ences, so not terribly important in the end. After all, it's not really worth going through a lot of trouble to get a 15% speed increase; 15% faster than slow is still pretty slow.
Also processor speed has pretty much peaked these past few years, there have been no more significant increases lately. Instead, manufacturers have started putting more cores on motherboards, which is something GH unfortunately cannot take advantage of.
Multi-threading (very high on the list for GH2) brings with it a promise of full core utilisation (minus the inevitable overhead for aggregating computed results), but there are some problems that may end up being significant. Here's a non-exhaustive list:
It's not possible to modify the UI from a non-UI thread. This is probably not that big a deal for Grasshopper components, especially since we can make methods such a Rhino.RhinoApp.WriteLine() thread safe.
Not all methods used by component code are necessarily thread safe. There used to be a lot of stuff in the Rhino SDK that simply wouldn't work correct or would crash if the same method was run more than once simultaneously. Rhino core team has been working hard to remedy this problem, and I'm confident we can fix any problems that still come up, though it may take some time. If components rely on other code libraries then the problem may not be solvable at all. So we need to make sure multi-threading is an optional property of components.
There's overhead involved in multi-threading, it's especially difficult to get a good performance gain when dealing with lots of very fast operations. The overhead in these cases can actually make stuff perform slower.
There's the question on what level should multi-threading be implemented. Obviously the lower the better, but that means a lot of extra work, complicated patterns of responsibilities and a lot of communications between different developers.
There's the question on how the interface should behave during solutions now. If all the computation is happening in a thread, the interface can stay 'live'. So what should it look like if a solution takes -say- 5 seconds to complete? Should you be able to see the waves of data streaming through the network, turning components and wires grey and orange like strobe lights? What happens if you modify a slider during a solution? Simple answer is to abort the current solution and start a new one with the new slider value. But as you slowly drag the slider from left to right, you end up computing 400 partial solution and never getting to a final answer, even though you could have computed 2 full solutions in the same time and given better feedback. Does the preview geometry in the Rhino viewports flicker in and out of existence as solutions cascade through the network?
…
y stages of design, mainly due to the large uncertainties that exist in these phases. Optimisation in the early phases may be helpful, but it does not provide the designers with more information on "where to go from here". Once the designer changes a parameter to suit a client requirement, legal requirement or other, the optimised result may very well be thrown out due to the parameter being changed having such a large effect.
I am hosting several workshops and focus groups in the next month (one for students at Victoria University of Wellington, one for architect practitioners and one for engineering practitioners) to teach the basics of Honeybee and Ladybug within Rhino as NZ is very new to any form of distributed modelling methods (using visual language programmes such as grasshopper and dynamo to communicate between design tools and building simulation program tools). In the focus groups, I am not focusing on the tool of Honeybee so much as I am asking the industry its opinions on the feasibility and wishes of developments such as Honeybee.
I find that many informal interviews I have been having have pointed to the question: Would you rather want to know the optimised concept or the most significant design parameters which you should be wary of at the early stages of design?
I am amazed at the capabilities of Honeybee because it has been such a pain to remodel anything for E+ and Radiance in the past. I particularly love the ability to generate hundreds of idfs with varying parameters within 10min, without having to set up some form of macro to do it. The visualisations of Honeybee are awesome! To say the very least. But as someone who is interested in doing a sensitivity analysis, say with Thermal Autonomy, I feel like there is a lacking element to analysis from an engineer and research/academic stand point.
The way I have set up my files actually create 300+ idfs with all the various different parameters. The parameter ranges only vary from a low, typical and high setting for power densities, WWR, schedules and insulation. These have all been drawn from a large 5 year project where we monitored commercial buildings here in NZ to gain a better understanding of data for purposes like this. I then run them in parallel as batch files and re-insert the data back into Honeybee.
What I am playing around with at the moment though is that, due to the fact that the TA component require so many additional components to then analyse the data in that form, and also that it does not simply give a numerical value in % for the space's performance, I need to re-evaluate the csv that it produces for further analysis.
