etc.
Group 2 - 1, 6, 11, 16, 21 etc.
Group 3 - 2, 7, 12, 17, 22 etc.
Group 4 - 3, 8, 13, 18, 23 etc.
Group 5 - 4, 9, 14, 19, 24 etc. "
except in data, the branches start at 0, so 'group 1' is branch 0
as for the order of your points, that depends on the input prior sorting...
yrs …
EC
1. Between hours 1:00 to 24:002. Current document units is in Meters3. Conversion to Meters will be applied = 1.0004. [1 of 7] Writing simulation parameters...5. [2 of 6] No context surfaces...6. [3 of 6] Writing geometry...7. [4 of 6] Writing materials and constructions...8. [5 of 7] Writing schedules...9. [6 of 7] Writing loads and ideal air system...10. [7 of 7] Writing outputs...11. ...... idf file is successfully written to : c:\ladybug\Freeformtower_IDF\EnergyPlus\Freeformtower_IDF.idf12. 13. Analysis is running!...14. ......
Done! Read below for errors and warnings:
15. 16. Program Version,EnergyPlus-Windows-64 8.1.0.009, YMD=2015.04.04 23:39,IDD_Version 8.1.0.00917. 18. ************* IDF Context for following error/warning message:19. 20. ************* Note -- lines truncated at 300 characters, if necessary...21. 22. ************* 577 Zone,23. 24. ************* Only last 1 lines before error line shown.....25. 26. ************* 578 Freeformbuilding27. 28. ** Warning ** IP: IDF line~578 Comma being inserted after:" Freeformbuilding" in Object=ZONE29. 30. ** Severe ** Out of range value Numeric Field#5 (Type), value=0.00000, range={>=1 and <=1}, in ZONE=FREEFORMBUILDING31. 32. ************* IDF Context for following error/warning message:33. 34. ************* Note -- lines truncated at 300 characters, if necessary...35. 36. ************* 586 BuildingSurface:Detailed,7341.
…
53 → 53 → 63 → 74 → 74 → 84 → 9
As you can see from the above list the connection sequence comes in waves of three, where each group of similar indices on the left is associated with a group of three incrementing indices on the right.
Some combination of Series components will probably generate this list, but it'll only work for the first ring, the second one will need a different connection pattern. It is perhaps better to just encode the integer pairs by hand. But then you cannot change your mind about the number of sides later.…
Added by David Rutten at 10:39am on October 21, 2015
ouldn't the surface component only accept the number 8? it accepts 5 and 7. the grid is 7 points in the x direction and 5 points in the y direction. so shouldn't the u count be either 6 or 8?
it works with the u count at 5. i just don't understand why.
thank you so much for your patience with my questions.
…
Added by pwdarden to gHowl at 6:18pm on September 21, 2013
ersect (2, 3, 4, 5, 6) with the line and the ones which do not intersect (0, 1, 7). Intersect is done! But how to get the non intersecting vectors (0, 1, 7)?
So I e. g. could deselect vectors 2, 3, 4, 5, 6 so I would display/use only vectors 0, 1, 7 and the bounced ones.
Appreciate your help!
Rudi…