EP output variables are to calculate outdoorAirEnergy?
Thank you very much!
Output variables on the Read EP Results component:[1] totalThermalEnergy=cooling+heating[2] thermalEnergyBalance=cooling (-)andheating (+)[3] cooling= Zone Ideal Loads Supply Air Total Cooling Energy [J](Hourly)=Zone Ideal Loads Supply Air Sensible Cooling Energy [J](Hourly)+ Zone Ideal Loads Supply Air Latent Cooling Energy [J](Hourly)[4] heating= Zone Ideal Loads Supply Air Total Heating Energy [J](Hourly)= Zone Ideal Loads Supply Air Sensible Heating Energy [J](Hourly) + Zone Ideal Loads Supply Air Latent Heating Energy [J](Hourly)[5] electricLight=Zone Lights Electric Energy [J](Hourly)[6] electricEquip=Electric Equipment Electric Energy [J](Hourly)[7] peopleGains=Zone People Total Heating Energy [J](Hourly)[8] totalSolarGain=Zone Windows Total Transmitted Solar Radiation Energy[9] infiltrationEnergy=Zone Infiltration Total Heat Gain Energy (+)andZone Infiltration Total Heat Loss Energy (-)[10] outdoorAirEnergy= ???[11] natVentEnergy=Zone Ventilation Total Heat Gain Energy (+)andZone Ventilation Total Heat Loss Energy (-)[12] operativeTemperature=Zone Operative Temperature[13] airTemperature=Zone Mean Air Temperature[14] meanRadTemperature=Zone Mean Radiant Temperature[15] relativeHumidity=Zone Air Relative Humidity[16] airFlowVolume=[infiltrationFlow] Zone Infiltration Standard Density Volume Flow Rate+[natVentFlow] Zone Ventilation Standard Density Volume Flow Rate+[mechSysAirFlow] Zone Mechanical Ventilation Standard Density Volume Flow Rate+[earthTubeFlow] Earth Tube Air Flow Volume[17] airHeatGainRate=[surfaceAirGain] Zone Air Heat Balance Surface Convection Rate+[systemAirGain] Zone Air Heat Balance System Air Transfer Rate
Output variables on the Read EP Surface Results component:[1] surfaceIndoorTemp= Surface Inside Face Temperature[2] surfaceOutdoorTemp=Surface Outside Face Temperature[3] surfaceEnergyFlow=[opaqueEnergyFlow] Surface Average Face Conduction Heat Transfer Energy+[glazEnergyFlow] Surface Window Heat Gain Energy[4] opaqueEnergyFlow =Surface Average Face Conduction Heat Transfer Energy[5] glazEnergyFlow= Surface Window Heat Gain Energy[6] windowTotalSolarEnergy=Surface Window Transmitted Solar Radiation Energy[7] windowBeamEnergy=Surface Window Transmitted Beam Solar Radiation Energy[8] windowDiffEnergy=Surface Window Transmitted Diffuse Solar Radiation Energy[9] windowTransmissivity=Surface Window System Solar Transmittance…
his comes in the form of an HTML page with links to every component, so you will need to view it in your web browser. (I use Chrome and it doesn't seem to be working correctly, but when opened in IE its fine.)
2) Included in each help topic for each component is the Inputs and Outputs descriptions and data types.
3) You supply the data. What you supply and how you supply it is for you to decide. There are umpteen different ways. Are you asking for a list of those ways for each input?
4) Points can either be Rhino objects or 3D co-ordinates. To create a point you can use any of these methods, but it mostly comes down to user preference. I like using Panels as this displays outside of the component.
5) Because of the nature of vectors they represent magnitude and direction but they don't have an independent location, so there is a component that will display vectors in Rhino.
6) The user.
7) There is a Primer on the front page. Here you find the Basics, but because GH is ever evolving in its current beta state you might find things that aren't relevant any more or simply don't work the same. And here is the reason why nobody is writing an update because it could be soon out of date.
