to incorporating math and geometry in computational design education, Paneling Tools
Marlo Ransdell, PhD Creative Director, at FSU , Digital Fabrication in Design Research and Education
Andy Payne, LIFT architects | Harvard GSD | FireFly
Jay H Song, Chair, Jewelry School of Design, Jewelry as Personal Expression, Extra+Ordinary@Jewelry.com
Pei- Jung (P.J.) Chen, Professor of Jewelry, SCAD
Gustavo Fontana, designer/co-founder nimbistand, Diseñar, desarrollar y comercializar productos por tu cuenta.
Joe Anand, CEO MecSoft Corporation, RhinoCAM
Julian Ossa, Chair, Industrial Design Director, Diseño – Una opción de vida a todo vapor!, UPB
Minche Mena, SHINE Architecture, Principal
J. Alstan Jakubiec, Daylighting and Environmental Performance in Architectural Design Solemma, LLC
Carlos Garnier R&D Director / Jaime Cadena – General Director, Plug Design, www.plugdesign.com.mx
Mario Nakov, www.chaosgroup.com [ V-Ray ]
Andres Gonzalez, RhinoFabStudio
Workshops:
o) Paneling Tools
o) RhinoCAM
o) Rhinology in Design, for Jewelry
o) Footwear
o) V-Ray: Jewelry Design
o) V-Ray: Architects and Industrial Designers
o) FireFly
o) J. Alstan Jakubiec, DIVA
The cost for each workshop or the Lectures is 95.0 US$
To register:
WORK-SHOPS April 2 - RHINO DAY
WORK-SHOPS April 3 - RHINO DAY
REGISTRATION RHINO DAY
NOTE: All students and faculty members that register to this event, will receive a Rhino 5 Educational License at the event.
…
- nickname is rather the best approach - and not on active group, but that's irrelevant anyway).
Step back (assuming that you are talking about the "Tens_from_random_blah_blah" definition):
1. Engineering is the art of demystifying (or we are promising that anyway, he he). This means that you start defining (better: outlining) some topology for things based on some "generic" rules (like the ones applied for the masts,cables,cones etc etc). These things are kept in some kind of structure (Lists, DataTrees etc). Things are few in 99.99999% of cases (i.e. : even the biggest membrane "module" has, say, 20-50 masts per "module").
2. Then ... handling things "individually" (mostly modifying) becomes the most critical part. See this (an x "possible" solution by combining a myriad of "options" : a no cones membrane solution, in plain English):
3. But the above is impossible (for more than obvious reasons). You should deploy masts in some high/low sequence in order to achieve some meaningful convex/concave formation that could work.
4. This "works" : 5. This doesn't:
6. This works partially (the formation at the back is "flat" == undo able):
7. This is utterly kitsch (and faulty as the case6 - the back portion):
So it's quite obvious that without a (quite complex) capability to individually control things (in this occasion : mast heights) the whole definition is a waste of computer time. Additionally the more the solution is "demystified" (some curve is defined, some random points are created, some masts are in place, some cables appear etc etc) the more additional constrains are required in order to "narrow" the possibilities (In plain English : sliders should control other sliders as regards their min/max values, true/false, you/me etc etc).
Remember that we are talking about ONE (mast height) out of a myriad things that you should control "manually" (it's utterly pointless to mastermind some kind of "generic" rules - or use naive attractors etc etc) .You'll see the difference when I'll completely reform the definition by adding individual control upon anything.
PS: what about the blocks? (the real life stuff that actually make any solution possible). Can you imagine a 2nd set of "restrictions" imposed by "a child to his parent"? (Assembly/Component modeling , that is).
more soon
…
ly this is a Rhino.Python problem and not a Grasshopper issue, but it could apply to both!
