)", GH_ParamAccess.item) pManager.AddPointParameter("NewPoint3d", "P", "新控制点的位置" & vbCrLf & "(New Control Point's location)", GH_ParamAccess.item) pManager.AddNumberParameter("Tolerace", "T", "输入点与物件实际控制点对比的精度" & vbCrLf & "(Tolerace for the Control Point match)", GH_ParamAccess.item, 0.1)
pManager.AddBooleanParameter("BlMove", "M", "如果是True则进行移动" & vbCrLf & "(If true Perform the Move)", GH_ParamAccess.item, False)
End Sub Protected Overrides Sub RegisterOutputParams(ByVal pManager As Kernel.GH_Component.GH_OutputParamManager) pManager.AddTextParameter("Result", "RG", "结果列表" & vbCrLf & "(Result)", GH_ParamAccess.list) End Sub Public Overrides ReadOnly Property Exposure As GH_Exposure Get Return GH_Exposure.primary End Get End Property
Protected Overrides Sub SolveInstance(ByVal DA As Kernel.IGH_DataAccess) If Banner.astrict.showmessage Then Return Dim Ids As Guid = Guid.Empty 'Dim Ids As String = String.Empty Dim tpt As Point3d = Point3d.Unset, opt As Point3d = Point3d.Unset Dim tolar As Double = 0.1 Dim blMove As Boolean = False If Not DA.GetData(0, Ids) Then Return If Not DA.GetData(1, opt) Then Return If Not DA.GetData(2, tpt) Then Return If Not DA.GetData(3, tolar) Then Return If Not DA.GetData(4, blMove) Then Return If Not blMove Then GoTo line1 Reslist.Add(Now & "_未替换!(Replace failed!)") Else Reslist.Clear() ' Grasshopper.Instances.ActiveCanvas.ModifiersEnabled = False End If
' rt.AddRange(docobjlist.Select(Function(geoobj As RhinoObject) GH_Convert.ObjRefToGeometry(New ObjRef(geoobj.Id)))) 'Private Checked(5) As Boolean, Namestr() As String = {"Point", "Curve", "Brep", "Mesh", "TextDot", "TextEntity"}
Try
Dim rh As RhinoDoc = Rhino.RhinoDoc.ActiveDoc Dim rhobj As RhinoObject = rh.Objects.Find(Ids) ' Dim rhobj As RhinoObject = rh.Objects.Find(New Guid(Ids))
Dim bobj As BrepObject = CType(rhobj, BrepObject) RhinoApp.RunScript("Cancel", False) RhinoApp.RunScript("Cancel", False) bobj.Select(True)
RhinoApp.RunScript("_SolidPtOn", False) Dim gobjs As GripObject() = bobj.GetGrips ' rh.Views.RedrawEnabled = False For Each grpobj As GripObject In gobjs
If grpobj.CurrentLocation.DistanceTo(opt) < tolar Then grpobj.Select(True) Dim CurrentPln As Plane = RhinoDoc.ActiveDoc.Views.ActiveView.ActiveViewport.ConstructionPlane Dim tropt As New Point3d(opt), trtpt As New Point3d(tpt) tropt.Transform(Transform.PlaneToPlane(Plane.WorldXY, CurrentPln)) trtpt.Transform(Transform.PlaneToPlane(Plane.WorldXY, CurrentPln))
Dim movestr As String = "_move " + String.Format("{0},{1},{2} ", tropt.X, tropt.Y, tropt.Z) + String.Format("{0},{1},{2} _Cancel _Cancel", trtpt.X, trtpt.Y, trtpt.Z) RhinoApp.RunScript(movestr, True) grpobj.Select(False) End If
Next
'RhinoApp.RunScript("Cancel", False) 'RhinoApp.RunScript("Cancel", False) '' rh.Views.RedrawEnabled = True Reslist.Add(Now & "_替换成功!(Replace Success!)") Catch ex As Exception Reslist.Add(Now & "_替换失败!(Replace failed!)" & vbCrLf & ex.Message)
End Try ' Grasshopper.Instances.ActiveCanvas.ModifiersEnabled = True
line1: DA.SetDataList(0, Reslist) End Sub
'Private Sub Testt_PingDocument(sender As IGH_DocumentObject, e As GH_PingDocumentEventArgs) Handles Me.PingDocument ' Dim Mbool = Aggregate bcbool In Checked Into cb = Any(bcbool)
' If Not Mbool Then ' Checked(0) = True ' Message = Namestr(0) ' Order = 0 ' End If 'End Sub
End Class
The picture below shows the two question.
Question One I must use data dam, or the component can't batch deal the brep. I don't know why, I have You can give me a solution to make it working normal not using the data dam
Question Two I can not uset the Button component, If I use it, the gh canvas will die with some mouse event--. I have see this problem before in this forum,but there is no solution and explain. I want to know why and How to solve it.
I don't know if I have made my question clear,if not give a message. Thank you! Thank you all.
The gh test file and 3dm test file in the upload files.
…