I have only just begun to try doing some form of sensitivity analysis within Honeybee itself, but I was curious if there were already plugins within grasshopper which may already allow some form of sensitivity analysis.…
of them. If they were already suggested and deemed impossible, i apologize.First, it would be really cool to have a right-click menu item for any geometry retaining module, that does the following: bakes the geometry, then disconnects all inherited data from the module, and assigns the baked version as locally defined. This is a one-time only thing, of course - it would be cool because if you have a "step-definition", that is, you have clear bottlenecks in your dataflow, and at some point you become satisfied with what you have so far, and only need to manually tweak some stuff to move on, you can discard the "already solved part of your definition. It's just a sort of "casting in stone" of partial results, that helps especially with simple work-defs or helper-defs. You could also call it something kickass like "manual override" or "emergency/hand b(r)ake".Second, if you have a component that outputs to a lot of others, and you want to change it with something else, you usually have to painstakingly reconnect all those wires, and if it doesn't work out, you do it right back or undo until you fingers bleed. Just as there is an extract parameter upstream for locally defined values, a downstream "extend parameter" with one rightclick menu item would make switching between various components easier.
Third, maybe a hot-key that you press and then click on a wire, which creates a "data" component at that point, splitting the wire and effectively allowing you to hijack it.
Lastly, maybe this is a stupid question, but what happened to the "clusters"? I mean i know they ended abruptly because of technical difficulties, but collapsing a group to a single component like that was totally awesome.Oh, and a minor bug repor from the v7.053 - it's not important, but mildly annoying: when you have an embedded graft, flatten, reparam or expression into a plug, the component extends to the left with the nifty little icons, and that looks very nice, but the wires still go in the old place, so at first glance i always think the wires are plugged in wrong. Is it possible to move the plug along with the component icon edge, or at least make those little indicators smaller, so that the error is minimized?
Thanks for your time,Hope i was pertinent
Andrei I.ps: the lolcat component is adorable, but i do believe that overall worldwide grasshopper productivity has dropped by various increments of those 20 sec it takes for it to refresh. Sadly accustomed with the feeling of guilt associated to watching around 50 lolpics refresh, I suggest that every 5 refreshes or so, you get a "stop looking at this and get back to work" message. It is at least a good way to derogate responsibility for tempting people to watch kitty-pics all day. :D…
stand completely (i just don't get the math part...).The code can be found here: http://digitalsubstance.wordpress.com/subcode/
So i decided to make my own definition: a cube deformed by 5 attractors and i was wondering if someone can help me solve the meshing at the end of the definition because when i bake it, it gives me an open mesh and i don't understand why ? Waterfall meshes are not suitable for 3d printing... I don't think i've used the clean, weld, and unify faces in the good order ? Maybe there is a problem with the surfaces ?
Secondly i'm not very proud of the result of my cube because it's so deformed that it is a not a cube anymore... so i was wondering if a square grid of points can be deformed by an attractor but still keeping the straight boundary of the grid ?
I had an idea to make that: i make my points, create the vectors between the grid and the attractor points, calculate the distance between the grid points and the attractors: it gives me a list of distances that i remap to control the strengh of my attractors. On the other side i calculate the distance between the boundary of the grid and the grid points and it gives me a second list of numbers. So i wanna average the two list of numbers in such a way that the closest it is to the attractor it takes the distance from the first list and the further it is from the attractor (so the closest it is from the boundary) it takes the distance from the second list ?? I'm sorry for my bad english but even in french it's little bit hard for me to explain it ;). So what can i do to have a grid attracted by a point without moving the boundary points ??
And please don't tell me to cull the boundary points first, to deform the grid and to rebuild the grid after... it gives an ugly cube face at the end, even with a lot of polishing with weaverbird...
If someone has another idea to achieve that please tell me ;)
The first definition "CleanCubeMeshingHelp"is a little bit heavy so watch out if you have a small laptop (any ideas to make it work faster are welcomed !!)
The second one is the one with the two list of numbers.
Also a last questions: what is and when to use the "blur number", "interpolate data" and Weighted Average" under math utilities ??
Thank you in advance for you answers and i apologize for my lack of vocubulary.…
greatly appreciate it!!
You can write the number of the question and write your answer next to it, example:
1) a
2) c
3) a) Washington University in St. Louis
4) 2 weeks (1week+1week shipping)
5) 130
6) b
7) b
The survey questions are as follows:
1)
Did you 3D print before?
5)
How much did it cost (in dollars)?
a.
Yes, for a school project
a.
Between 20 & 50
b.
Yes, for a personal project
b.
Between 50 & 80
c.
Between 80 & 120
2)
Print size
d.
Please specify if otherwise: _____ dollars
a.
Between 2 & 6 cubic inches
b.
Between 6 & 12 cubic inches
6)
Do you think the price was expensive?
c.
Between 12 & 20 cubic inches
a.