I was trying to take a simple example of moving a ball around and see how it could be animated through Rhino.Python. The code works great in wire frame with now memory issues at all. However, when I switch the view to Shaded or Rendered, things go south pretty quickly. The RAM usage of Rhino which was steady around 350mb (ish) now grows every frame after a minute or so, it is in the GB's and never drops even after the script has stopped.What gives? Clearly this must be possible because Bongo does something similar when it does animations. Check out my code below and I would love to hear your thoughts.
import time
import rhinoscriptsyntax as rs
import Rhino
height = 100
width = 100
x = 0
y = 0
xspeed = .1
yspeed = .3
start_time = time.time()
end_time = 60
run_time = 0
sphere = rs.AddSphere((x,y,0), 5)
while run_time < end_time:
x = x + xspeed
y = y + yspeed
if x > width/2 or x < -width/2:
xspeed = xspeed * -1
if y > height/2 or y < -height/2:
yspeed = yspeed * -1
rs.MoveObject(sphere, (xspeed, yspeed, 0))
Rhino.RhinoApp.Wait()
run_time = time.time() - start_time…
uick answers. Below you will find some suggestions, but don't think of them as rules and especially don't think of them as guarantees.
1. Choose a descriptive title for your post
Don't call your question "Help!" or "I have a problem" or "Deadline tonight!", but actually describe the problem you are having.
2. Be succinct but clear in your wording
People need to know some details about your problem in order to understand what sort of answers would satisfy you, but nobody cares about how angry your boss or how bad your teacher or how tight your deadline is. Talk about the problem and only the problem. If you don't speak English well, you should probably post in your native language as well as providing a Google Translation of your question.
3. Attach minimal versions of all the relevant files
If you have a GH/GHX file you have a question about, attach it to the post. Don't expect that people will recreate a file based on a screen-shot because that's a lot of pointless work. It's also a good idea to remove everything non-essential from a GH file. You can use the 'Internalise Data' menu option to cut everything to the left of a parameter:
If you're importing curves or Breps or meshes from Rhino, you can also internalise them so you won't have to post a 3DM file as well as a GH file. If you do attach large files, consider zipping them first. Do not use RAR, Ning doesn't handle it.
It is especially a good idea to post files that don't require any non-standard components if at all possible. Not everyone has Kangaroo or Hoopsnake or Geco installed so if your file relies on those components, it might not open correctly elsewhere.
4. Include a detailed image of the GH file if it makes sense
If your question is about a specific (group of) components, consider adding a screenshot of the file in the text of the post. You can use the Ctrl+Shift+Q feature in Grasshopper to quickly create nice screenshots with focus rectangles such as this:
5. Include links to online resources if possible
If you have a question about Schwarz Minimal surfaces, please link to a website which talks about these.
6. Create new topics rather than continuing old ones
It's usually better to start a fresh question, even if there's already a discussion that kinda sorta tangentially touches upon the same issue. Please link to that discussion, but start anew.
7. This is not a 'do my work for me' group
Many of us like to help, but it's good to see effort on our part being matched by effort on your part. Questions in the form of 'I need to do X but cannot be bothered to try and learn the software' will (and should) go unanswered.
7b. Similarly, questions in the form of 'How do I quickly recreate this facade that took a team of skilled professionals four months to figure out?' have a very low success rate.
--
David Rutten
Lead Grasshopper Development
Robert McNeel & Associates…
Added by David Rutten at 12:58pm on October 1, 2013
ting.
Thanks
Rania
** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
** Warning ** Version: in IDF="'8.2.7'" not the same as expected="8.2"
** Warning ** ManageSizing: For a zone sizing run, there must be at least 1 Sizing:Zone input object. SimulationControl Zone Sizing option ignored.
** Warning ** ManageSizing: For a plant sizing run, there must be at least 1 Sizing:Plant object input. SimulationControl Plant Sizing option ignored.
