Because the Adaptive methodology is founded upon the notion that there are hundreds of social factors that influence comfort and that the best we can do to forecast comfort is to find variables with good correlations to these social factors (like outdoor temperature), the premise that these published Adaptive model holds regardless of cultural norms is dangerous. Notably, the founders of the adaptive model have stressed that this particular linear correlation that you cite comes from recent surveys of buildings where people have both the the ability to open windows AND a great freedom to dress down. Hypothetically, if occupants were able to open the windows in Abraham's building but the cultural norm was that everyone was expected to wear multi-layered suits or dresses (as in historic Britain), a different correlation between outdoor temperature and comfort temperature would exist. In fact, historical European comfort surveys show that people likely preferred cooler temperatures in buildings (about 1-2C cooler) than today's occupants. Accordingly, after recognizing this social premise in the Adaptive model, I have built in a few ways to adjust/alter the version in Ladybug based on the literature I have read (even though these alterations are not a part of any official ASHRAE or European standard).
Abraham, you might have to be a bit more specific about how you would like to adjust the Adaptive comfort model for me to help your particular case and this may lead to me adding in new functionality. For the time being, I can tell you that the 'Ladybug_Adaptive Comfort Parameters' component is going to be your friend and I would recommend using the Adaptive Comfort Chart to visualize how you are changing the model. You can plug these 'Adaptive Comfort Parameters' into the 'Adaptive Comfort Recipe' component to have the microclimate analysis run with these parameters. Here are a few examples of how to alter the model:
1) Mixed-mode Building - Humphreys and the European Adaptive comfort team derived two separate correlations.
One for naturally ventilated buildings:
and conditioned buildings:
The dimensionless value between 0 and 1 for _levelOfConditioning allows you to create different correlations depending on whether occupants have complete freedom of dress and window operability (0) or have slight restrictions like in a mixed mode building (0.5, for example):
2) Changing Response Time of Occupants - There has been a bit of a debate in Literature about whether it is better to use the average monthly temperature or a weekly running mean temperature. The avgMonthORRunningMean input allows you to adjust this like so:
Average Month:
Running Mean:
3) Greater Temperature Range Tolerance - While this last one is actually a part of the European and Adaptive standards, you can adjust the range of the comfort band with either the 'eightyOrNintetyComf' input or the comfortClass input like so:
Ninety Percent Comfortable
Eighty Percent Comfortable
Abraham, let me know if you would like more controls over the model or if this is enough to do what you are thinking of. This example file allows you to construct the images I have above:
http://hydrashare.github.io/hydra/viewer?owner=chriswmackey&fork=hydra_2&id=Adaptive_Comfort_Chart&slide=0&scale=1&offset=0,0
-Chris…
ther math and logic. i can usually conceptualise what i want to do and cobble some semi working thing together but don't know which components to use and how to patch it. so i'm super happy to have someone who knows what he's doing to find this interesting.
and i'm glad you mention the fanned frets again, there is one input parameter that's still missing for the multiscale frets to be fully parametric, it's the angle of the nut or which fret should be straight. it depends a bit on personal preferences and playing posture what is more comfortable. so being able to adjust this easily would be cool. again i have no idea how the maths for that work or if you can just rotate each fret the same amount around it's middle point. The input either as fret number (for the straight fret) or as a simple slider from bridge to nut should do as input setting.
Here are the two extremes and the middle ground:
i've been thinkin today while analysing your patches and cleaning up my mess what exactly the monster should do.
Here are the input parameters needed, i think it's the complete list
scale length low E string
scale length high e string
fret angle/straight fret
string width at nut
string width at bridge
number of frets
fretboard overhang at nut (distance from string to fretboard bounds)
fretboard overhang at last fret
string gauges
string tensions
fretboard radius at nut (for compound radius fretboard radius at bridge is calculated with the stewmac formula)
fretwire crown width
fretwire crown height
action height at nut (distance between bottom of string and fretwire crown top)
action height at last fret
pickup 1 neck position
pickup 2 middle position
pickup 3 bridge position
nut width
the pickup positions should be used to draw circles for the magnet poles on each string so they are perfectly aligned and can be used for the pickup flatwork construction. ideally they would need a rotation control aligning the center line of the pickup so it's somewher between the last fret angle and bridge angle. personally i do this visually depending on the design i'm looking for, some people have huge theories on pickup positioning but personally i don't believe in it.
that should result in everything needed to quickly generate all the necessary construction curves or geometry for nut/fingerboard/frets/pickups. this is the core of what makes a guitar work, the more precise this dynamic system is the better the guitar plays and sounds.
i posted another thread trying to understand how i could use datasets form spreadsheets,databse, csv to organize the input parameters. What would make sense for the strings for example is hook into a spreadsheet with the different string sets, i attached one for the d'Addario NYXL string line which basically covers all combos that make sense.