8) Importing images by either dragging them from explorer onto the canvas or right click context menu Image...
9) Single line = Single Item of Data. Double line = Multiple items of data on the same Branch. Dashed Double Line = Multiple Data on Multiple Branches.
10) User preference
11) Toolbar management is probably the bane of David's life. Most things are logically placed. For example the Curve Tab, Primitives are any simple curve types that you are creating from scratch. Similarly Splines is for more complex curve types created from scratch. Analysis is where you find components that are finding answers supplied by curves, control points, curvature, parameters, end points etc. Division is a subset of this category but has a group of its own. And Utilities is where you find curve related actions that you want to perform, offsetting, rebuilding projecting, exploding etc.
12) I would image it would have been the Point On Curve component in Curve>Analysis. Why that group? You are not putting a point on a curve you are analysing a curve for the location of a point based on some parameters that you are supplying. For example "what is the mid point?"
I hope this goes some way towards answering you questions. No doubt this will have generated more so don't be afraid to ask, it took me several releases of Explicit History (aka Grasshopper) before I realised what the egg did, it never occurred to me that I could put my objects into Rhino when I was finished. Or the fact that I could use panels to 'see' data outputs.
Al the best,
Danny…
Added by Danny Boyes at 3:48am on December 9, 2010
should follow the instruction which mostapha has wrote in https://github.com/mostaphaRoudsari/ladybug/blob/master/resources/I...
Instructions for Installing Ladybug + Honeybee: (Follow steps 1-6 for basic functionality and 1-11 for full functionality) 0. If you have an old version of LB+HB, download the file here (https://app.box.com/s/ds96em9l6stxpcw8kgtf) and open it in Grasshopper to remove your old Ladybug and Honeybee version. 1. Make sure that you have a working copy of both Rhino and Grasshopper installed. 2. Open Rhino and type "Grasshopper" into the command line (without quotations). Wait for grasshopper to load. 3. Install GHPython by downloading the file at this link (http://www.food4rhino.com/project/ghpython?ufh) and drag the .gha file onto the Grasshopper canvas. 4. Select and drag all of the files in the "userObjects" folder (downloaded with this instructions file) onto your Grasshopper canvas. You should see Ladybug and Honeybee appear as tabs on the grasshopper tool bar. (If you are reading this instruction on github you can download them from http://www.food4rhino.com/project/ladybug-honeybee) 5. Download the files at this link (https://app.box.com/s/bh9sbpgajdtmmystv3n4), unzip them and copy the contents to both C:\ladybug and C:\Users\[yourUsername]\AppData\Roaming\Ladybug. 6. Restart Rhino and Grasshopper. You now have a fully-functioning Ladybug. For Honeybee, continue to the following: 7. Install Radiance to C:\Radiance by downloading it from this link (https://github.com/NREL/Radiance/releases/download/4.2.2/radiance-4...) and running the exe. 6. Install Daysim to C:\DAYSIM by downloading it at this link (http://daysim.ning.com/page/download) and running the exe. 8. Install Energy Plus 8.1 to C:\EnergyPlusV8-1-0 by going to the DOE website (http://apps1.eere.energy.gov/buildings/energyplus/energyplus_downlo...), making an account, going to "download older versions of EnergyPlus, selecting 8.1 and running the exe. 9. Copy falsecolor2.exe (http://pyrat.googlecode.com/files/falsecolor2.exe) and evalglare.exe (http://www.ise.fraunhofer.de/en/downloads-englisch/software/evalgla...) to C:\Radiance\bin 10. Download the OpenStudio Libraries (https://app.box.com/s/y2sx16k98g1lfd3r47zi) and unzip them to C:\ladybug\OpenStudio. 11. You now have a fully-working version of Ladybug + Honeybee. Get started visualizing weather data with these video tutorials (https://www.youtube.com/playlist?list=PLruLh1AdY-Sj_XGz3kzHUoWmpWDX...).