************* Testing Individual Branch Integrity
************* All Branches passed integrity testing
************* Testing Individual Supply Air Path Integrity
************* All Supply Air Paths passed integrity testing
************* Testing Individual Return Air Path Integrity
************* All Return Air Paths passed integrity testing
************* No node connection errors were found.
************* Beginning Simulation
************* Simulation Error Summary *************
** Warning ** The following Report Variables were requested but not generated
** ~~~ ** because IDF did not contain these elements or misspelled variable name -- check .rdd file
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR TOTAL COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR TOTAL HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=CHILLER ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=BOILER HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=FAN ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR LATENT HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR LATENT COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR SENSIBLE HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR SENSIBLE COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=SYSTEM NODE MASS FLOW RATE, Frequency=Hourly
************* Key=*, VarName=SYSTEM NODE TEMPERATURE, Frequency=Hourly
************* Key=*, VarName=SYSTEM NODE RELATIVE HUMIDITY, Frequency=Hourly
************* There are 3 unused schedules in input.
************* There are 5 unused week schedules in input.
************* There are 13 unused day schedules in input.
************* Use Output:Diagnostics,DisplayUnusedSchedules; to see them.
*************
************* ===== Recurring Surface Error Summary =====
************* The following surface error messages occurred.
*************
************* Base Surface does not surround subsurface errors occuring...
************* Check that the GlobalGeometryRules object is expressing the proper starting corner and direction [CounterClockwise/Clockwise]
*************
** Warning ** Base surface does not surround subsurface (CHKSBS), Overlap Status=No-Overlap
** ~~~ ** The base surround errors occurred 1 times.
** ~~~ ** Surface "839A5ADACCE44BC0AF00_GLZP_31" misses SubSurface "839A5ADACCE44BC0AF00_GLZP_31_GLZ_31"
** Warning ** Base surface does not surround subsurface (CHKSBS), Overlap Status=Partial-Overlap
** ~~~ ** The base surround errors occurred 1 times.
** ~~~ ** Surface "839A5ADACCE44BC0AF00_GLZP_34" overlaps SubSurface "839A5ADACCE44BC0AF00_GLZP_34_GLZ_34"
*************
** ~~~ ** The base surround errors occurred 2 times (total).
*************
************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
************* EnergyPlus Sizing Error Summary. During Sizing: 2 Warning; 0 Severe Errors.
************* EnergyPlus Completed Successfully-- 7 Warning; 0 Severe Errors; Elapsed Time=00hr 07min 35.94sec…
ion of both Ladybug and Honeybee. Notable among the new components are 51 new Honeybee components for setting up and running energy simulations and 15 new Ladybug components for running detailed comfort analyses. We are also happy to announce the start of comprehensive tutorial series on how to use the components and the first one on getting started with Ladybug can be found here:
https://www.youtube.com/playlist?list=PLruLh1AdY-Sj_XGz3kzHUoWmpWDXNep1O
A second one on how to use the new Ladybug comfort components can be found here:
https://www.youtube.com/playlist?list=PLruLh1AdY-Sho45_D4BV1HKcIz7oVmZ8v
Here is a short list highlighting some of the capabilities of this current Honeybee release:
1) Run EnergyPlus and OpenStudio Simulations - A couple of components to export your HBZones into IDF or OSM files and run energy simulations right from the grasshopper window! Also included are several components for adjusting the parameters of the simulations and requesting a wide range of possible outputs.
2) Assign EnergyPlus Constructions - A set of components that allow you to assign constructions from the OpenStudio library to your Honeybee objects. This also includes components for searching through the OpenStudio construction/material library and components to create your own constructions and materials.
3) Assign EnergyPlus Schedules and Loads - A set of components for assigning schedules and Loads from the Openstudio library to your Honeybee zones. This includes the ability to auto-assign these based on your program or to tweak individual values. You can even create your own schedules from a stream of 8760 values with the new “Create CSV Schedule” component. Lastly, there is a component for converting any E+ schedule to 8760 values, which you can then visualize with the standard Ladybug components
4) Assign HVAC Systems - A set of components for assigning some basic ASHRAE HVAC systems that can be run with the Export to OpenStudio component. You can even adjust the parameters of these systems right in Grasshopper.
Note: The ASHRAE systems are only available for OpenStudio and can’t be used with Honeybee’s EnergyPlus component. Also, only ideal air, VAV and PTHP systems are currently available but more will be on their way soon!