Not at all
d.
Please specify if otherwise: ____cubic inches
b.
A little bit expensive
c.
Very expensive
3)
Where did you print your object?
a.
School
7)
Were you satisfied with the printed object?
b.
Outside school: _________________
a.
Yes, it was a great print without problems
b.
Not bad, some issues
4)
How long did it take to print?
c.
I was not satisfied, very bad quality
a.
___ days
b.
___ weeks
Thank you very much to all!!
PS: If you did many 3D prints, you can post multiple answers.
Wassef…
ion of both Ladybug and Honeybee. Notable among the new components are 51 new Honeybee components for setting up and running energy simulations and 15 new Ladybug components for running detailed comfort analyses. We are also happy to announce the start of comprehensive tutorial series on how to use the components and the first one on getting started with Ladybug can be found here:
https://www.youtube.com/playlist?list=PLruLh1AdY-Sj_XGz3kzHUoWmpWDXNep1O
A second one on how to use the new Ladybug comfort components can be found here:
https://www.youtube.com/playlist?list=PLruLh1AdY-Sho45_D4BV1HKcIz7oVmZ8v
Here is a short list highlighting some of the capabilities of this current Honeybee release:
1) Run EnergyPlus and OpenStudio Simulations - A couple of components to export your HBZones into IDF or OSM files and run energy simulations right from the grasshopper window! Also included are several components for adjusting the parameters of the simulations and requesting a wide range of possible outputs.
2) Assign EnergyPlus Constructions - A set of components that allow you to assign constructions from the OpenStudio library to your Honeybee objects. This also includes components for searching through the OpenStudio construction/material library and components to create your own constructions and materials.
3) Assign EnergyPlus Schedules and Loads - A set of components for assigning schedules and Loads from the Openstudio library to your Honeybee zones. This includes the ability to auto-assign these based on your program or to tweak individual values. You can even create your own schedules from a stream of 8760 values with the new “Create CSV Schedule” component. Lastly, there is a component for converting any E+ schedule to 8760 values, which you can then visualize with the standard Ladybug components
4) Assign HVAC Systems - A set of components for assigning some basic ASHRAE HVAC systems that can be run with the Export to OpenStudio component. You can even adjust the parameters of these systems right in Grasshopper.
Note: The ASHRAE systems are only available for OpenStudio and can’t be used with Honeybee’s EnergyPlus component. Also, only ideal air, VAV and PTHP systems are currently available but more will be on their way soon!
5) Import And Visualize EnergyPlus Results - A set of components to import numerical EnergyPlus simulation results back into grasshopper such that they can be visualized with any of the standard Ladybug components (ie. the 3D chart or Psychrometric chart). Importers are made for zone-level results as well as surface results and surfaces results can be easily separated based on surface type. This also means that E+ results can be analyzed with the new Ladybug comfort calculator components and used in shade or natural ventilation studies. Lastly, there are a set of components for coloring zone/surface geometry with EnergyPlus results and for coloring the shades around zones with shade desirability.
6) Increased Radiance and Daysim Capabilities - Several updates have also been made to the existing Radiance and Daysim components including parallel Radiance Image-based analysis.
7) Visualize HBObject Attributes - A few components have been added to assist with setting up honeybee objects and ensuing the the correct properties have been assigned. These include components to separate surfaces based on boundary condition and components to label surfaces and zones with virtually any of their EnergyPlus or Radiance attributes.
8) WIP Grizzly Bear gbxml Exporter - Lastly, the release includes an WIP version of the Grizzly Bear gbXML exporter, which will continue to be developed over the next few months.
And here’s a list of the new Ladybug capabilities:
1) Comfort Models - Three comfort models that have been translated to python for your use in GH: PMV, Adaptive, and Outdoor (UTCI). Each of these models has a “Comfort Calculator” component for which you can input parameters like temperature and wind speed to get out comfort metrics. These can be used in conjunction with EPW data or EnergyPlus results to calculate comfort for every hour of the year.
2) Ladybug Psychrometric Chart - A new interactive psychrometric chart that was made possible thanks to the releasing of the Berkely Center for the Built Environment Comfort Tool Code (https://github.com/CenterForTheBuiltEnvironment/comfort-tool). The new psychrometric chart allows you to move the comfort polygon around based on PMV comfort metrics, plot EPW or EnergyPlus results on the psych chart, and see how many hours are made comfortable in each case. The component also allows you to plot polygons representing passive building strategies (like internal heat gain or evaporative cooling), which will adjust dynamically with the comfort polygon and are based on the strategies included in Climate Consultant.
