ches it with the first branch in Tree B (and then the first branch in Tree C if more than two trees are involved).
I'm planning to add better branch matching logic, but I'm not going to touch it until I have a good idea about what's needed and how it can be accomplished without breaking existing files.
So, the branch "address" is only used to sort the branches in a single tree. Thus, a tree with the following branches is always sorted in the exact same way:
{0;0}
{0;1}
{0;2}
{0;3;0}
{0;3;1}
{1;6}
If you have another tree with different branches:
{0}
{1}
{2}
{3}
{4}
{5}
Then the matching will be:
{0;0} -> {0}
{0;1} -> {1}
{0;2} -> {2}
{0;3;0} -> {3}
{0;3;1} -> {4}
{1;6} -> {5}
As long as people adhere to your advice: "it is best for the addresses of each tree branch to be in the same format", there will be no problem. But it is at the moment extremely difficult to perform complex matchings.
--
David Rutten
david@mcneel.com
Poprad, Slovakia…
Added by David Rutten at 9:25am on August 11, 2010
a seed, and instead creating a pattern where each color has a seed/control slider for each row? For example, row 1: brown 2, tan 6, yellow 7, purple 3, repeat. row 2: brown 6, tan 1, yellow 4, purple 10, repeat. row 3: yellow 5, purple 1, brown 3, tan 10, repeat. row 4: purple 2, brown 7, tan 3, yellow 4, repeat. Then repeat that sequence up the wall? For each color, the number in the sequence should be adjustable.
Thank you again for your help!…
{0;1;0}N=6
{0;1;1}N=6
{0;1;2}N=5
{0;2;0}N=7
{0;2;1}N=8
{0;2;2}N=9
Can you shift and wrap any of the paths A B or C?
Say if I wanted to shift and wrap B by 1 to get the following...
{0;0;0}N=7
{0;0;1}N=8
{0;0;2}N=9
{0;1;0}N=3
{0;1;1}N=2
{0;1;2}N=5
{0;2;0}N=6
{0;2;1}N=6
{0;2;2}N=5…
{4}-0;3
{5}-6;7
{6}-5;7
{7}-5;6
Here it can be shown that there are two subgraphs containing 0,1,2,3,4 and 5,6,7. How can I use spiderweb (either using scripting or the components) to give me this result when I have many more vertices??
Thanks,
Sam…
6, 7, 8, 9, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30, etc
In addition to the components in the attached file, I have also tried using Cull Index but that did not do much. I tried using a number slider set to whole numbers with the range equal to the values I have set up in the integer, but it just increases the size by 1 every time. Any help on steps in the right direction would be great thanks.…
ld go
Slider at 1 -> 1°, 2°, 3°.
Slider at 2 -> 2°, 4°, 6°
Slider at 3, etc.
And when the angle was too much that it surpassed 90 before connecting the 20 points, that line was not created. Maybe using a series instead of a range...mmm
Everything helps, thanks
…