It works for me..
Agus…
ocessed once Grasshopper is done with whatever it's doing now.
3) Grasshopper tells the Slider object that the mouse moved and the slider works out the new value as implied by the new cursor position.
4) The slider then expires itself and its dependencies ([VB Step 1] in this case, but there can be any number of dependent objects).
5) When [VB Step 1] is expired by the slider, it will in turn expire its dependencies (VB Step 2), and so on, recursively until all indirect dependencies of the slider have been expired.
6) When the expiration shockwave has subsided, runtime control is returned to the slider object, which tells the parent document that stuff has changed and that a new solution is much sought after.
7) The Document class then iterates over all its objects (they are stored in View order, not from left to right), solving each one in turn. (Assuming the object needs solving, but since in your example ALL objects will be expired by a slider change, I shall assume that here).
8) It's hard to tell which object will get triggered first. You'd have to superimpose them in order to see which one is visually the bottom-most object, but let's assume for purposes of completeness that it's the [VB Step 1] object which is solved first.
9) [VB Step 1] is triggered by the document, which causes it to collect all the input data.
10) The input parameter [x] is asked to collect all its data, which in turn will trigger the Slider to solve itself (it got expired in step 4 remember?). This is not a tricky operation, it merely copies the slider value into the slider data structure and shouts "DONE!".
11) [x] then collects the number, stores it into its own data structure and returns priority to the [VB Step 1] object.
12) [VB Step 1] now has sufficient data to get started, so it will trigger the script inside of it. When the script completes, the component is all ready and it will tell the parent document it can move on to the next object (the iteration loop from step 7).
13) Let us assume that the slider object is next on the list, but since it has already been solved (it was solved because [VB Step 1] needed the value) it can be skipped right away, which leaves us with the last object in the document which is still unsolved.
14) [VB Step 2] will be triggered by the document in very much the same way as [VB Step 1] was triggered in step 9. It will also start by collecting all input data.
15) Since all the input data for [VB Step 2] is either defined locally or provided by an object which has already been solved, this process is now swift and simple.
16) Upon collecting all data and running the user script, the component will surrender priority and the document becomes active again.
17) The document triggers a redraw of the Grasshopper Canvas and the Rhino viewports and then surrenders priority again and so on and so forth all the way up the hierarchy until Grasshopper becomes idle again.
[end boring]
Pretty involved for a small 3-component setup, but there you have it.
To answer somewhat more directly your questions:
- The order in which objects are solved is the same as the order in which they are drawn. This is only the case at present, this behaviour may change in the future.
- Adding a delay will not solve anything, since the execution of all components is serial, not parallel. Adding a delay simply means putting everything on hold for N milliseconds.
- [VB Step 1] MUST be solved prior to [VB Step 2] because otherwise there'd be no data to travel from [GO] to [Activate]. The only tricky part here is that sometimes [VB Step 1] will be solved as part of the process of [VB Step 2], while at other times it may be solved purely on its own merits. This should not make a difference to you as it does not affect the order in which your scripts are called.
--
The Man from Scene 24…
Added by David Rutten at 4:43pm on December 10, 2009
. From the Thermal Comfort Indices component, Comfort Index 11 (TCI-11):MRT = f(Ta, Tground, Rprim, e)
with:- Ta = DryBulbTemperature coming from ImportEPW component- Tground = f(Ta, N) where N comes from totalSkyCover input. Tground influences the long-wave radiation emitted by the ground in the MRT calculation.- Rprim defined as solar radiation absorbed by nude man = f(Kglob, hS1, ac)- ac is the clothingAlbedo in % (bodyCharacteristics input)- I can't find any definition in the code of Kglob and hS1. Could you tell me please what are those values referencered to? --> probably the globalHorizontalRadiation but how?- e = vapour pressure calculated from Ta and Relative Humidity input
Do you agree that in this case the MRT does not depend on these inputs: location, meanRadiantTemperature, dewPointTemperature and wind speed?It does not depend neither on the other bodyCharacteristics like bodyPosture, age, sex, met, activityDuration...?