The string tension is an interesting one, and implmenting it would sure be overkill albeit super interesting to try. it should be possible to extrapolate from the scale length of each string what the tension for a given string gauge of that string would be so that you could say 'i want a fully balanced set' or 'heavy top light bottom) and it would calculate which SKU from d'addario would best match the required tension. All the strings listed in the spreadsheet are available as single strings to buy.
i'm trying to reorganize everything which helps me understand it. i just discovered the 'hidden wires' feature which is great since once i understood what a certain block does or have finished one of my own, i can get the wires out of the way to carry on undistracted. a bit risky to hide so many wires but it makes it so much easier not to get completely lost :-)
btw, the 'fanned fret' term is trademarked, some guy tried to patent it in the 80's which is a bit silly since it has been done for centuries. there is a level of sophistication above this as well, check out http://www.truetemperament.com/ and that really is something else. it really is astounding how superior the tuning is on those wigglefrets, the problem is that it's rather awkward for string bending and also you can't easily recrown or level the frets when they are used. …
me logic produced by running the 2-d voronoi component.
From a given set of polylines we can extract the centers and this can drive both the voronoi component as well as provide the XYZ drill points for the cnc. The definition has a variety of different options. You need Lunchbox, Weaverbird, and Starling. I can't tell you how amazing these 3 tools are from a design perspective. They are extremely powerful so if you don't have these you must install them asap. You can get the tools at http://www.food4rhino.com/
This definition works by first choosing a grid type, next you choose voronoi type, and subdivision type. From the voronoi type list you can choose basic (just grid), truncation (uses truncation calculated via the image sampler), truncation dual (uses the dual of the truncated image based grid), and subdivision (takes the basic grid type and uses different subdivision shcemes). Each of these provide different patterns of polylines from which we can extract our drilling points. I am rather proud of this definition since the overall idea is one which is so simple it's easy to overlook - the idea that drilling with a ball end mill makes voronoi plots. Now when you combine that with all of these amazing tools it can go off right quick. The nice thing is the paatern you see on screen is the pattern that gets made by drilling wysiwyg cnc patterns.
VORONIO_DRILLing.gh
Here are some on screen patterns in process in the following order truncation, basic, subdivision:
here is a video moving over a machined example:
…
l coarse mesh
Subdividing this mesh into strips of thin quads
Relaxing/Planarizing this mesh
Splitting and Unrolling
In this post I deal with the first 2 of these stages.
You can download the example definition here:
developable_strips_tutorial.gh
Drawing the initial mesh
To begin with we need a simple quad mesh. This can be modelled manually in Rhino, and only needs to use enough quads to give the topology and very rough form. No need to worry too much about the exact geometry or dimensions at this point, as we will refine and alter it as we go.
One very important thing that we do need to bear in mind though is that all internal vertices must have even valence (I covered this a bit in the earlier post here).
So for example, this is bad:
(because the highlighted vertex is surrounded by 5 faces)
While this is good (and can still be relaxed to the same shape):
(the top and bottom vertices have valence 8, and the vertices between the arms have valence 4)
With a little practice it should be possible to convert any mesh into one that meets this condition.
The reasons why we need this condition should become more clear in the later steps.
First subdivision
This is where we choose how many strips we want our final model to have, by applying a few rounds of subdivision using the Refine component (you could also use Weaverbird here):
Sorting the face directions
While quad meshes do not carry the same information about u/v directions as a NURBS surface, the individual faces do have a sort of direction given by their vertex ordering. However, these face directions are usually not consistently arranged, especially after subdivision.
The Kangaroo MeshDirection component attempts* to orient all the faces in a mesh so that they match with their neighbours.
For example, before sorting, if we draw a line from the midpoint of the first edge of each face to the midpt of its opposite edge, we might get something like this:
Whereas after sorting, we should get something like this:
*note that I say it attempts to orient the faces consistently. In some cases no valid solution exists, for instance if 3 or 5 faces meet around a vertex, hence the requirement mentioned at the start for even valence vertices.
Directional Subdivision
Now that we have consistent face directions across the mesh, we can apply further subdivision, but this time in one direction only. So we go from roughly square quads to thin rectangles. The idea is that as we apply higher levels of this directional subdivision, the final relaxed result goes towards something semi-discrete. A NURBS surface is fully continuous, and a mesh is fully discrete (made up of separate facets), while this strip model will be smooth in one direction and faceted in the other.
Go to part 2 for the next step of the process
…
eration!