5) Import And Visualize EnergyPlus Results - A set of components to import numerical EnergyPlus simulation results back into grasshopper such that they can be visualized with any of the standard Ladybug components (ie. the 3D chart or Psychrometric chart). Importers are made for zone-level results as well as surface results and surfaces results can be easily separated based on surface type. This also means that E+ results can be analyzed with the new Ladybug comfort calculator components and used in shade or natural ventilation studies. Lastly, there are a set of components for coloring zone/surface geometry with EnergyPlus results and for coloring the shades around zones with shade desirability.
6) Increased Radiance and Daysim Capabilities - Several updates have also been made to the existing Radiance and Daysim components including parallel Radiance Image-based analysis.
7) Visualize HBObject Attributes - A few components have been added to assist with setting up honeybee objects and ensuing the the correct properties have been assigned. These include components to separate surfaces based on boundary condition and components to label surfaces and zones with virtually any of their EnergyPlus or Radiance attributes.
8) WIP Grizzly Bear gbxml Exporter - Lastly, the release includes an WIP version of the Grizzly Bear gbXML exporter, which will continue to be developed over the next few months.
And here’s a list of the new Ladybug capabilities:
1) Comfort Models - Three comfort models that have been translated to python for your use in GH: PMV, Adaptive, and Outdoor (UTCI). Each of these models has a “Comfort Calculator” component for which you can input parameters like temperature and wind speed to get out comfort metrics. These can be used in conjunction with EPW data or EnergyPlus results to calculate comfort for every hour of the year.
2) Ladybug Psychrometric Chart - A new interactive psychrometric chart that was made possible thanks to the releasing of the Berkely Center for the Built Environment Comfort Tool Code (https://github.com/CenterForTheBuiltEnvironment/comfort-tool). The new psychrometric chart allows you to move the comfort polygon around based on PMV comfort metrics, plot EPW or EnergyPlus results on the psych chart, and see how many hours are made comfortable in each case. The component also allows you to plot polygons representing passive building strategies (like internal heat gain or evaporative cooling), which will adjust dynamically with the comfort polygon and are based on the strategies included in Climate Consultant.
3) Solar Adjusted MRT and Outdoor Shade Evaluator - A component has been added to allow you to account for shortwave solar radiation in comfort studies by adjusting Mean Radiant Temperature. This adjusted MRT can then be factored into outdoor comfort studies and used with an new Ladybug Comfort Shade Benefit Evaluator to design outdoor shades and awnings.
4) Wind Speed - Two new components for visualizing wind profile curves and calculating wind speed at particular heights. These allow users to translate EPW wind speed from the meteorological station to the terrain type and height above ground for their site. They will also help inform the CFD simulations that will be coming in later releases.
5) Sky Color Visualizer - A component has been added that allows you to visualize a clear sky for any hour of the year in order to get a sense of the sky qualities and understand light conditions in periods before or after sunset.
Ready to Start?
Here is what you will need to do:
Download Honeybee and Ladybug from the same link here. Make sure that you remove any old version of Ladybug and Honeybee if you have one, as mentioned on the Ladybug group page.
You will also need to install RADIANCE, DAYSIM and ENERGYPLUS on your system. We already sent a video about how to get RADIANCE and Daysim installed (link). You can download EnergyPlus 8.1 for Windows from the DOE website (http://apps1.eere.energy.gov/buildings/energyplus/?utm_source=EnergyPlus&utm_medium=redirect&utm_campaign=EnergyPlus%2Bredirect%2B1).
“EnergyPlus is a whole building energy simulation program that engineers, architects, and researchers use to model energy and water use in buildings.”
“OpenStudio is a cross-platform (Windows, Mac, and Linux) collection of software tools to support whole building energy modeling using EnergyPlus and advanced daylight analysis using Radiance.”
Make sure that you install ENERGYPLUS in a folder with no spaces in the file path (e.g. “C:\Program Files” has a space between “Program” and “Files”). A good option for each is C:\EnergyPlusV8-1-0, which is usually the default locations when you run the downloaded installer.