MRT calculated by the TCI-11 method is the mean radiant temperature of a vector pointing vertically with a sky view factor of 100%?For ParisOrly epw,
2. From the SolarAdjustedTemperature component (that seems to be more used for the UTCI calculation examples on Hydra compared to TCI-11).
In contrast to the TCI-11, this component distinguishes diffuse and direct radiation and contextualizes the calculation thanks to _ContextShading input, right? It can also be applied to a mannequin thanks to the CumSkyMatrix and thus evaluate the dishomogeneity of radiation exposure.This component seems not to consider the influence of vapour pressure on the result --> is it then more precise to put the MRT output (from the TCI) as an input of meanRadTemperature for SolarAdjustedTemperature?The default groundReflectivity is set to 0.25 --> is GroundReflectivity taken into account in the Tground or MRT calculation in the TCI component? If yes, what is the hypothesised groundReflectivity?The default clothing albedo of 37% (TCI-11 bodyCharacteristics) corresponds to Clothing Absorptivity of 63%?
If the CumSkyMatrix input is not supplied, I get 9 results for the mannequin --> where are those points/results coming from?
If the CumSkyMatrix input is supplied,I suppose the calculation of the 482 results correspond to a calculation method similar to the radiation analysis component that is averaged over the analysis period. Right?But I don't understand why the mannequin is composed of 481 faces and meshFaceResult gives 482 results.
Finally, what is the link between the MESH results, the solarAdjustedMRT and the Effective Radiant field ? Is there a paper to have a detailed explanation of the method?
3. Here are some results for the ParisOrly energyplus weather data. You can find here attached the grasshopper definition.There is no shading in this simulation and the result coming from the ThermalComfort indices for MRT is very different compared to the solar adjusted MRT.Why such a big difference and which of the result should be plugged into the UTCI calculation component?
Results for ParisOrly.epwM,D,H:1,1,12
Ta : 6.5°Crh: 100%globalHorizontalRadiation: 54 Wh/m2totalSkyCover: 10MRT (TCI-11): 1.2°C
_CumSkyMtxOrDirNormRad = directNormalRadiation : 0 Wh/m2diffuseHorizontalRad: 54 Wh/m2_meanRadTemp = TasolarAdjustedMRT: 10.64°CMRTDelta: 4.14°C
_CumSkyMtxOrDirNormRad = CumulativeSkyMtxdiffuseHorizontalRad: 54 Wh/m2_meanRadTemp = TasolarAdjustedMRT: 10.47°CMRTDelta: 3.97°C
_CumSkyMtxOrDirNormRad = CumulativeSkyMtxdiffuseHorizontalRad: 54 Wh/m2_meanRadTemp = MRT (TCI-11)solarAdjustedMRT: 5.17°CMRTDelta: 3.97°C
Thanks a lot for your helpRegards,
Aymeric
…
as one element.
Thank you
Comment by karamba on October 7, 2014 at 11:27pm
Hello Patricio, divide the beams in such a way that each boundary vertex of the shell becomes an endpoint of a beam segment.
Best, Clemens
Comment by Llordella Patricio on October 8, 2014 at 8:30amDelete Comment
Hi Clemens,
I did what you suggested but now assemble element doesn´t work properly. Could you please tell me how to fix it? Thanks in advance, Patricio
8-10-14losa%20cadena.gh
Comment by karamba on October 8, 2014 at 11:59am
Hi Patricio, if you flatten the 'Elem'-input at the 'Assemble'-component the definition works. The triangular shell elements have linear displacement interpolations whereas the beam deflections are exact. In order to get correct results you should refine the shell mesh.
