ur setup. Can you say what sensor you are using? Are you using an Arduino to write this ascii information to the serial port? If so, there may be some formatting code for the string that you'll need to do to get the Read component to function properly. I see that you were able to open the port and Start reading... so my first thought is that the data is formatted correctly....
All of the read components look for a specific character (in this case two characters) to indicate when it has reached the end of the line being read and should spit out the data. In this case, Firefly uses the Carriage Return (\r) and Line Feed (\n) to know when it has reached the end of the line. In arduino, these are automatically added to any line if you use the Serial.println("blah, blah, blah"); command. Notice, this is different from the Serial.print("nothing to see here"); command. This doesn't mean that you can't still use the regular print command... it's just you need to use the println command to indicate when you've reached the end of the line. Let's take a look at a simple example.
void setup() { Serial.begin(9600);}void loop() { int sensorValue = analogRead(A0); Serial.print("The value of the sensor is: "); Serial.println(sensorValue);
delay(20); // important to wait some small time so you aren't sending just a ton of info over to GH which will cause it to crash :(
}
The first print statement prints a string to the serial port... and the next one adds the current sensor value... and THEN adds the carriage return and line feed to start a new line. The nice thing about using these together is that you can concatenate any type of data you want. If you were to upload this sketch, you should see a sentence being printed to the serial port that says "The value of the sensor is: 512". I made up the number, but you get the idea. Notice, I also had to include a delay function. You don't always need this (there are other ways to go about this) but the important thing to note is that the loop cycle on the Arduino can run really fast. I mean... really fast. So, you wont want to send so much data over to GH, because this could flood the string buffer in the Read component and cause it to crash (eventually). It's a good idea to add some small time interval just to slow it down a bit. I should say that I've optimized the refresh rate in the next release so it's significantly faster... so hopefully this wont be as big of a problem... but hopefully that helps some.
Now... Why are you writing data to a sensor? Sensors by default are considered inputs... so I'm quite confused as to why you would want to send data back (if you are... then you need some way to handle the string data being sent from GH... this is the whole reason we built the Firefly firmata... it sets up the two-way protocol so you don't have to deal with all of that mess... If you're going to read and write, you're better off just uploading the firmata and using the Uno Read and Write components). Also, I'm not very familiar with the Hyperterm or Advanced Serial Port Terminal... but I will say that could get COM conflicts if you're trying to open the port with different tools. Anyway, I hope some of this helps you get up and running.
Cheers,
Andy
…
aph relaxation in 3D and more). There is much more already in our GitHub repos and more to be added. For getting an idea of our future direction check this lecture out. For getting a better understanding of graphs and graph theory watch this lecture and this lecture on a gamified spatial configuration process. Stay tuned for more and do not hesitate to post Python questions in the meantime.
ps. If you are having installation problems, please check the remedy suggested below:
Comment by Iman Sheikhansari on August 26, 2019 at 8:33amDelete Comment
HiIf you are encountering a problem with rhino 6 versions don't worryFollow these steps.1. Download SYNTACTIC from https://sites.google.com/site/pirouznourian/syntactic-design2. Install it and go to the installation folder, Drag & drop SYNTACTIC(green one) over your grasshopper canvas.3. Close your rhino and reopen it. 4. Type GrasshopperDeveloperSettings5. Tick the Memory load *.GHA assemblies using COFF byte arrays option6. Run grasshopper and enjoy plugin
…
cremental release is available for download. It fixes several bugs reported in the 0.9.0005 & 0.9.0006 versions. To wit:
Computer mice with smooth scrolling would not zoom well, this is fixed.
Previewable parameters with a lot of consecutive null items would crash, this is fixed.
Identical GHA files would collide during the loading process, this is handled.
GHA files with identical names would collide during the loading process, this is handled.
Solver Undo setting was not persistent, this is fixed.
Widget ZUI Zoom setting was not persistent, this is fixed.
Markov Widget Corner setting was not persistent, this is fixed.
Markov Widget Suggestion Count setting was not persistent, this is fixed.
Drag and Drop on Document and Template preview materials wasn't recorded, this is fixed.
AssignDataToParameter() COM-Access method was broken, this is fixed.
Geometry and Generic parameters with persistent data would not deserialize correctly, this is fixed.
Operator shortcuts via the Canvas popup instantiation menu no longer assigned data to the second parameter, this is fixed.
Cull Duplicates component did not always show the correct label upon deserialization, this is fixed.
Legacy VB/C# components would not correctly deserialize List access on input parameters, this is fixed.
Cloud Display component would still display old sprites on disconnect, this is fixed.
Minor changes to a document would trigger lengthy preview cache updates, slowing Grasshopper down. This is fixed.