New Example Files!
We have put together a large number of new updated example files and you should use these to get yourself started. You can download them from the link on the group page.
New Developers:
Since the last release, we have had several new members join the Ladybug + Honeybee developer team:
Chien Si Harriman - Chien Si has contributed a large amount of code and new components in the OpenStudio workflow including components to add ASHRAE HVAC systems into your energy models and adjust their parameters. He is also the author of the Grizzly Bear gbxml exporter and will be continuing work on this in the following months.
Trygve Wastvedt - Trygve has contributed a core set of functions that were used to make the new Ladybug Colored Sky Visualizer and have also helped sync the Ladybug Sunpath to give sun positions for the current year of 2014
Abraham Yezioro - Abraham has contributed an awesome new bioclimatic chart for comfort analyses, which, despite its presence in the WIP tab, is nearly complete!
Djordje Spasic - Djordje has contributed a number of core functions that were used to make the new Ladybug Wind Speed Calculator and Wind Profile Visualizer components and will be assisting with workflows to process CFD results in the future. He also has some more outdoor comfort metrics in the works.
Andrew Heumann - Andrew contributed an endlessly useful list item selector, which can adjust based on the input list, and has multiple applications throughout Ladybug and Honeybee. One of the best is for selecting zone-level programs after selecting an overall building program.
Alex Jacobson - Alex also assisted with the coding of the wind speed components.
And, as always, a special thanks goes to all of our awesome users who tested the new components through their several iterations. Special thanks goes to Daniel, Michal, Francisco, and Agus for their continuous support. Thanks again for all the support, great suggestions and comments. We really cannot thank you enough.
Enjoy!,
Ladybug + Honeybee Development Team
PS: If you want to be updated about the news about Ladybug and Honeybee like Ladybug’s Facebook page (https://www.facebook.com/LadyBugforGrasshopper) or follow ladybug’s twitter account (@ladybug_tool).
…
, Engineer and Researcher from France with broad programming experience. He is the author of the City in 3D Rhinoceros plugin for creation of buildings according to geojson file and with real elevation. Guillaume already created a new component: "Address to Location". It enables getting latitude and longitude values for the given address:
2) Support of Bathymetry data: automatic creation of underwater (sea/river/lake floor) terrain. This feature is now available through new source_ input of the "Terrain generator" component. Here is an example of terrain of the Loihi underwater volcano, of the coast of Hawaii:
3) A new terrain source has been added: ALOS World 3D 30m. ALOS is a Japanese global terrain data. Gismo "Terrain Generator" component has been using SRTM 30m terrain data, which hasn't been global and was limited to -56 to +60 latitude range. With this addition, it is possible to switch between SRTM and ALOS World 3D 30m models with the use of source_ input.
4) 9 new components have been added:
"Address To Location" - finds latitude and longitude coordinates for the given address.
"XY To Location" - finds latitude and longitude coordinates for the given Rhino XY coordinates. "Location To XY" - vice versa from the previous component: finds Rhino XY coordinates for the given latitude longitude coordinates. "Z To Elevation" - finds elevation for particular Rhino point. "Rhino text to number" - convert numeric text from Rhino to grasshopper number. "Rhino unit to meters" - convert Rhino units to meters. "Deconstruct location" - deconstructs .epw location. "New Component Example" - this component explains how to make a new Gismo component, in case you are interested to make one. We welcome new developers, even if you contribute a single component to Gismo! "Support Gismo" - gives some suggestions on how to make Gismo better, how to improve it and support it.
5) Ladybug "Terrain Generator" component now supports all units, not only Meters. So any Gismo example file which uses this component, can now use Rhino units other than Meters as well. Thank you Antonello Di Nunzio for making this happen!!
Basically just forget about this yellow panel:
This panel is not valid anymore, so just use any unit you want.