See an example work flow for designing, simulating and analysing a Photovoltaic system below.
Download a Grasshopper and Rhino example file:
https://www.dropbox.com/s/krbszlplj5i40dz/017_HBgeneration%20Rhino%20model.3dm?dl=0
https://www.dropbox.com/s/lxneuzal3mipd2q/017_HBgeneration.gh?dl=0
See a quick introduction and tutorial videos here: https://www.youtube.com/playlist?list=PLrx2KnyhaJ5YXo5hpk8Q9q4Vy99O5IegK
1. Select a building to mount a photovoltaic generator on (seen in Rhino in green).
2. Select a surface within that building to mount a photovoltaic generator on (seen in Rhino in green).
3. Create a Honeybee context surface from that surface.
4. Place a photovoltaic generator on that Honeybee context surface by using the Honeybee generation component. Honeybee_Generator_PV and connecting the context surface to it's input _HBSurfaces. Then you can specify both the performance and the financial data of the photovoltaic generator.
5. Create a Honeybee generation system which consists of the photovoltaic generator in 4. By using the component Honeybee_generationsystem and connecting 4 to its input PVHBSurfaces_. Then you can specify the annual maintenance cost of this system.
6. Run the simulation in Energy Plus by connecting 5. to the input HBGenerators_.
7. Read the results of the simulation:
- The electricity produced by the Honeybee generation system in 5.
- The net purchased electricity of the facility (the Honeybee zone) to which the Honeybee generation system is attached to. This is the electricity consumed by the facility less the electricity generated by the Honeybee generation system.
- The financial costs of the Honeybee generation system; capital, maintenance and replacement costs.
8. Calculate the net present cost of the Honeybee generation system in 5 assuming a 25 year lifetime.
9. Visualise the net present cost.
…
or a couple of thingies.
Pattern.gh
I defined parametrically a triangle which I then smoothed out to become more like a blob shape. After that I created a pretty simple pattern that I had in my mind (costed me a lot of time to make this in GH) and finally wanted to rotate each element as it goes higher . The dispatching part seems to be working pretty slow, so it might need an optimization, but I’m still happy with the result as it shows exactly what I wanted, so this is a minor issue in my case.
I then decided to try tessellating my extrusions. You’ll see the voronoi script which is a blob-group in the same Pattern.gh:
I had an idea of something and started the code from scratch, then decided to watch tutorials and implement the code shown there. I somehow coped to combine my code with this in the tutorials, but since my knowledge of Grasshopper is zero to basic my code seems to be very unoptimized and lagging.. When dragging the sliders, it takes a lot of time to compute the changes, although, I’m working on a 24gigs 6th gen i7 machine. It might also need optimization.
Here comes the first tricky part that I couldn’t sort out in an elegant way neither in Grasshopper nor in Rhino. I want a smooth transition between the wall and the ceiling, so that the voronoi tessellation doesn’t get interrupted. If I was to do it in Rhino I’d make a curve with a filleted edge which I’d then revolve/sweep along a rail.
Pattern.gh:
Second thing is – I’ve defined a shape which I want to rotate at a certain degree as it goes higher, however, I don’t have the knowledge to make this happen automatically and just copy the script over and over again. Is there a chance to somehow “loop” the code and parametrically define the degree of rotation and amount of units in the loop?
Next thing is I want to somehow be able to rotate each “6-storey-building” dependently on its surrounding buildings, so that their “terraces” never overlap. I’m using quotes, since they’re still some silly shapes that have nothing to do with buildings and terraces. The principle has to be something like gear wheels or the so-called rack wheels . There has to be some pace which I could set parametrically, but I’m still unsure how to do that in Grasshopper.
The pre-last thing is that I want to control the height of each “building” based on let’s say a topography. I presume this could be done somehow with height maps or some gradient mapper connected to curvature analysis. Not really sure how something like this would work, but I’ve seen such codes that control height depending on a variable.
The last one is more or less similar to the previous. I want to be able to “dissolve” the pattern that I initially created and make it irregular. I suppose this could be done with attractor curve, but again this is just a guess. Please note that this is a top view and the shapes on the upper-left corner have got more "wings" which means there is more floors in the according building. Let's say the buildings in the upper-left corner are 6-7 floors high, in the middle are 4-5 and to the right they're only 3 floors high.
Sorry for that many questions in a single thread. Please let me know if I have to split them in separate threads. All this information is needed for learning purposes. I’m now preparing myself for my bachelor thesis and try as much things as I could, so that I’ll be ready for the final stage of my bachelor’s degree.
