he TOF and TSRF indices. They show, how "distant" is your _PV_SWHsurface from the optimal _PV_SWHsurface surface in terms of tilt and azimuth angles.However, in your case we are not interested in TOF and TSRF indices. We would just like to know what are the _PV_SWHsurface optimal tilt and azimuth angles, regardless of the supplied _PV_SWHsurface.
So the circular surface supplied to the "TOF" component's _PV_SWHsurface input is irrelevant. It can be of any area, and any tilt/azimuth angle.The PV_SWHsurfacesArea output of the "PV SWH system size" component depends on a couple of factors:moduleActiveAreaPercent_ (leave it at 90%).
moduleEfficiency_,
systemSize_.Calculation of systemSize_ depends on your electricity demand, cost of the PV system, type of the object, country, local regulations etc. This is something that an engineer needs to determine.For example, in USA for a residential house in the Sunbelt, depending on finances, a household would try to cover 100% of its annual electricity needs with their PV system. Which means that the systemSize_ you chose needs to cover the annual electricity consumption. You can perform EnergyPlus simulation or use any other way to get the annual electricity consumption.
Ladybug "Photovoltaics Performance" component can calculate the optimal systemSize_ by given the annual electricity consumption.However the component is made to address fixed tilt and azimuth PV systems only.An approximate way to overcome this is to calculate the optimal systemSize_ for fixed tilt and azimuth PV system, and then multiply it with the "difference in %s" panel at the very right of the fixed_vs_tracker_PV2.gh file. Again, this is not what Ladybug "Photovoltaics Performance" component is made to do, but it will probably get you in a ball park.
Inputted 32 degrees for north_ direction is actually 328 degrees.This is due to Ladybug Photovoltaics being based on NREL model which uses clockwise angles convention. This convention is also most commonly used in solar radiation analysis.
Dubai weather data files are uploaded in here.
…
GH, same as using sweep2 command in Rhino.
The one on the right is what I got so far (the output smooth our the kink of the original rails). Basically I am just following the methods provided by sdk sample: http://wiki.mcneel.com/developer/sdksamples/sweep2 .
The following is the function I copy and use directly from the SDK sample. By using this function, I can generate the sweep surface at right. But I want to have is the one in the middle with the kink edges. Can anyone show me how and where to modify he settings? I guess some sweep arguments need to be changed? I have try couples, such m_simplify, m_bSimpleSweep, m_bSameHeight, m_rebuild_count... but still cannot find a right combination for this function to output the sweep surface I want. Any suggestions or helps are very appreciated. Thanks for your help and time on this.
'Sweep2 function'----------------
Sub Sweep2( ByVal Rail1 As IOnCurve, _
ByVal Rail2 As IOnCurve, _
ByVal sCurves As List(Of IOnCurve), _
ByRef Sweep2_Breps As List(Of OnBrep))
'Define a new class that contains sweep2 arguments
Dim args As New MArgsRhinoSweep2
'Set the 2 rails
Dim Edge1 As New MRhinoPolyEdge
Dim Edge2 As New MRhinoPolyEdge
Edge1.Append(Rail1.DuplicateCurve())
Edge2.Append(Rail2.DuplicateCurve())
'Add rails to sweep arguments
args.m_rail_curves(0) = Edge1
args.m_rail_curves(1) = Edge2
args.m_bClosed = False
Dim section_curves As New List(Of OnCurve)
'Loop through sections to set parameters
For Each Section As IOnCurve In sCurves
Dim sCurve As OnCurve = Section.DuplicateCurve()
section_curves.Add(sCurve)
Dim t0 As Double = 0
If Not Edge1.GetClosestPoint(sCurve.PointAtStart(), t0) Then
If Not Edge1.GetClosestPoint(sCurve.PointAtEnd(), t0) Then
Dim s As Double = 0
sCurve.GetNormalizedArcLengthPoint(0.5, s)
Edge1.GetClosestPoint(sCurve.PointAt(s), t0)
End If
End If
args.m_rail_params(0).Append(t0)
Dim t1 As Double = 0
If Not Edge2.GetClosestPoint(sCurve.PointAtStart(), t1) Then