Sphere 4Pt did not work correctly, this it fixed.
Failed data conversions in parameters would result in missing entries, this is fixed.
Text Tag components (2D & 3D) would not bake via the component menu, this is fixed.
There are also some new features:
Added Jump object for quickly navigating across a Canvas (Params.Util dropdown).
Added Relative Differences component which is basically the inverse of Mass Addition (Math.Operators dropdown).
Added tooltip wiggle controls to the Preferences window, Interface section.
'Draw Full Names' now also attempts to change the display of existing components, but only in the active document.
Drag+Dropping GHA, GHPY and GHUSER files onto the canvas now puts the original file into the bin.
Replaced Set Union component with a new one that has variable input parameters.
Replaced Set Intersection component with a new one that has variable input parameters.
Replaced And and Ternary And components with a single new one that has variable input parameters.
Replaced Or and Ternary Or components with a single new one that has variable input parameters.
Replaced Concatenate component with a new one that has variable input parameters.
Concatenate component now has a segment join option available via the component menu.
Added Digit options to the Transform Matrix Display object.
Integer parameters which represent options now have more informative context menus.
--
David Rutten
david@mcneel.com
Poprad, Slovakia
…
Added by David Rutten at 11:06am on September 14, 2012
hat since we create a list of materials and we assign them to surfaces - volumes the next step could be to have an Life Cycle Analysis and Financial assessment produced.
The most common form to produce an LCA into a form that is commonly used and easily communicated is in the form of Environmental Product Declarations (EPDs) that follow ISO 14025:2006. As every form of LCA, EPDs raise a bunch of question regarding their boundaries and the accuracy of the results especially if we include the factor of location. In comparison with other LCA practices though, EPDs have to be followed by Product Category Rules (defining the boundaries of the study) that can be reviewed by external parties if the EPD is to go public. Part from that EPD results reflect each stage of the life cycle of a product including potential benefits from Reuse or Recycling. Finally if you have a system - for example a building - you can add the EPDs of the different subcomponents forming the building and get a final EPD for the building itself - the point where I think HB's functionality is fully aligned.
The financial assessment can easily be concluded if one has the price of the material he/she uses. Finally the environmental indicators of the EPDs (LCI, LCIA) can be translated into Shadow Costs (Shadow costs for Environmental Indicators here) and added to the final financial assessment as an option.
I have developed a similar plug-in (in C#) for Grasshopper for my master's thesis last year. The project focused on the comparison between constructing normally and constructing implementing Design for Deconstruction practices in steel buildings. The idea was to compare the two cases based on their environmental and financial performance. In the process I included also options for transportation of the material and for shadow cost, embodied energy and carbon assessment and more. The final outcome can be visualised in Rhino's viewports and exported to excel sheets. The plug-in is connected to local db with EPD data for steel profiles. The same scheme though can be followed for any type of material if we have the right database to connect it to!
Please have a look if interested at the report here! And let me know if you have any questions!
Please note that the report includes 3+ chapters dedicated to design for deconstruction practices e.t.c that are irrelevant with the topic but maybe interesting to read:)
Also if someone is interested in the report I can always send it to you.
(I will upload a video -runthrough of the plug-in later this week)
I would be very interested to have these capabilities in LB and HB and happy to help realising it!
Thanks
Tasos
…
o, presso la sede Eurac e il TIS, nei giorni 21,22 e 23 maggio 2015.
Il processo di progettazione integrata è riconosciuto come metodo per ottenere gli elevati livelli di qualità oggi richiesti agli edifici. Con questo approccio diventano sempre più rilevanti il comfort visivo e la gestione dell’illuminazione naturale in relazione al risparmio energetico. Di fatto, il nuovo protocollo Leed v4 riconosce crediti ad hoc e conferma l’importanza della progettazione daylighting per “collegare gli occupanti con lo spazio esterno, rinforzare i ritmi circadiani, ridurre l’uso dell’illuminazione elettrica con l’introduzione della luce naturale negli spazi”.
Una progettazione robusta richiede l’uso di strumenti di simulazione efficaci e Radiance è riconosciuto come uno dei software con le capacità di fornire risultati affidabili. Radiance è utilizzato sia a livello di ricerca che tra i progettisti, ed è tra i più accurati per la simulazione professionale della luce naturale ed artificiale. Non ha limiti di complessità geometrica ed è adatto a essere integrato in altri software di calcolo e interfacce grafiche. Le principali e più versatili tra queste (DIVA4Rhino, plug-ins per Grasshopper e Rhinoceros3D), essendo in grado di facilitare notevolmente le procedure di programmazione, saranno oggetto del corso.
