13 5 15 6 17 7 ... …
But it seems I have not been clear:
the input values (3,5,7,9,11,13) should be presented in the way of "number slider" parameter. So by increasing the value of the slider from minimum 3, to 5, 7, 9, 13, 15, 17... I should get an output numbers of 0,1,3,4,5,6,7...
So I if choose value 3 on the input "number slider", on the other end, I want 0 as an output.
Or if I choose value 5 on the input "number slider", I want 1 as an output, and so on.
Is this possible?…
EC
1. Between hours 1:00 to 24:002. Current document units is in Meters3. Conversion to Meters will be applied = 1.0004. [1 of 7] Writing simulation parameters...5. [2 of 6] No context surfaces...6. [3 of 6] Writing geometry...7. [4 of 6] Writing materials and constructions...8. [5 of 7] Writing schedules...9. [6 of 7] Writing loads and ideal air system...10. [7 of 7] Writing outputs...11. ...... idf file is successfully written to : c:\ladybug\Freeformtower_IDF\EnergyPlus\Freeformtower_IDF.idf12. 13. Analysis is running!...14. ......
Done! Read below for errors and warnings:
15. 16. Program Version,EnergyPlus-Windows-64 8.1.0.009, YMD=2015.04.04 23:39,IDD_Version 8.1.0.00917. 18. ************* IDF Context for following error/warning message:19. 20. ************* Note -- lines truncated at 300 characters, if necessary...21. 22. ************* 577 Zone,23. 24. ************* Only last 1 lines before error line shown.....25. 26. ************* 578 Freeformbuilding27. 28. ** Warning ** IP: IDF line~578 Comma being inserted after:" Freeformbuilding" in Object=ZONE29. 30. ** Severe ** Out of range value Numeric Field#5 (Type), value=0.00000, range={>=1 and <=1}, in ZONE=FREEFORMBUILDING31. 32. ************* IDF Context for following error/warning message:33. 34. ************* Note -- lines truncated at 300 characters, if necessary...35. 36. ************* 586 BuildingSurface:Detailed,7341.
…
tName_FinalProject_PartD.pdf
Below is the desk crit list, please sign up for a spot in the comments below:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
See you Monday!…
ta.
Take the following example.
I have two curves referenced with a Crv Param this creates a single path with 2 items {0}(N=2).
If I divide these Curves by 10 segments I end up with 2 Paths of 11 points each {0;0}(N=11) and {0;1}(N=11)
If I want each point to be handled separately I can Graft a branch to hold each point. So I get 22 Paths looking like {0;0;0}(N=1), {0;0;1}(N=1).....{0;1;10}(N=1).
Each path is therefore the address of a particular item or items of interest.
The Param Viewer can be found Params>Special>Param Viewer and can be viewed either as a list of Paths or graphically by a double click.
Also note that the Fancy Wires display the structure of a stream of data. Single wire = Single Data Item, Double Wire = Multiple Data on single Path and Double Dashed Wire = Multiple/Single Data on Multiple Paths…
ents will do or which components will be available.
My problem arises because I want to obtain a list such as the following:
{{6, 5, 4, 3, 2, 1, 2, 3, 4, 5, 6}, {5, 6, 5, 4, 3, 2, 1, 2, 3, 4, 5}, {4, 5, 6, 5, 4, 3, 2, 1, 2, 3, 4}, {3, 4, 5, 6, 5, 4, 3, 2, 1, 2, 3}, {2, 3, 4, 5, 6, 5, 4, 3, 2, 1, 2}, {1, 2, 3, 4, 5, 6, 5, 4, 3, 2, 1}}
Which displayed as a matrix is:
If it were possible to combine GH operations (series, shift list, replace string...) with matrices I think it would be quite powerful. A matrix to list component like those available on scientific calculators, would then translate the matrix to list.
For me, matrices come in handy when dealing with surface patterns.
…
Added by Jesus Galvez at 6:46am on November 26, 2012