byte-accuracy red, green, blue channels) = 27 bytes. More likely 28 bytes as colours are probably stored as 32-bit integers, allowing for an unused alpha channel.
28 * 800,000 equals roughly 22 megabytes, which is way down from 9 gigabytes. That's a 400 fold memory overhead, which is pretty hefty.
Grasshopper stores points as instances of classes, so on 64-bit systems it actually takes 64+64+3*8 = 152 bytes per point*, which adds up to 122MB, still way less than 9GB. It would be interesting to know where all the memory goes...
* Grasshopper points also store reference data, in case they come from the Rhino document. This data will not exist, but even so it will require 64-bits of storage.…
Added by David Rutten at 4:13pm on December 11, 2014
e
7. True
8. True <-- this one
9. True
10. False
11. True
12. False
13. True
14. True <-- this one
15. True
16. False
17. True
18. False
19. True
20. True <-- this one
21. True
22. False
23. True
24. False
25. True
26. True <-- this one
27. True
28. False
29. True
30. False
31. True
32. True <-- this one
33. True
Any idea how I can solve this?
Thanks!…
NONE, in SIZING:PARAMETERS". I'm not sure of where to start in troubleshooting this. I've attached the file.
Thank you,
See the errors and warnings below:
{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. [1 of 8] Writing simulation parameters...
3. [2 of 8] Writing context surfaces...
4. [2 of 8] Writing context surfaces...
5. [3 of 8] Writing geometry...
6. [4 of 8] Writing Electric Load Center - Generator specifications ...
7. [5 of 8] Writing materials and constructions...
8. [6 of 8] Writing schedules...
9. [7 of 8] Writing loads and ideal air system...
10. [8 of 8] Writing outputs...
11. ...
... idf file is successfully written to : R:\Green\SuRG\Building_Performance_Analysis\2016_analysis_studies\Energy_Analysis_Comparison\Honeybee_+_Ladybug\tutorial01\EnergyPlus\tutorial01.idf
12.
13. Analysis is running!...
14. ...
...
Done! Read below for errors and warnings:
15.
16. Program Version,EnergyPlus, Version 8.5.0-c87e61b44b, YMD=2016.10.31 11:39,IDD_Version 8.5.0
17.
18. ************* IDF Context for following error/warning message:
19.
20. ************* Note -- lines truncated at 300 characters, if necessary...
21.
22. ************* 24 Sizing:Parameters,
23.
24. ************* Only last 1 lines before error line shown.....
25.
26. ************* 25 None, !- Heating Sizing Factor
27.
28. ** Severe ** IP: IDF line~25 Invalid Number in Numeric Field#1 (Heating Sizing Factor), value=NONE, in SIZING:PARAMETERS
29.
30. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
31.
32. ** ~~~ ** Possible Invalid Numerics or other problems
33.
34. ** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
35.
36. ...Summary of Errors that led to program termination:
37.
38. ..... Reference severe error count=1
39.
40. ..... Last severe error=IP: IDF line~
, value=NONE, in SIZING:PARAMETERS
41.
42. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
43.
44. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
45.
46. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
47.
48. ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
49.
50. ************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 9.34sec
51.…
ere a way to set this up in a way that lets say when there are 28 it will go for one of 4, 7 or 14 and if it is a primer number it will exclude enough number of boats to obtain the closest suitable number - lets say there are 29 boats but it will only show 28 and go back to selecting 4,7 or 14.…
Added by Levent Ozruh at 10:40am on October 14, 2014
ceros. Parametrización, panelización y análisis en Grasshopper, así como el proceso de manufactura digital para maquinaria de corte Láser y CNC.
UN solo pago anticipado $4,000.00
Pagos diferidos $4,500.00*
*reserva tu lugar con el 50%
Martes y Jueves de 7 a 10 PM
Del 15 de Mayo al 14 de junio
DURACION: 30 HORAS
SESIONES: 10 DE 3 HORAS
o info@dimensiontallerdigital.com
informes al 55 (50 16 0634) con Mayri Gallegos (o al cel. 55 28 85 24 73)
$4,000.00…