rve
10 curve
11 curve
12 curve
13 curve
...and I'd like to rearrange the order in which the curve are listed, to something like this:
{0,0,0}
0 curve
1 curve
8 curve
9 curve
10 curve
11 curve
2 curve
3 curve
4 curve
5 curve
12 curve
13 curve
6 curve
7 curve
I hope this makes sense.
Thank in advance for any advice,
John…
0,
I want to move everything in {2} up 5 and 10 and 15,
Any ideas. I have been trying using the series component to create the right data structure but somehow its not working and i am sure there is a simple way?
Do i have to repeat the data so that the number of transform data matches the input list or is there a way to simply apply the transformation to everything in {0}{1} and {2} respectively depending on its structure ??
Hopefully this makes sense? I am not really sure but is it a job for stream - i cant understand why i cant get it to work. Sorry i am sure this is covered in the forums, i have been looking but cant anything which helps specifically.
Many thanks
Chris…
s 8, 4, 2, 10, 1, 3, 8, 4, 2, 0. But then for the end result to maintain all numbers above 5 but replace all numbers below with a defined number..Let's say zero. So then the list would read...8, 0, 0, 10, 0, 0, 8, 0, 0.…
vector * number
8. number * point
9. point * number
10. complex * complex
11. colour * colour
12. colour * number
13. number * colour
--
David Rutten
david@mcneel.com
Seattle, WA…
Added by David Rutten at 10:39pm on November 12, 2010
cture, Rhino treats them as a single flat list. For example a surface can have 10 rows and 6 columns of control-points, resulting in a list of 60 points.
But 10 times 6 isn't the only way to get to 60. If you want to make a surface out of a list of 60 points, you'll also have to tell Rhino how those 60 points should be interpreted in terms of a grid. It could be 2*30, 3*20, 4*15, 5*12, 6*10, and all of the aforementioned products the other way around.
Sometimes there's only one way for a number of points to fit into a rectangular grid. For example if you provide 49 points, then 7*7 is the only way to make it work, but these cases are rare so we always demand you give us all the information required to actually make a rectangular grid of control-points from a linear collection.
As for "Why is it, sometimes we need to attach additional value into it?", this is usually because when you divide a domain or a curve into N segments, you end up with N+1 points. For example take the domain {0 to 5}, and divide it into 5 equal subdomains. You end up with {0 to 1}, {1 to 2}, {2 to 3}, {3 to 4} and {4 to 5}. However there are six numbers that mark the transitions between these domains 0, 1, 2, 3, 4 and 5. This is why you often have to add 1 to the UCount, because the number that controls the UCount often results in N+1 actual points.…
Added by David Rutten at 8:30am on December 25, 2014
Dimitris,
You need to set your occupancy from 0 to 9 (say it is 1), then from 9:01 (or 10) to 17:59 set it to 0 and from 18 to 24 set it back to 1 again. This is how you set schedules in E+.
-A.
ll these 12500 points.
Group 1 would represent the point located at 0, 5, 10, 15, 20 etc.
Group 2 - 1, 6, 11, 16, 21 etc.
Group 3 - 2, 7, 12, 17, 22 etc.
Group 4 - 3, 8, 13, 18, 23 etc.
Group 5 - 4, 9, 14, 19, 24 etc.
I can create the pattern but the selection of points are all the points in row 0 and then all the points in row 5 and so on.
I would like the selection of points to start at the bottom left, and sequentially continue to the right and then continue on the 2nd row (left to right & bottom to top). i am hoping the pattern i am trying to achieve is more understood with the quick screen capture I uploaded.
the end goal is to be able to select all the points in the grid that are in each pattern.
Thanks in advance for any guidance with this. …
Added by Alyne Rankin at 6:53am on October 11, 2017
en 3 of them, and one poolyline between two of them.
It would also be very nice if i could control it so that only the successive ones can be connected
so if {0:0:0} has 8 points and {0:0:1} has 8, as do {0:0:5} and {0:0:6} i would like to have this as two polylines, not one continoous that would in this case jump three branches (or curves that are shorter).
Does this make any sense?…
Added by Dusan Bosnjak at 2:08pm on September 28, 2009
)
3. KeyError(1417,)
4. KeyError(1417,)
5. KeyError(1417,)
6. KeyError(1417,)
7. KeyError(1417,)
8. KeyError(1417,)
9. KeyError(1417,)
10. KeyError(1417,)
11.......
i tried different weather file but also same result. it seems i have same problem. the file am working on is the radiation file i took from the examples . whats seems to be the problem?
thank you for your time…