If Not Edge2.GetClosestPoint(sCurve.PointAtEnd(), t1) Then
Dim s As Double = 0
sCurve.GetNormalizedArcLengthPoint(0.5, s)
Edge2.GetClosestPoint(sCurve.PointAt(s), t1)
End If
End If
args.m_rail_params(1).Append(t1)
Next
'Set shapes
args.m_shape_curves = section_curves.ToArray
'Set the rest of parameters
args.m_simplify = 0
args.m_bSimpleSweep = False
args.m_bSameHeight = False
args.m_rebuild_count = -1 'Sample point count for rebuilding shapes
args.m_refit_tolerance = RMA.Rhino.RhUtil.RhinoApp.ActiveDoc.AbsoluteTolerance()
args.m_sweep_tolerance = RMA.Rhino.RhUtil.RhinoApp.ActiveDoc.AbsoluteTolerance()
args.m_angle_tolerance = RMA.Rhino.RhUtil.RhinoApp.ActiveDoc.AngleToleranceRadians()
Dim sBreps() As OnBrep = Nothing
If (RhUtil.RhinoSweep2(args, sBreps)) Then
For Each b As OnBrep In sBreps
Sweep2_Breps.Add(b)
Next
End If
Return
End Sub
…
ect + Geco
TUTORS:
Arturo Tedeschi (Authorized Rhino Trainer) + Maurizio Arturo Degni
Il workshop avanzato ECOLOGIC PATTERNS affronta l’impiego di strategie parametriche all’interno del processo progettuale, approfondendo l’utilizzo di Grasshopper in sinergia con plug-in, software di analisi ambientale e simulazione fisica. Obiettivo fondamentale è la generazione della forma come risultato di tecniche di form-finding e di input ambientali (solari, termici e acustici). Verranno acquisiti nuovi strumenti operativi e di simulazione al fine di costruire modelli parametrici ottimizzati in grado di adattarsi a diverse condizioni di contesto.
MORE INFO…
ive collaborative environment.
TYPE : Course module and Workshop
The event is open for anybody interested from all the fields of design, including: architecture, interior design, furniture design, product design, fashion design, scenography, and engineering.
1. COURSE MODULE (20-23 April 2014) - optional
+ type: 3 days intensive course regarding basic knowledge in parametric design (LEVEL 1)
+ software: Rhinoceros & Grasshopper
+ plugins: Kangaroo, Weaver Bird, Lunch box, Ghowl, Geco
+ achievements:
- acquainting to the components & the concept of Generative Design
- understanding the strategies in Algorithmic Design
- how to easily insert simple mathematical equation into the project to gain more control
- how to utilize proper plugins with respect to their nature of the project
- interacting with different analysis platforms such as Ecotect & remote controller
- solving several exercises with different scales( 2D- 3D ) during each phase of the workshop
2. WORKSHOP (23-27 April 2014)
A 5 day Design-Based Research Workshop exploring new techniques in Digital Architecture/Fabrication, with a specific focus on the use of generative systems and parametric modeling as tools for creative expression.
Our ultimate goal is to increasing the efficiency of utilizing digital tools in parallel with geometric performance of the primitive design agent.
+ + CONCEPT
Fashion and Architecture are both based on basic life necessities – clothing and shelter.
However, they are also forms of self-expression – for both creators and consumers.
Both fashion and architecture affect our emotional being in many ways.
The agenda of this workshop is to investigate on the overlap between these two areas of design, art & fashion.
Fashion and architecture express ideas of personal, social and cultural identity, reflecting the concerns of the user and the ambition of the age. Their relationship is a symbiotic one and throughout history, clothing and buildings have echoed each other in form and appearance. This only seems natural as they not only share the primary function of providing shelter and protection for the body, but also because they both create space and volume out of flat, two-dimensional materials.
While they have much in common, they are also intrinsically different – address the human scale, but the proportions, sizes and shapes differ enormously.
+ + + OBJECTIVES
So far, Architects have been using techniques such as folding, bending etc. to create space, structural roofs or different other structural shapes.