Il corso è rivolto a progettisti e ricercatori che vogliano acquisire strumenti pratici per la simulazione con Radiance al fine di mettere a punto e verificare le soluzioni più adatte alle proprie esigenze. Sono previste lezioni di teoria e pratica con esempi ed esercitazioni volte a coprire in modo dimostrativo ed interattivo i concetti trattati.
Il corso viene riconosciuto con 15 crediti dall’Ordine degli Architetti.
Le domande di iscrizione devono essere presentate entro il 27 aprile 2015.
Scarica la brochure con tutte le informazioni Corso Radiance - EURAC.pdf
Il corso è sponsorizzato da Pellinindustrie.…
hop innovativo sulle prospettive e sfide future del design computazionale.
INFO ED ISCRIZIONI
PLUG IT | Rhino + Grasshopper | Livello Base | Modellazione parametrica e controllo di forme complesse
Plug it, primo step del percorso formativo in tre fasi “AAD Workshop Series“. Plug it fornirà ai partecipanti un’effettiva padronanza delle più avanzate tecniche di modellazione digitale, approfondendo le metodologie della modellazione algoritmica e parametrica nel campo dell’architettura e del design del prodotto. Il corso è rivolto a studenti e professionisti dei settori della progettazione architettonica, design, moda e gioielleria, con esperienza minima nel disegno CAD bidimensionale (acquisita su qualsiasi piattaforma software) e si articolerà in lezioni teoriche frontali ed esercitazioni guidate
FORM FINDING STRATEGIES | Livello Intermedio | Analisi ambientale ed ottimizzazione della forma
Form Finding Strategies è il secondo step del percorso formativo in tre fasi “AAD Workshop Series“. Il workshop intende esplorare le possibilità di generazione di forme efficienti in relazione ad influenze esterne ed alle caratteristiche intrinseche della materia stessa. Analisi ambientale (input solari, termici ed acustici) ed analisi/ottimizzazione strutturale FEM saranno le principali metodologie utilizzate per raggiungere gli obiettivi di ricerca della forma. Saranno introdotti numerosi plug-ins tra cui: Weaverbird, Kangaroo, Geco/Ecotect, Ladybug, Millipede. Il corso si rivolge a studenti e professionisti con conoscenza base di Rhino e Grasshopper.
PERSPECTIVES | Livello Avanzato | Python coding e modellazione algoritmica avanzata
Il nuovo corso Perspectives proposto per la prima volta nel 2019 (ed ultimo step del percorso formativo in tre fasi “AAD Workshop Series) introdurrà gli studenti alla programmazione Python ed alla sua integrazione con Grasshopper. Verranno inoltre esplorate tecniche avanzate di generazione formale basate su iterazioni. Tra i principali plugins utilizzati: GhPython, Anemone, Hoopsnake, Plankton, MeshMachine, Pufferfish. Pensato come workshop innovativo sulle prospettive e sfide future del design computazionale, è rivolto a studenti e professionisti con esperienza in modellazione algoritmica con Grasshopper.…
m
-Area of blue line: min. 80% of the rectangel a x b
-Max. hight h of the top point: h,max = a
-Min. Volume between rectangel a x b and membrane: 500 m3
Can anyone help me?…
ou will see all of the available components on a ribbon at once so there is no need to keep clicking drop down menus.
It's all about discoverability with GH. What if you're a beginner and don't know about the Create Facility (dbl click canvas) how can you find Extr?
Even if you hover over every component or use the drop down lists you will not see the name Extr appear anywhere.
Sure it makes sense that Extr is short for Extrude but it's also the Nick Name of Extrude to Point component
So you can easily miss the fact that one has a Distance Input verses a Point Input.
I think I made the move to Icons around about the move from version 0.5 to 0.6, possibly before. I initially thought that I would go back to text because I loved the mono chromatic look of the text but I soon realised that Icons were the way forward. The greatest benefit is speed. You don't need to digest and decipher every component (which is written 90 degrees to the norm).
I'm not saying you should move to Icons forthwith but at least consider that once you have a better knowledge and understanding of GH, Icons will set you free.
My top ten tips that I would highly recommend to anyone wanting to better themselves with GH.
1) Turn on Draw Icons
2) Turn on Draw Fancy Wires
3) Turn on Obscure Components
4) Use the Create Facility like a Command Line eg "Slider=-1<0.75<2" or "Shiftlist=-1"
5) Use Component Aliases to customise your use of the Create Facility eg giving the Point XYZ component an alias of XYZ will bring it up as the first option on the Create Facility as opposed to the other possibilities.
