e structure systems. It presents an algorithmic process where the initial generative rule is based on the growth of Cellular Automata (CA). Digital Fabrication techniques will be used for prototyping. Theoretical lectures about Cellular Automata, Generative design and fabrication techniques will be presented .
Duration : 21 June. – 28 June. 2013 from 10 am to 6 pm Location : ENCODE Studio Address: 2 Wataneya buildings , 14 May Bridge , Smouha , Floor 1 , Apartment 106 Tel: 03-3823637 Mob: 0100-9879995 Email: encodestudio.mail@gmail.com Website: www.encodestudio.net for more information and registration please fill the following form : https://docs.google.com/forms/d/1FC9-CIDsNuzMkmu3Rubj45_7zTBb6YB3OfYnEA9xOMk/viewform?edit_requested=true Attendance Confirmation email will be sent to confirm availability…
ty lots as extrusions with their height depending on perimeter length. Then I added a 'Cull Duplicates' group to avoid properties that had duplicate 'Area' centroid points. That reduced the number of properties from 364 down to 331, though five of those have 'Area' values between 88 and 205, ten have values less than 500 while the average is ~1.3 million!
So the data is still suspect. Some appear to be nested inside of others? But using those 331 properties, I now find 32 that intersect the 'Zoning Districts'. But that's not the same as a list of properties that span two or more 'Zoning Districts'... Not having fun anymore. :)
…
Added by Joseph Oster at 10:40am on January 14, 2016
pen Brep"; I didn't know it worked on flat surfaces. And I think it's only fair to include in your benchmark the considerable time 'SUnion' takes in this example: 21.9 seconds for 121 rings and likely much more with 400 or 1,000+ rings.
Then I noticed the pattern doesn't match. Checked the circles and they are the same. The distance between them, however, is different: 7 instead of 6. When I change that value to 6, the Python fails badly. All the holes and gaps are gone, which destroys the pattern:
I can't do the "two phase" approach on an 11 X 11 grid, but I can do 6 X 6 and 2 X 2 to get a 12 X 12 grid (40 'SUnion' operations) in 28 seconds total. That beats your benchmark of ~37 seconds for an 11 X 11 grid, if you include the 'SUnion' in your code.
…
l equations that describe his attractor in a chaotic behavior when rho > 24.7. All the values of X =sigma(Y-X) *dt never repeat themselves through each moment in time making their distribution totaly random, we can see this at the end of the video with the linear graph. The beautiful thing is that even though the values of X are randomly distribuited over time, the result is a beautiful ordered shape, this in essence is the principal of chaotic systems. Or as James Gleick would say " chaotic systems embed hidden ordering principles"
X =sigma(Y-X)
Y= -X*Z+rho*X-Y
Z = X*Y-betta*Z
X = dx/dt -------> change of X over time
Y = dy/dt -------> change of Y over time
Z= dz/dt -------> change of z over time
rho = 28
betta = 3/8
sigma = 10
http://mathworld.wolfram.com/LorenzAttractor.html…
思った感じになりません。
balls の代わりにplanarカーブを直接入れてみましたがエラーが出ます。
ファンクションにしてみたところ、forループので作った数値が反映されていません。
ファンクションのインスタンス?を出力していないと思い上記のようにしましたがエラーが出てしまいます。
以上の事から自分の認識が正しいのかよくわからなくなりました・・・
python自体の深いところをわかっているわけではないので余計こんがらがりました。
そこで、for b in ballsはどのような条件または使い方であれば使えるのでしょうか?
そして、上記のように別のオブジェクトに対しての使い方はどのようにすればできるのでしょうか?
2:同じファンクション内のdist = rs.Distance(self.pos,b.pos)についてですが
この文章も for b in balls によってbはBallのインスタンスであると定義?されたためb.posがbの位置であると分かるのでしょうか?
pythonは定義しなくても動いてしまうのでどのような時に使えるのか文章見ただけではよくわかりません・・・
大変細かいことかもしれませんが、よりpythonをしっかりと理解するためにも、どなたかわかる方ご教授いただけると幸いです。…
geode. The faceting system also references the original use of triangulation for mapping three dimensional landscapes.
My question responds to the need to control the edges lengths and angles within the triangles to make the process of construction possible. We are hoping to keep the edges under 28 inches and the minimum angle more than 15 degrees. What would be your suggestion in grasshopper?
Our process for getting the facet was also... the long way.
1. draw curves based on three dimension measurements of interior
2. networks surface the four curves
3. mesh surface
4. triangulate mesh
5. reduce polygons
6. splitmeshedge where necessary to make quadrilaterals triangles once more
Any suggestions?…
Added by Amanda Gann at 8:57pm on December 4, 2013
this common installation problem please find a tested remedy shared by one of the group members:
Comment by Iman Sheikhansari on August 26, 2019 at 8:33amDelete Comment
HiIf you are encountering a problem with rhino 6 versions don't worryFollow these steps.1. Download SYNTACTIC from https://sites.google.com/site/pirouznourian/syntactic-design2. Install it and go to the installation folder, Drag & drop SYNTACTIC(green one) over your grasshopper canvas.3. Close your rhino and reopen it. 4. Type GrasshopperDeveloperSettings5. Tick the Memory load *.GHA assemblies using COFF byte arrays option6. Run grasshopper and enjoy plugin
I hope this helps,
Best regards,
Pirouz
…
urface,like
surface0 had 41 floors
surface1 had 28 floors
surface2 had 21 floors
I tried to change the data matching of the <move> component but still can't make the result that I want.
beside that, are there any component can let the overlay boxes can separate like this:
i make it manually by bake and move and bake and move..............
please forgive my broken english.
thanks
my definition
MASS%20STUDY-1.gh…