3) Solar Adjusted MRT and Outdoor Shade Evaluator - A component has been added to allow you to account for shortwave solar radiation in comfort studies by adjusting Mean Radiant Temperature. This adjusted MRT can then be factored into outdoor comfort studies and used with an new Ladybug Comfort Shade Benefit Evaluator to design outdoor shades and awnings.
4) Wind Speed - Two new components for visualizing wind profile curves and calculating wind speed at particular heights. These allow users to translate EPW wind speed from the meteorological station to the terrain type and height above ground for their site. They will also help inform the CFD simulations that will be coming in later releases.
5) Sky Color Visualizer - A component has been added that allows you to visualize a clear sky for any hour of the year in order to get a sense of the sky qualities and understand light conditions in periods before or after sunset.
Ready to Start?
Here is what you will need to do:
Download Honeybee and Ladybug from the same link here. Make sure that you remove any old version of Ladybug and Honeybee if you have one, as mentioned on the Ladybug group page.
You will also need to install RADIANCE, DAYSIM and ENERGYPLUS on your system. We already sent a video about how to get RADIANCE and Daysim installed (link). You can download EnergyPlus 8.1 for Windows from the DOE website (http://apps1.eere.energy.gov/buildings/energyplus/?utm_source=EnergyPlus&utm_medium=redirect&utm_campaign=EnergyPlus%2Bredirect%2B1).
“EnergyPlus is a whole building energy simulation program that engineers, architects, and researchers use to model energy and water use in buildings.”
“OpenStudio is a cross-platform (Windows, Mac, and Linux) collection of software tools to support whole building energy modeling using EnergyPlus and advanced daylight analysis using Radiance.”
Make sure that you install ENERGYPLUS in a folder with no spaces in the file path (e.g. “C:\Program Files” has a space between “Program” and “Files”). A good option for each is C:\EnergyPlusV8-1-0, which is usually the default locations when you run the downloaded installer.
New Example Files!
We have put together a large number of new updated example files and you should use these to get yourself started. You can download them from the link on the group page.
New Developers:
Since the last release, we have had several new members join the Ladybug + Honeybee developer team:
Chien Si Harriman - Chien Si has contributed a large amount of code and new components in the OpenStudio workflow including components to add ASHRAE HVAC systems into your energy models and adjust their parameters. He is also the author of the Grizzly Bear gbxml exporter and will be continuing work on this in the following months.
Trygve Wastvedt - Trygve has contributed a core set of functions that were used to make the new Ladybug Colored Sky Visualizer and have also helped sync the Ladybug Sunpath to give sun positions for the current year of 2014
Abraham Yezioro - Abraham has contributed an awesome new bioclimatic chart for comfort analyses, which, despite its presence in the WIP tab, is nearly complete!
Djordje Spasic - Djordje has contributed a number of core functions that were used to make the new Ladybug Wind Speed Calculator and Wind Profile Visualizer components and will be assisting with workflows to process CFD results in the future. He also has some more outdoor comfort metrics in the works.
Andrew Heumann - Andrew contributed an endlessly useful list item selector, which can adjust based on the input list, and has multiple applications throughout Ladybug and Honeybee. One of the best is for selecting zone-level programs after selecting an overall building program.
Alex Jacobson - Alex also assisted with the coding of the wind speed components.
And, as always, a special thanks goes to all of our awesome users who tested the new components through their several iterations. Special thanks goes to Daniel, Michal, Francisco, and Agus for their continuous support. Thanks again for all the support, great suggestions and comments. We really cannot thank you enough.
Enjoy!,
Ladybug + Honeybee Development Team
PS: If you want to be updated about the news about Ladybug and Honeybee like Ladybug’s Facebook page (https://www.facebook.com/LadyBugforGrasshopper) or follow ladybug’s twitter account (@ladybug_tool).
…
teraction for its Correlations cycle, AA Athens Visiting School scales up its design intentions in order to investigate links among discrete individual architectural systems in its 2013 version, Recharged.
Recharged with interconnectivity on different levels, the theme of investigation will revolve around the design of semi-independent design prototypes acting together to form elaborate unified results. The driving force in Cipher City: Recharged is the synergistic effect behind complex form-making systems where interactive design patterns arise out of a multiplicity of relatively simple rules.