Best, Clemens
Comment by Llordella Patricio on October 9, 2014 at 8:35amDelete Comment
Hello, succeeds in creating the mesh to the slab, and built the beam segment, but when I see the deformations are not expected because the beam is deformed as the slab.
Thanks for the help
PS: maybe I'm using the program for a type of structure that is not the most appropriate, as I saw in the examples of other structures. But this type of structure is that students taught
best regards
Patricio
9-10-14%20Example%201.gh
Comment by karamba on October 9, 2014 at 10:46am
You could use the 'Mesh Edges'-component to retrieve the naked edges and turn them into beams - see attached file:91014Example1_cp.gh
Best regards,
Clemens
Comment by Llordella Patricio on October 15, 2014 at 3:41pmDelete Comment
Dear clemens
I was doing a rough estimate of the deformation, and I can not achieve the same result with Karamba. When I make a rough estimate of the result with Karamba beams and mine are very similar, I think the problem is when I connect the shell, because there are no similar results.
I sent the GH file, and an image of the calculation
The structure is concrete The result I get is 0.58cm
thank youPatricio
15-10-14%20Example.gh
Comment by karamba yesterday
Dear Patricio,
try to increase the number of shell elements. As mentioned in the manual they are linear elements. A mesh that is too coarse leads to a response which is stiffer than the real structure.
Best,
Clemens
…
rring to the above image)
Area
effective
effective
Second
Elastic
Elastic
Plastic
Radius
Second
Elastic
Plastic
Radius
of
Vy shear
Vz shear
Moment
Modulus
Modulus
Modulus
of
Moment
Modulus
Modulus
of
Section
Area
Area
of Area
upper
lower
Gyration
of Area
Gyration
(strong axis)
(strong axis)
(strong axis)
(strong axis)
(strong axis)
(weak axis)
(weak axis)
(weak axis)
(weak axis)
A
Ay
Az
Iy
Wy
Wy
Wply
i_y
Iz
Wz
Wplz
i_z
cm2
cm2
cm2
cm4
cm3
cm3
cm3
cm
cm4
cm3
cm3
cm
I have a very similar table which I could import to the Karamba table. But I have i_v or i_u values as well as radius of inertia for instance.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
dimensjon
Masse
Areal
akse
Ix
Wpx
ix
akse
Iy
Wpy
iy
akse
Iv
Wpv
iv
Width
Thickness
Radius R
[kg/m]
[mm2]
[mm4]
[mm3]
[mm]
[mm4]
[mm3]
[mm]
[mm4]
[mm3]
[mm]
[mm]
[mm]
[mm]
L 20x3
0.89
113
x-x
4,000
290
5.9
y-y
4,000
290
5.9
v-v
1,700
200
3.9
20
3
4
L 20x4
1.15
146
x-x
5,000
360
5.8
y-y
5,000
360
5.8
v-v
2,200
240
3.8
20
4
4
L 25x3
1.12
143
x-x
8,200
460
7.6
y-y
8,200
460
7.6
v-v
3,400
330
4.9
25
3
4
L 25x4
1.46
186
x-x
10,300
590
7.4
y-y
10,300
590
7.4
v-v
4,300
400
4.8
25
4
4
L 30x3
1.37
175
x-x
14,600
680
9.1
y-y
14,600
680
9.1
v-v
6,100
510
5.9
30
3
5
L 30x4
1.79
228
x-x
18,400
870
9.0
y-y
18,400
870
9.0
v-v
7,700
620
5.8
30
4
5
L 36x3
1.66
211
x-x
25,800
990
11.1
y-y
25,800
990
11.1
v-v
10,700
760
7.1
36
3
5
L 36x4
2.16
276
x-x
32,900
1,280
10.9
y-y
32,900
1,280
10.9
v-v
13,700
930
7.0
36
4
5
L 36x5
2.65
338
x-x
39,500
1,560
10.8
y-y
39,500
1,560
10.8
v-v
16,500
1,090
7.0
36
5
5
I have diagonals (bracings) which can buckle in these "non-regular" directions too, and they do. If I could add those values then in the Karamba model I could assign specific buckling scenarios..... I can see another challenge which will be at the ModifyElement component, I will not be able to choose these buckling lengths, in these directions.