6) Try to answer other people's questions even if it's not relevant to your own area. By looking into solving a problem outside of your comfort zone and then posting your results it is very rewarding but it also lets you see the other approaches that get posted in a new light.
7) Take the time to understand Data/Path structures.
8) Buy a second monitor - There is nothing that can compare to real estate when working in Grasshopper.
9) Read Rajaa Issa's Essential Mathematics
10) Pick a panel in a tab on the ribbon and get to know every component inside and out and then move on. Start with the Sets Tab > List Panel…
ne diverse digital design methodologies and the use of different tools such as Autodesk Maya, Rhinoceros and Grasshopper.
Building up technical skills will provide the attendees with a solid platform from which to start rethinking and exploring innovative architectural ideas in collaboration with the team and the tutors.
URBAN FIELDS
Phase I
In the first part of the workshop attendees will be looking at field conditions and how to generate and design such fields that can help structure a possible urban condition in Florence.
We will be exploring dynamic systems, geometric systems and network theories to generate and design an abstract field condi- tion that extends the urban experience of the city onto the vertical dimensions of towers. Simple operations that would span variations from an initial state will give rise to high level of com- plexity.
The goal of this exercise is to create a rich and diversified intel- ligible urban space that can be later on subjected to local inter- ventions and zooming in to locally enhance each design.
AGENT - BODIES POLYMORPHISM
Phase II
The second part of the workshop will build upon first phase; par- ticipants will select one archetype (high rise tower) as a study model for further development.
Besides engaging with multi agent algorithms design strategies, attendees will address strategic utilisation of structurally and environmentally generated morphologies to design coherent and highly differentiated tower exo-skeletons.
Tutors will introduce agent-bodies polymorphism in order to explore the generation of structural aware and capable geom- etries through agent based formation of non-linear hierarchies and emergent patterns. These agent-bodies will operate in a complex spatial manner to form structure, partitions or enclo- sure and will operate across scales, creating a poly-scalar level of detail.
Attendees will speculate how autonomous systems can cre- ate new structures and intelligent distribution of structural elements, about new collaborative strategies of construction and the performativity they will evoke (performance, effects, responsiveness, interaction).
Fees
Early registration (before 1st June)
Students 390€ - Professionals 440€
Late registration (after 1st June)
Students 490€ - Professionals 540€
More info and Applications
https://www.ax-om.com/edu/polymorphism/
…
heranno la maggior parte delle funzionalità di Rhino, tra cui i comandi più avanzati per la creazione di superfici.
Struttura Le lezioni tratteranno in maniera sistematica argomenti riguardanti l'interfaccia utente, i comandi, la creazione e modifica di curve, superfici e solidi.
Risultati attesi Dopo questo corso l’allievo deve essere in grado di:
• Muoversi agevolmente attraverso l’interfaccia di Rhino.
• Identificare quando è richiesto modellare in maniera free-form o di precisione.
• Creare e modificare curve, superfici e solidi anche di natura complessa.
• Utilizzare ausili di modellazione per la precisione.
• Produzione di facili rendering per la visualizzazione dei modelli di Rhino.
Destinatari Questo corso è rivolto a progettisti e studenti che vogliono imparare in modo efficace i concetti e le caratteristiche del software di modellazione Rhinoceros. Le lezioni saranno esposte da un docente ART qualificato dalla McNeel esperto di modellazione Nurbs.
Prerequisiti Per affrontare il corso sono richieste competenze di Windows, passione e volontà di modellazione; precedenti esperienze di modellazione, anche con altri software, sono utili ma non indispensabili.
Attestato Alla fine del corso verrà rilasciata l’attestato di partecipazione ad un corso qualificato McNeel valido anche per l’ottenimento di crediti formativi universitari.
Luogo Le lezioni si terranno in Via dei Valeri 1 int.9, 00184 ROMA
Pre-iscrizione Per garantire il numero di iscrizioni è necessaria una pre-iscrizione inviando una mail all'indirizzo 4planstudio@gmail.com il cui contenuto deve essere il seguente:
Nome:
Cognome:
Indirizzo di residenza:
mail:
telefono:
La preiscrizione dovrà avvenire entro il 30/11. A seguito di questa procedura verrà inviata dal tutor una mail di conferma con le procedure di iscrizione.
Quota di iscrizione
Il corso prevede le seguenti quote di iscrizione:
studenti: 400 Euro; (sarà necessario presentare in copia la ricevuta di pagamento dell’anno in corso)
non studenti: 470 Euro. Le quote sono considerate iva inclusa.
Info
Per ulteriori informazioni sono a disposizione i seguenti contatti:
Responsabile didattico: arch. Michele Calvano
Info mail: 4planstudio@gmail.com
tel: 340 3476330
…