In collaboration with the National Technical University of Athens, Cipher City: Recharged will explore participatory design and active engagement modeling and will continue building novel prototypes upon horizontal planes.
As in 2012, the design agendas of AA Athens and AA Istanbul Visiting Schools will directly create feedback on one another, allowing participation in either one or both Programmes.
Discounts
The AA offers several discount options for participants wishing to apply as a group or participants wishing to apply for both AA Istanbul and AA Athens Visiting Schools:
1. Standard application
The AA Visiting School requires a fee of £695 per participant, which includes a £60 Visiting Membership. If you are already a member, the total fee will be reduced automatically by £60 by the online payment system. Fees are non refundable.
2. Group registration
For group applications, there will be a range of discounts depending on the number of people in the group. The discounted fee will be applied to each individual in the group.
Type A. 3-6 people group: £60 (AA Membership fee) + 635*0.75 = £536.25 (25 %) Type B. 6-15 people group: £60 + 635*0.70 = £504.5 (30%) Type C. more than 15 people group: £60 + 635*0.65 = £472.75 (35%)
3. Participants attending both AA Istanbul and AA Athens | 40% discount
For people wishing to attend both AA Istanbul 2013 and AA Athens 2013, a discount of 40% will be made for each participant. (The participant will pay the £60 membership fee only once.)
£60 (AA Membership fee) + (635*0.60)*2 = £822
For more information in discounts, please visit:
http://ai.aaschool.ac.uk/athens/portfolio/discounts-2013/
Applications
The deadline for applications is 11 March 2013. A portfolio or CV is not required, only the online application form and payment. The online application can be reached from:
http://www.aaschool.ac.uk/STUDY/VISITING/athens…
Added by elif erdine at 12:33pm on December 13, 2012
peuvent se diviser une surface avec ne importe quel motif imaginable. 3. Ici, je fournir un moyen de le faire via Lunchbox ... cela fonctionne mais il est fixe et donc nous avons besoin de jouer avec des arbres de données afin de créer le motif approprié par cas. 4. L'autre composante est un joint C # qui fait beaucoup de choses autres que de diviser ne importe quelle collection de points avec de nombreux modèles (voir le modèle ANDRE que je ai fait pour vous). 5. Vous devez décomposer une polysurface en morceaux afin de travailler sur les subdivisions. 6. Je donne une autre définition ainsi que pourrait agir comme un tutoriel sur la façon de traiter des ensembles de points via des composants de GH standards et des méthodes classiques.
Avertissez si tous ceux-ci apparaissent floue pour vous: Si oui, je pourrais écrire une définition utilisant des composants de GH classiques - mais vous perdrez les variations de motifs de division.
mieux, Peter
…
and export the geometry out to VVVV to render it LIVE! RawRRRR. In this case, a digital audio workstation Ableton Live, a leading industrial standard in contemporary music production.
the good news is that VVVV and ableton live lite is both free.
https://www.ableton.com/en/products/live-lite/
i am not trying to use ipad as a controller for grasshoppper. I wanted to work with a timeline (similar to MAYA or Ableton or any other DAW(digital audio workstation)) inside grasshopper in an intuitive way. Currently there is no way of SEQUENCING your definition the way you want to see that i know of.
no more combersome export import workflows... i dont need hyperrealistic renderings most of the time. so much time invested in googling the right way to import, export ... mesh settings...this workflow works for some, for some not ...that workflow works if ... and still you cannot render it live nor change sequence of instruction WHILE THE VIDEO is played. and I think no one wants to present rhinoceros viewport. BUT vvvv veiwport is different. it is used for VJing and many custom audio visual installation for events, done professionally. you can see an example of how sound and visuals come together from this post, using only VVVV and ableton. http://vvvv.org/documentation/meso-amstel-pulse
I propose a NEW method. make a definition, wire it to ableton, draw in some midi notes, and see it thru VVVV LIVE while you sequence the animation the WAY YOU WANT TO BE SEEN DURING YOUR PRESENTATION FROM THE BEGINNING, make a whole set of sequences in ableton, go back change some notes in ableton and the whole sequence will change RIGHT INFRONT of you. yes, you can just add some sound anywhere in the process. or take the sound waves (sqaure, saw, whateve) or take the audio and influence geometric parameters using custom patches via vvvv. I cannot even begin to tell you how sophisticated digital audio sound design technology got last ten year.. this is just one example which isn't even that advanced in todays standard in sound design ( and the famous producers would say its not about the tools at all.) http://www.youtube.com/watch?v=Iwz32bEgV8o
I just want to point out that grasshopper shares the same interface with VVVV (1998) and maxforlive, a plug in inside ableton. audio mulch is yet another one that shares this interface of plugging components to each other and allows users to create their own sound instruments. vvvv is built based on vb, i believe.
so current wish list is ...