The agenda of this workshop goes further with the investigation of algorithmic thinking through generative tools Integrated in design.
The challenge is creating a bridge that connects these two areas of design, architecture and fashion that perform at two opposite scales.
+ + + + TECHNICAL BRIEF
In the early stages physical models and low-tech strategies will be used, allowing the participants to gain a greater understanding of materials, fabrication and assembly methods as well as simple, yet pragmatic structural solutions.
Later in the workshop these strategies will be digitalized and elaborated using software visualizing tools such as Rhinoceros and the algorithmic plug-in Grasshopper.…
rves/holes. However, the Kangaroo script itself is prone to locking up so it seems like it might take forever. You can even double click stop the timer from the Windows task bar, I hadn't noticed that before:
You have to use that or right click disable the timer since even with the Reset toggle button input set to True the timer itself locks up the script a bit when you are changing things around.
Just setting the min/max numbers both to a desired mesh size gives a uniform mesh:
Oh weird, it's about if the timer is right click set to so small an interval that it gets ahead of Kangaroo! When you see how long each cycle is taking with the Display > Canvas Widgets > Profiler you just set the timer for above that and the interface comes back into being responsive. It only takes a few Kangaroo cycles to do the inflation, so a full second timer interval is even workable.
A finer mesh:
It's funny running it so slow since it overinflates at first, bulging out, before it equilibrates.
You have control over inflation pressure and mesh stiffness, for a variety of effects.
This is a good system once I realized the timer needed to be mellowed out.
What made it work was the fast custom meshing since a normal mesh is awful and MeshMachine wouldn't work with sharp corner holes at all, breaking out of the boundary even if I fixed curves or vertices or did the equivalent with NURBS surfaces instead of a starting mesh.
There is an initiation time for Kangaroo that doesn't show up on its Profiler time that happens even with the timer off.
There are some fine areas that can't inflate with a reasonable mesh setting:
Worth playing with but no match for ArtCAM since it suffers odd delays in between working fast. If I could get better 2D meshes, that were more adaptive it would be better, but MeshMachine is one of the only re-meshers I know and it's broken for even mildly sharp hole features.
Ah, how about a crude mesh that is then subdivided, guaranteeing inner vertices everywhere? Sort of works, but is still too dense. Way too dense to even do anything. The subdivision triangulates the quads, vastly increasing the mesh wire density. Better just to make a finer initial mesh with plenty of quads.…
Added by Nik Willmore at 12:57am on February 21, 2016
(1) I have been exporting small sections of a larger model into Maya from Rhino as FBX. In Maya I rotate and scale the models (-90 in X, Scale XYZ 0.001). The Named Views are being saved, but do not have a successful import into the Maya model. They do not appear as in Rhino, and the problem is not solved by scaling or rotating the cameras.
(2) If I try going the other direction, the cameras exported from Maya as FBX are also not aligning with the model in Rhino as they are in Maya.. I will do my best to post some images of the problem and hope you can help.
error !!
This is what the named views look like
here I am trying to the other way with a good view from Maya
strange placement..
This is the best result I can achieve, after I scale the camera by 1000
Any Advice???
Thanks, Robert.
…
TB of RAM. I think I'm going to start a GoFundMe campaign to buy one for myself :)
2- The server's cost is about $13 an hour. I get free access to supercomputer through my university and xsede.org because I earned an NSF Honorable mention last March, however, the supercomputers available through both resources are a little complicated for me to use, as opposed to the one available from amazon that has Microsoft server 2012 already installed.
3- I wanted to run 400 annual glare simulations for 400 different views.
4- I tried a to perform annual glare simulation for one view on my Dell XPS that has Intel Core i7-6700HQ processor and 16GB of system memory. The simulation took 2 hours to complete. Radiance parameter ab was set to 6.
5- I wanted to obtain the batch file for each view so I can run them on the server. So I used the fly component to run all 400 simulations and closed the cmd windows, that wasn't bad ( for me at least) because I asked my son to this job for me, he was just glad to help me :)
6- I created one batch file using this cmd command:
dir /s /b *.bat > runall.bat
This created a file with the path to each .bat file. I edited this file in Notepad++ to include the word "start" at the beginning of each line. This was done using the "find and replace" dialogue box.