Many thanks in advance! Cheers!…
y from the Rhino model and having the absorption coefficients of the materials that are entered into Pachyderm, why is it not possible to generate a reverberation time diagram, without the need to start any analysis?
MAPPING METHOD: When for example the mapping of the Strenght Index (G) is generated through the "create map" option, succesively I can´t generate any other energy criterion map, but I have to redo the simulation.
Is it a limitation of the software or am I wrong something?
MAPPING METHOD: I kindly wanted to ask what is the difference between minimum and detailed convergence and why the number of reflections order it takes into account for the simulation is not specified. The mapping method take care only of the Raytracing Method or the Image Source too?
MAPPING METHOD: Why is the mapping value that can be exported to Rhino not generated for all the calculation raster points, but maximal only for 100 values?
MAPPING METHOD: This method hasn't been implemented in Grasshopper yet, has it?
RAYTRACING METHOD (Pach:RT): I did a raytracing through the components of GH, using only the Pach_RT, and I had these curious results in terms of time:
RaysCount: 15.000, IS_Order:1 = 5min
RaysCount: 15.000, IS_Order:2 = 12min
RaysCount: 15.000, IS_Order:3 = 3min
RaysCount: 15.000, IS_Order:4 = 8min
RaysCount: 15.000, IS_Order:5 = 3min
Why a raytracing with only 2 order, is more and more extensive than the 3/4 and 5 order?
ANALYSIS RESULT: Would there be a way to export all the results of a simulation, as is done via Odeon, to a .txt list?
I apologize in advance for asking so many questions, I hope you can find the time to answer,
Yours sincerely from Müller-BBM…
3. receiver gets data from sender via input (0) < the data here may be changed in the meantime, for instance if its a double then I would like to add 1 to it.
4. receiver sends data to sender's input(2)
5. go to 1.
VS 2013 studio project folder
SENDER
Public Class loopStart Inherits GH_Component
Dim cnt As Integer
Friend Property counter() As Integer Get Return cnt End Get Set(value As Integer) cnt = value End Set End Property
Dim iData As New GH_Structure(Of IGH_Goo)
Friend Property startData() As GH_Structure(Of IGH_Goo) Get Return iData End Get Set(value As GH_Structure(Of IGH_Goo)) iData = value End Set End Property
Public Sub New() MyBase.New("loopStart", "loopStart", "Start the loop with this one.", "Extra", "Extra") End Sub
Public Overrides ReadOnly Property ComponentGuid() As System.Guid Get Return New Guid("bdf1b60d-6757-422b-9d2d-08257996a88c") End Get End Property
Protected Overrides Sub RegisterInputParams(ByVal pManager As Grasshopper.Kernel.GH_Component.GH_InputParamManager) pManager.AddGenericParameter("Data", "dIn", "Data to loop", GH_ParamAccess.tree) pManager.AddIntegerParameter("Steps", "S", "Number of loops", GH_ParamAccess.item) pManager.AddGenericParameter("<X>", "<X>", "Please leave this one alone, don't input anything.", GH_ParamAccess.tree) pManager.Param(2).Optional = True End Sub
Protected Overrides Sub RegisterOutputParams(ByVal pManager As Grasshopper.Kernel.GH_Component.GH_OutputParamManager) pManager.AddGenericParameter("Data", "dOut", "Data to loop", GH_ParamAccess.tree) End Sub
Public Overrides Sub CreateAttributes() m_attributes = New loopStartAttributes(Me) End Sub
Protected Overrides Sub SolveInstance(ByVal DA As Grasshopper.Kernel.IGH_DataAccess)
Dim numLoop As Integer DA.GetData(1, numLoop)
Dim loopDt As New Grasshopper.Kernel.Data.GH_Structure(Of IGH_Goo)
If cnt = 0 Then Me.startData.Clear() DA.GetDataTree(0, Me.startData) loopDt = startData.Duplicate DA.SetDataTree(0, loopDt) End If
If cnt < numLoop - 1 And cnt > 0 Then DA.GetDataTree(2, loopDt) DA.SetDataTree(0, loopDt) Me.ExpireSolution(True) Else DA.GetDataTree(2, loopDt) DA.SetDataTree(0, loopDt) End If
cnt += 1
End Sub
End Class
RECEIVER
Public Class loopEnd Inherits GH_Component
Dim aData As New GH_Structure(Of IGH_Goo)
Friend Property anyData() As GH_Structure(Of IGH_Goo) Get Return aData End Get Set(value As GH_Structure(Of IGH_Goo)) aData = value End Set End Property
Public Sub New() MyBase.New("loopEnd", "loopEnd", "End the loop with this one.", "Extra", "Extra") End Sub
Public Overrides ReadOnly Property ComponentGuid() As System.Guid Get Return New Guid("3ffa3b66-8160-4ab3-87c9-356b2c17aadd") End Get End Property
Protected Overrides Sub RegisterInputParams(ByVal pManager As Grasshopper.Kernel.GH_Component.GH_InputParamManager) pManager.AddGenericParameter("Data", "dIn", "Data to loop", GH_ParamAccess.tree) End Sub
Protected Overrides Sub RegisterOutputParams(ByVal pManager As Grasshopper.Kernel.GH_Component.GH_OutputParamManager) pManager.AddGenericParameter("Data", "dOut", "Data after the loop", GH_ParamAccess.tree) End Sub