1) grasshopper recieves a sequence of commands from ableton DONE
thanks to sebastian's OSCglue vvvv patch and this one http://vvvv.org/contribution/vvvv-and-grasshopper-demo-with-ghowl-udp
after this is done, its a matter of trimming and splitting the incoming string.
2) translate numeric oscillation from ableton to change GH values
video below shows what the controll interface of both values (numbers) and the midi notes look like.
https://vimeo.com/19743303
3) midi note in = toggle GH component (this one could be tricky)
for this... i am thinking it would be great if ...it is possible to make "midi learn" function in grasshopper where one can DROP IN A COMPONENT LIKE GALAPAGOS OR TIMER and assign the component to a signal in, in this case a midi note. there are total 128 midi notes (http://www.midimountain.com/midi/midi_note_numbers.html) and this is only for one channel. there are infinite channels in ableton. I usually use 16.
I have already figured out a way to send string into grasshopper from ableton live. but problem is, how for grasshopper to listen, not just take it in, and interpret midi and cc value changes ( usually runs from 0 to 128) and perform certain actions.
Basically what I am trying to achieve is this : some time passes then a parameter is set to change from value 0 to 50, for example. then some time passes again, then another parameter becomes "previewed", then baked. I have seen some examples of hoopsnake but I couldn't tell that you can really control the values in a clear x and y graph where x is time and y is the value. but this woud be considered a basic feature of modulation and automation in music production. NVM, its been DONE by Mr Heumann. https://vimeo.com/39730831
4) send points, lines, surfaces and meshes back out to VVVV
5) render it using VVVV and play with enormous collection of components in VVVV..its been around since 1998 for the sake of awesomeness.
this kind of a digital operation-hardware connection is usually whats done in digital music production solutions. I did look into midi controller - grasshopper work, and I know its been done, but that has obvious limitations of not being precise. and it only takes 0 o 128. I am thinking that midi can be useful for this because then I can program very precise and complex sequence with ease from music production software like ableton live.
This is an ongoing design research for a performative exhibition due in Bochum, Germany, this January. I will post definition if I get somewhere. A good place to start for me is the nesting sliders by Monique . http://www.grasshopper3d.com/forum/topics/nesting-sliders
…
ers can be applied from the right click Context Menu of either a component's input or output parameters. With the exception of <Principal> and <Degrees> they work exactly like their corresponding Grasshopper Component. When a I/O Modifier is applied to a parameter a visual Tag (icon) is displayed. If you hover over a Tag a tool tip will be displayed showing what it is and what it does.
The full list of these Tags:
1) Principal
An input with the Principal Icon is designated the principal input of a component for the purposes of path assignment.
For example:
2) Reverse
The Reverse I/O Modifier will reverse the order of a list (or lists in a multiple path structure)
3) Flatten
The Flatten I/O Modifier will reduce a multi-path tree down to a single list on the {0} path
4) Graft
The Graft I/O Modifier will create a new branch for each individual item in a list (or lists)
5) Simplify
The Simplify I/O Modifier will remove the overlap shared amongst all branches. [Note that a single branch does not share any overlap with anything else.]
6) Degrees
The Degrees Input Modifier indicates that the numbers received are actually measured in Degrees rather than Radians. Think of it more like a preference setting for each angle input on a Grasshopper Component that state you prefer to work in Degrees. There is no Output option as this is only available on Angle Inputs.
7) Expression
The Expression I/O Modifier allows you change the input value by evaluating an expression such as -x/2 which will have the input and make it negative. If you hover over the Tag a tool tip will be displayed with the expression. Since the release of GH version 0.9.0068 all I/O Expression Modifiers use "x" instead of the nickname of the parameter.
8) Reparameterize
The Reparameterize I/O Modifier will only work on lines, curves and surfaces forcing the domains of all geometry to the [0.0 to 1.0] range.
9) Invert
The Invert Input Modifier works in a similar way to a Not Gate in Boolean Logic negating the input. A good example of when to use this is on [Cull Pattern] where you wish to invert the logic to get the opposite results. There is no Output option as this is only available on Boolean Inputs.
…