7- I split my newly created batch file into 3 batch files, each one has about 130 file names and " start" before the file names.
8- installed radiance on my server
9- Ran the first batch file on the server, this started 130 cmd windows performing my simulations, CPU usage was anywhere between 90% to 100% and about 105 GB of RAMs were used.
10. It took about 5 hours to complete all 130 simulations, I expected to run all in 2 hours but can't complain because this would've taken about 260 hours to run on my laptop. After the simulations done I ran the second and then the third batch files ( total of about 15 hours).
11. I got 400 valid dgb files. Couldn't be happier!
…
he time to work with it.
the project is about facade strips which turns along height. the top angle is
parallel to the facade and the bottom is max. 90 degrees twisted, but the strips
should turn diffrently to achieve more dinamic look.
first i have tried to achieve this by calculating distance between the rotation angle from points of the grid and a single point.
then i have tried to ad some more effecting points and used the distance to the divided surface (the circles are just to control the area of effection):
i manually lofted it.
the result is a bit annoying becouse the points that effect the angle are always visible:
i have triend to solve this by drawing a line and divided it to recieve points along the bottom of the geometry. the result is not working properly:
Anyway,
there must be a better/smoother way to achieve this. i would like to effect the twist of the surfaces by distance to a spline, but im just lost. can you help me please?
the problems im encountering:
0- distance spline to grid to effect the angle
1- list of x/y coordinates and angle of rotation for each point of the grid
2- export points to excel
3- lofting lines in one direction only (x1, x2, x3...)
4- reduce the list data to 2 decimal (0,00)
5- maybe angle from radian to degrees
thx…
ort and export from the images below and also from the HELP file of DB in attachments (Page 71: Importing Geometric Data; Page 78-80: Import 3 - D CAD Data). In their HELP file, they mention about "import geometric data".
However, regarding the input of schedules, loads, constructions and etc., DB normally uses "Component " and "Template" (Page 29: Templates And Components; Page 591: Templates; Page 533: Components). "Templates" are databases of typical generic data, including Activity templates, Construction templates, Glazing templates, Facade templates, HVAC templates, Location Templates, and etc. "Component " are databases of individual data items (e.g. a construction type, material, window pane).
Both "Component " and "Template" are allowed to be imported and exported by using "Import / Export library data" command (.ddf format - DB Database File; Page 734: Import Components/Templates, Export Components/Templates). DB also allows us to build up our own libraries of templates and components (Page 731: Library Management; Page 733: Template Library Management).
In order to import both geometric information and other information related to schedules, loads, constructions and etc. from GH to BD, we supposed the following two ways:
1. GH(HB+GB) --> gbXML (both geometric and "Component " and "Template" information) --> DB
This is the way we most prefer. We did see information related to schedules, loads, constructions encoded in the gbXML file generated by GB, but still do not know the reason why DB did not take this information (I also mentioned this in Q6 within the gh file). We assume this might because the gbXML file we create encodes the schedules based on a different template / schema than the one DB expects. We also post this question to the DB forum for help.
(http://www.designbuilder.co.uk/component/option,com_forum/Itemid,25/page,viewtopic/p,13755/#13755)
2. GH(HB+GB) --> gbXML (geometric information only) + .ddf ("Component " and "Template" information only) --> DB
If the first way doesn't work and DB only takes geometric information from the gbXML, then we might think of the other way - generating the .ddf files from GH(HB+GB) to pass the schedule, load and construction information to DB.
I was wondering if it is feasible for HB and GB to have this function? And what is your suggestion to achieve this?
In addition, we notice that DB can export XML files (not gbXML), so we are trying to figure out if DB also accepts / reads the XML file. If so, we might be able to convert the gbXML (with both geometric and schedule information) to XML. What do you think about that?
Thank you again for all your help!
Best,
Ding
DB import
DB export
Template libraries
Component libraries
…
Introduction to Grasshopper Videos by David Rutten.
Wondering how to get started with Grasshopper? Look no further. Spend an some time with the creator of Grasshopper, David Rutten, to learn the