Do you think this functionality can be added within short, or should I try to find another way to model these members?
Br, Balazs
…
1 JUN to 31 DECBetween hours 1:00 to 24:00Current document units is in MetersConversion to Meters will be applied = 1.000[1 of 7] Writing simulation parameters...Ground temperature data contains monthly average temperatures at 3 different depths .5 meters (1st)2 meters (2nd)4meters (3rd)respectively[2 of 6] No context surfaces...[3 of 6] Writing geometry...[4 of 6] Writing materials and constructions...[5 of 7] Writing schedules...[6 of 7] Writing loads and ideal air system...[7 of 7] Writing outputs......... idf file is successfully written to : c:\ladybug\unnamed\EnergyPlus\unnamed.idf
Analysis is running!...c:\ladybug\unnamed\EnergyPlus\eplusout.csv......
Done! Read below for errors and warnings:
Program Version,EnergyPlus, Version 8.3.0-6d97d074ea, YMD=2015.05.24 11:32,IDD_Version 8.3.0
** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
** Warning ** Version: in IDF="'8.1.0'" not the same as expected="8.3"
************* Beginning Zone Sizing Calculations
** Severe ** GetSurfaceData: Some Outward Facing angles of subsurfaces differ significantly from base surface.
** ~~~ ** ...use Output:Diagnostics,DisplayExtraWarnings; to show more details on individual surfaces.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW3 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW3 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=EW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=EW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=0.9038)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=0.9038)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=16.0967)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=16.0967)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 6 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 7 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 8 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 9 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 5 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 6 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 7 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 8 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW6 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW6 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=EW0 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=EW0 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=1.4709)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=1.4709)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=15.6696)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=15.6696)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=FLOOR is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=FLOOR is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=CIELING is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=CIELING is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Warning ** ManageSizing: For a plant sizing run, there must be at least 1 Sizing:Plant object input. SimulationControl Plant Sizing option ignored.
************* Testing Individual Branch Integrity
************* All Branches passed integrity testing
************* Testing Individual Supply Air Path Integrity
************* All Supply Air Paths passed integrity testing
************* Testing Individual Return Air Path Integrity
************* All Return Air Paths passed integrity testing
************* No node connection errors were found.
************* Beginning Simulation
************* Simulation Error Summary *************
** Warning ** The following Report Variables were requested but not generated
** ~~~ ** because IDF did not contain these elements or misspelled variable name -- check .rdd file
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=CHILLER ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=BOILER HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=FAN ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE VENTILATION FAN ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE VENTILATION TOTAL HEAT LOSS ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE VENTILATION TOTAL HEAT GAIN ENERGY, Frequency=Hourly
************* There are 1 unused schedules in input.
************* There are 1 unused week schedules in input.
************* There are 3 unused day schedules in input.
************* Use Output:Diagnostics,DisplayUnusedSchedules; to see them.
************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
************* EnergyPlus Sizing Error Summary. During Sizing: 1 Warning; 49 Severe Errors.
************* EnergyPlus Completed Successfully-- 4 Warning; 49 Severe Errors; Elapsed Time=00hr 00min 4.59sec
Thanks Abraham.I really appreciate it.
Another thing ' I posted a discussion few days ago and got no replies.And this forum is the only 'Hope' for me..Can you quickly check it?thanks.
N
http://www.grasshopper3d.com/group/ladybug/forum/topics/free-form-external-wall-with-glazing-workflow?xg_source=activity
…
Introduction to Grasshopper Videos by David Rutten.
Wondering how to get started with Grasshopper? Look no further. Spend an some time with the creator of Grasshopper, David Rutten, to learn the