ve it) rotated by 15, group 3 ( above group 2) rotated 15 degrees relative to group 2.
The distance between the cubes, the number of cubes on each contour must remain as shown in attached gh file.
I understand we can achieve this with series or with shift, however am unable to figure out where to plug it in to achieve the desired result.
Please guide.
Many Thanks…
Dim S As New NurbsSurface
Dim k1 As New Integer Dim k2 As New Integer Dim k3 As New Integer
Dim pt_2 As New point3d Dim pt_3 As New point3d Dim pt_4 As New point3d
k1 = 13 k2 = 14 k3 = 15
For i As Integer = 0 To 7 If k1 > 15 Then k1 = k1 - 15 End If pt_2 = L_pts(k1)
If k2 > 15 Then k2 = k2 - 15 End If pt_3 = L_pts(k2)
If k3 > 15 Then k3 = k3 - 15 End If pt_3 = L_pts(k3)
S = nurbsSurface.CreateFromCorners(centre, pt_2, pt_3, pt_4) TAB.add(S)
k1 = k1 + 3 k2 = k2 + 3 k3 = k3 + 3
Next
A = S
You dont realy need to understand the script but I want to be able to declare a dim as a Surface and on the core creat different surface from 4 pt.
Thanks for your Help,
Best regards,
Renaud Ganière…
s (i. e. 5) and circles (i. e. 3). I find the closest points from the given point to the circles and I draw the lines between those (so I hace 15 points, 3 for each point). What I need now is to Grasshopper to select the longest (or the shortest) of each three lines.
Any sugestions..
(attahfed you'll see the Rhino file)
Thanks a lot fellows. Any help I'll apprreciate a lot.…
x and min values for x,y,z and calculate energy for each optionand collect these results in excel sheet ...
option No. x y z Annual coiling demand(by DIva)
1 10 10 10
2 10 15 20
3 11 10 19
4 12 14 17
5 15 16 15
6 16 11 14
7 18 12 12
.
.
etc
Regards ...
hossam
Hossam.wefki@gmail.com…
If you consider laptops as something to be changed every 3 years like me: go for the Asus N550J series. i7 @2.4Ghz + 16Go RAM + nice screen + 7200RPM disk. 15 or 17", and a nice design. 1000-1300€.
it,
[3] the upper limit, [4] the slider position.
What do you think?
Matt
Radlab, Incorporated
25 Drydock Ave, Floor 6
Boston, MA 02210
W| radlabinc dot com
E| matt@radlabinc
P| 617.440.3588…
Added by Matt Trimble at 7:54pm on November 17, 2009
mputer... so 1 seems strange. Also, the serial port is closed, so you wont be able to control your steppers until you open the port. Lastly, the Stepper Motor component also has to have the Start toggle set to true before actually sending values to the board. Hopefully that helps.…
nd this is the error text:
0. Current document units is in Meters1. Conversion to Meters will be applied = 1.0002. [1 of 8] Writing simulation parameters...3. [2 of 8] No context surfaces...4. [3 of 8] Writing geometry...5. [4 of 8] Writing Electric Load Center - Generator specifications ...6. [5 of 8] Writing materials and constructions...7. [6 of 8] Writing schedules...8. [7 of 8] Writing loads and ideal air system...9. [8 of 8] Writing outputs...10. ...... idf file is successfully written to : C:\Users\Pier\Desktop\Dottorato\Energy_plus_file\cell room\EnergyPlus\cell room.idf11. 12. Analysis is running!...13. C:\Users\Pier\Desktop\Dottorato\Energy_plus_file\cell room\EnergyPlus\eplusout.csv14. ......
Done! Read below for errors and warnings:
15.
Thanks in advance to all for your help me
Francesco…