6) A number of bugs have been fixed, reported in topics for the last couple of weeks. We would like to thank members in the community who invested their time in testing, finding these bugs and reporting them: Rafat Ahmed, Peter Zatko, Mathieu Venot, Abraham Yezioro, Rafael Alonso. Thank you guys!!! Apologies if we forgot to mention someone.
The version 0.0.2 can be downloaded from here:
https://github.com/stgeorges/gismo/zipball/master
And example files from here:
https://github.com/stgeorges/gismo/tree/master/examples
Any new suggestions, testing and bug reports are welcome!!…
Added by djordje to Gismo at 5:13pm on March 1, 2017
But not just any gum tree. The angophora, no less:
Why? Because I like nature, that's why. Every time I see new designs –especially architectural designs– it worries me that the natural environment is being taken over. Not just that, but even the new materials used in all product designs has to come from nature as well [read: mines].
So. People are forgetting that we still need trees and I believe that if someone sees a beautiful [read: established] tree in their architectural plans, they are going to be much more likely to build around it and not cut it down. That alone would no doubt increase the value of the house.
My thinking is that current tree models suck. They look unnatural and I think I know why. They're not random or organic enough. They're not detailed enough. That's basically my 'rationale' for this project. Just look at how different all of these tree trunks are!
So I am not being paid for this project. It's a personal project of mine. I'm just worried about the trunk shape for now — I'll worry about all the leaves... when I get to that.
I am a grasshopper beginner. Please keep that in mind. I am also fairly hopeless at traditional programming, but I find the visual approach of grasshopper much easier to grasp. So unfortunately I have gotten stuck and need some help, even just a clue, as to how to proceed.
That said, here is my current progress:
About a year ago, I started modelling with straight trunks using pipe sections, to see if I could get a very basic "tree" shape. And to see if I could join the segments together. Yes it works but it looks hopeless as you can imagine. Then I stopped for a long while. Now I'm back at it, hoping to improve a lot more.
I have already made one basic vertical nurbs curve with tangents at either end as the main "trunk".
I tried creating two ellipses at each end of the main trunk/curve and lofting between them but it omitted the main curve/rail. So it ended up being an elliptical trunk with straight sides which of course still didn't look right.
Then I divided the first main curve up into a number of segments. I think that is a better approach.
I have taken the parameters of the curve at each segment (probably the tangent, but I am unsure what the exact parameter is) and used that to form a basic angled plane at each segment/division.
I have been able to draw ellipses at each segment and rotate them onto the plane.
I was going to loft it together later on. A Curved loft with elliptical cross-sections looks much better than straight a pipe does, but still looks too unnatural.
I quickly realised that tree trunks are not elliptical, but rather, shaped more like 'kidneys'.
The next step was to create >3 points on each of those planes (spaced fairly evenly around the ellipse so as not to create a really funky/unwanted shape).
Maybe it would be better to model with a triangle or other polygon instead of an ellipse. I haven't got that far yet... because here is where I am getting stuck.
I managed to find a way of getting three roughly 'triangular' points along each that ellipse.
I also managed to create three nurbs cuves in the Z direction which intersected those three points, a bit like three seams down the side of the tree trunk, but couldn't figure out how to loft it all together.
I think it was the wrong approach anyway... I'd rather try to create a bunch of nurbs curves at each of the XY planes so as to get more control of the shape.
What I am trying to do now is create three roughly triangular-spaced points on a basic ellipse through which I can then draw a simple nurbs curve (think like a cross section of the trunk).
I would then like to add some XY-only randomness to the positions of those points. Not Z randomness, otherwise the trunk is going to get messed/kinked up. That's probably very important.
Then I would like to loft those nurbs curvs at each XY plane together forming the basic tree trunk, which also tapers based on some other variable (a non-linear factor, not simply distance from ground plane, perhaps something else?).
I have attached the GH file.
I am also open to suggestions if you have a better way of solving a problem. I would like to retain control over a lot of factor such as number of branches, spacing, average branch length, etc. My main contrsaints are that the entire thing has to be somewhat random and non-linear.
…