EC
1. Between hours 1:00 to 24:002. Current document units is in Meters3. Conversion to Meters will be applied = 1.0004. [1 of 7] Writing simulation parameters...5. [2 of 6] No context surfaces...6. [3 of 6] Writing geometry...7. [4 of 6] Writing materials and constructions...8. [5 of 7] Writing schedules...9. [6 of 7] Writing loads and ideal air system...10. [7 of 7] Writing outputs...11. ...... idf file is successfully written to : c:\ladybug\Freeformtower_IDF\EnergyPlus\Freeformtower_IDF.idf12. 13. Analysis is running!...14. ......
Done! Read below for errors and warnings:
15. 16. Program Version,EnergyPlus-Windows-64 8.1.0.009, YMD=2015.04.04 23:39,IDD_Version 8.1.0.00917. 18. ************* IDF Context for following error/warning message:19. 20. ************* Note -- lines truncated at 300 characters, if necessary...21. 22. ************* 577 Zone,23. 24. ************* Only last 1 lines before error line shown.....25. 26. ************* 578 Freeformbuilding27. 28. ** Warning ** IP: IDF line~578 Comma being inserted after:" Freeformbuilding" in Object=ZONE29. 30. ** Severe ** Out of range value Numeric Field#5 (Type), value=0.00000, range={>=1 and <=1}, in ZONE=FREEFORMBUILDING31. 32. ************* IDF Context for following error/warning message:33. 34. ************* Note -- lines truncated at 300 characters, if necessary...35. 36. ************* 586 BuildingSurface:Detailed,7341.
…
cture, Rhino treats them as a single flat list. For example a surface can have 10 rows and 6 columns of control-points, resulting in a list of 60 points.
But 10 times 6 isn't the only way to get to 60. If you want to make a surface out of a list of 60 points, you'll also have to tell Rhino how those 60 points should be interpreted in terms of a grid. It could be 2*30, 3*20, 4*15, 5*12, 6*10, and all of the aforementioned products the other way around.
Sometimes there's only one way for a number of points to fit into a rectangular grid. For example if you provide 49 points, then 7*7 is the only way to make it work, but these cases are rare so we always demand you give us all the information required to actually make a rectangular grid of control-points from a linear collection.
As for "Why is it, sometimes we need to attach additional value into it?", this is usually because when you divide a domain or a curve into N segments, you end up with N+1 points. For example take the domain {0 to 5}, and divide it into 5 equal subdomains. You end up with {0 to 1}, {1 to 2}, {2 to 3}, {3 to 4} and {4 to 5}. However there are six numbers that mark the transitions between these domains 0, 1, 2, 3, 4 and 5. This is why you often have to add 1 to the UCount, because the number that controls the UCount often results in N+1 actual points.…
Added by David Rutten at 8:30am on December 25, 2014
and Ronnie of StudioMode and David Fano of DesignReform will also be attending.
RSVP has been closed on this event. Space is limited to 50 people. Please attend if you do RSVP.
Agenda -
12:00-1:00 Arrival, informal discussion
1:00 - 1:15 Introductions
1:15 - 2:00 Project presentation 1 (30 minutes + 15 min QA) - David Lee - Clemson - 3D pattern environments using volumetric proxies.
2:00 - 2:45 Project Presentation 2 (30 minutes + 15 min QA) - P. Casey Mahon - Organic Abstractions (30 minutes + 15 min QA)
2:45 - 3:45 David Rutten - New work in GH (30 min QA)
3:45 - 4:30 Sameer Kumar AIA - KPF - Project presentation 3 (30 minutes + 15 min QA)
4:30 - 5:15 Chris Wilkins - Clemson - Urban Renewal and parametric urban development studies in Grasshopper.
5:15 - 6:00 David Rutten - Scripting in GH (15 min QA)
After 6:00 conversations may move down the street for more discussion.
If you would like to present your project at the Cloud please email: scottd@mcneel.com…
53 → 53 → 63 → 74 → 74 → 84 → 9
As you can see from the above list the connection sequence comes in waves of three, where each group of similar indices on the left is associated with a group of three incrementing indices on the right.
Some combination of Series components will probably generate this list, but it'll only work for the first ring, the second one will need a different connection pattern. It is perhaps better to just encode the integer pairs by hand. But then you cannot change your mind about the number of sides later.…
Added by David Rutten at 10:39am on October 21, 2015
4, 3, 7, 7, 7, 8
would need to be
5, 6, 7, 8, 4, 3, 7, 8
ideas?
current workaround (kangaroo dupPt component) removes all duplicates from list, tho does maintain order.
thx…
13 5 15 6 17 7 ... …
But it seems I have not been clear:
the input values (3,5,7,9,11,13) should be presented in the way of "number slider" parameter. So by increasing the value of the slider from minimum 3, to 5, 7, 9, 13, 15, 17... I should get an output numbers of 0,1,3,4,5,6,7...
So I if choose value 3 on the input "number slider", on the other end, I want 0 as an output.
Or if I choose value 5 on the input "number slider", I want 1 as an output, and so on.
Is this possible?…
shift. I realize I can use 'replace branch' but I do not have an available mask to utilize. I have simplified the problem to its simplest form so my question is understandable, however, the tree I am trying perform this operation on is a much larger 3 digit path address.
{1;3;2}
{2;3;4}
{3;5;4}
{4;3;7}
Change the above list to the list below.
{0;3;2}
{1;3;4}
{2;5:4}
{3;3;7}
I wish for a more robust arsenal of branch manipulation components. Most of the things I need to do are possible with the existing components, however, many operations take several components to perform even simple manipulations. Since branch/path manipulation is so integral to using GH successfully, it seems the GH community would be well served by enhancing the available path manipulation components.
Thanks,
Stan
…