Protected Overrides Sub SolveInstance(ByVal DA As Grasshopper.Kernel.IGH_DataAccess) Me.aData.Clear() DA.GetDataTree(0, Me.aData) runner()
DA.SetDataTree(0, Me.aData) End Sub
Sub runner()
Dim doc As GH_document = Grasshopper.Instances.ActiveCanvas.Document Dim docl As list(Of iGH_DocumentObject) = (doc.Objects)
For i As Integer = 0 To docl.count - 1 Step 1 Dim comp As Object = docl(i) If comp.NickName = "loopStart" Then Dim compp As IGH_Param = comp.Params.input(2) compp.VolatileData.Clear() compp.AddVolatileDataTree(anyData) Exit For End If Next End Sub
End Class
…
looked at autodesk simulation cfd 2015 and was optimistic because it had an export plugin from revit, which i use anyway for material takeoffs and etc, but found that it did not take solar radiation into account. This was a downer because I have heard that solar radiation could effect indoor airflow - convection - as much as 50 percent at a time.
Then I searched again and found that Hyperworks, a software by altair technology can be coupled with a radiation software. So I went through the trouble of obtaining an educational license of Hyperworks. However, though some email exchange I have found that the coupling is a one-way. The radiation analysis software was used, I think, for understanding the solar loading for a SOM project called church of light.
The support guy said : "Unfortunately our coupling with Hyperworks is really a one way coupling. We can accept H coefficients from their software in RadTherm, but they will not read in our wall temps. That said, it still can be a useful coupling in the sense that you can run the analysis in Hyperworks, send H coefficients to RadTherm, and run the analysis to better understand radiation and conduction. Most importantly, that analysis can be done for longer transient analysis, but will require much less compute time and resources."
Not only did I not understand what he means by the H coefficients, my wanting to get a CFD understanding coupled with solar radiation was again, unsatisfied. In the mean while I had to finish a presentation so I haven't had the time to try to get some result on the natural ventilation. I would probably need to look into how their solutions work before I can understand if their software would "do the job"
Thank you for letting me know about your work on this. I downloaded the Honeybee_Set EP Natural Ventilation component and made sure that it is allowed, but it does not show up in grasshopper.
You pointed out that "The component (and the corresponding equation) is mostly meant for cases where you have zones with windows that are NOT connected by an air wall (or a larger airflow network)." I wondered if you are suggesting it would be a code violation for zones to be connected by an air wall for fire safety reasons. It would be a violation I guess, like not putting an fiber insulation or some kind of smoke stop between Spandrel panels and the edge of a floor plate would be a code violation for a typical office building.
There is a project by kevin daly architects where you can see a section drawing with what seems like a cfd analysis (could be an illustration)
it was my initial visualization/simulation goals were for a facade design I am working on
1) an average air velocity across a zone at noon, for example, if a passive design strategy like this was used. for this I am guessing cfd is not entirely necessary. probably means that it could be used earlier in a design process, too. This would be more about user comfort.
2) at a later phase, like in detailing facade components, if airflow is indeed as expected for a zone that is connected to an air wall / chimney like feature (and to see if there is a proper mixing of air)
3) and a projection of energy savings, of course.
After seeing a video of simulation cfd I was optimistic, but like I said sim cfd does not take account of solar loading. I think I would probably go ahead start with one zone with sim cfd first, try three zones stacked on top of each other, then try hyperworks and try to factor in solar radiation.
For analyzing multiple zones on different levels, being able to add a chimney would be especially useful, I think. Having said that, I don't have a lot of experience of using honeybee except for the daylight component so it would take some time for me to understand the components.
I hope some of the information here is useful for you. after all, both sim cfd and hyperworks are commercial softwares and somewhat different than the e plus project you are working on, I guess but still trying to address a similar problem.
so.. in cased you missed it I was asking I downloaded the Honeybee_Set EP Natural Ventilation component and made sure that it is allowed and placed in the user object foler, but it does not show up in grasshopper. what could be the reason?
…