o Grasshopper and Rhino.Schedule: Rhinoceros1. NURBS and Mesh geometries.2. Complex geometries.3. GH to Rhinoceros workflow.Grasshopper1. Introduction to parametric design2. Parameters and components.3. Math and logics.4. 2D and 3D modeling.5. Simple definition6. Application to typical deisgn problems.SoftwareRhino + GrasshopperVenueParametric Support, Hardenbergstrasse 38, BerlinFee[Early Bird] 400 eur + VAT (until 11/11)[Regular] 420 eur + VAT[Student] 300 eurMore:hello@parametric.support…
----------
2;0
0
d
1
e
2
f
Path Mapper have a very interesting behavior, sometimes speed up things really easy.
(I've used the -1 to make paths start from 0 instead than from 1, with an input tree with 0 length branches or minimum branches length = 2 you will need to edit that)
:D
…
j
1
c
e
h
k
2
f
-------------------------------------------------------------------------------------------------
To these...
0;0
0;1
0
a
i
------------------------------------------------------------
0;0
0;1
0;2
0
b
g
j
1
c
h
k
------------------------------------------------------------
0;0
0
d
1
e
2
f
------------------------------------------------------------
Thanx……
NONE, in SIZING:PARAMETERS". I'm not sure of where to start in troubleshooting this. I've attached the file.
Thank you,
See the errors and warnings below:
{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. [1 of 8] Writing simulation parameters...
3. [2 of 8] Writing context surfaces...
4. [2 of 8] Writing context surfaces...
5. [3 of 8] Writing geometry...
6. [4 of 8] Writing Electric Load Center - Generator specifications ...
7. [5 of 8] Writing materials and constructions...
8. [6 of 8] Writing schedules...
9. [7 of 8] Writing loads and ideal air system...
10. [8 of 8] Writing outputs...
11. ...
... idf file is successfully written to : R:\Green\SuRG\Building_Performance_Analysis\2016_analysis_studies\Energy_Analysis_Comparison\Honeybee_+_Ladybug\tutorial01\EnergyPlus\tutorial01.idf
12.
13. Analysis is running!...
14. ...
...
Done! Read below for errors and warnings:
15.
16. Program Version,EnergyPlus, Version 8.5.0-c87e61b44b, YMD=2016.10.31 11:39,IDD_Version 8.5.0
17.
18. ************* IDF Context for following error/warning message:
19.
20. ************* Note -- lines truncated at 300 characters, if necessary...
21.
22. ************* 24 Sizing:Parameters,
23.
24. ************* Only last 1 lines before error line shown.....
25.
26. ************* 25 None, !- Heating Sizing Factor
27.
28. ** Severe ** IP: IDF line~25 Invalid Number in Numeric Field#1 (Heating Sizing Factor), value=NONE, in SIZING:PARAMETERS
29.
30. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
31.
32. ** ~~~ ** Possible Invalid Numerics or other problems
33.
34. ** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
35.
36. ...Summary of Errors that led to program termination:
37.
38. ..... Reference severe error count=1
39.
40. ..... Last severe error=IP: IDF line~
, value=NONE, in SIZING:PARAMETERS
41.
42. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
43.
44. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
45.
46. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
47.
48. ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
49.
50. ************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 9.34sec
51.…
s that setbacks are not possible to input using the thresholds component for that particular example because the OpenStudio apartment schedule doesn't have setbacks. I totally get this.
However, I get the same error for the office and classroom programs, and looking at the IDF file it's clear that both of these programs do have setbacks. In fact, I discovered this issue because I was trying to model a classroom with heating (<18 dC) but no cooling (>40 dC) and kept getting high cooling energy usage. The setback in the IDF file appears to default to 27 dC:
This probably explains why even though the max zone temp that is registering is 38 dC and my thermostat is set to 40 dC, I'm seeing a lot of cooling energy use. Is there a way of changing the setback through Honeybee?
…
st {A;B;C;D;E} > {A;B;C;D}, without repeating the line?
I see it deletes all the branches with only 4 paths, so you have to specify all the possibilities (branches with levels A to E, and A to D), but not sure why A to D isn't included when A to E is specified?
Second question, which is slightly off topic, is why did the curve-line intersection lose the path structure? Both trees had 38 branches.. I've uploaded a screenshot. Just to understand the way it works a bit better..
Thanks for your (amazingly quick!) help :)…