ing illuminance and limiting exposure (lux hours). Hours with direct solar irradiance are likely to exceed the limiting illuminance thresholds, which range from (200 to 50 lux as per Table 3.4 in CIE 157:2004). It makes sense to consider direct illuminance (an ab=0 simulation in Honeybee) separately from a normal illuminance calculation.
Assuming that the museum exhibits have low to high responsivity to light, an ideal solution would minimize direct sunlight. For daylight from the sky and reflected light, it might be enough to keep the illuminance levels below the recommended thresholds and then sum up lux-hours.
Daysim, the annual daylighting engine used by Honeybee and DIVA, is not very accurate for direct-sun calculations. You will get more accurate results if you run your analysis with Radiance directly.
Instead of considering the horizontal illuminance grids, one can create grids that correspond to the dimensions of the exhibit and then average those values. I think single points, as shown in your gh file might not suffice. Calculating lux-hours is by far the simplest part of such a simulation. It will only require averaging these points, extracting them into an array and then summing up that array.…
eñadores, y creativos interesados en el aprendizaje de metodos avanzados de generación y racionalización de geometría compleja, y su implementación en distintas etapas del proceso de diseño.
Se abordaran los conceptos básicos para hacer frente a diversas problemas de diseño a través de la implementación de una serie de plataformas computacionales con el objetivo de construir un flujo de trabajo que permita optimizar proyectos de diversa escala y explorar esquemas geometricos complejos de manera rápida y eficiente.A lo largo del 6 dias trabajaremos con la plataforma de Modelado 3d Rhinoceros, el entorno de programación visual de Grasshopper y el motor de Renderizado de Vray.Estudiantes: $4,500.00Profesionistas: $5,500.00info+inscripciones:workshop@complexgeometry.com[044] 33 3956 9209[044] 33 1410 8975[044] 81 1916 8657
…
nowledge, tools, materials and machines. The Clusters provide a focus for workshop participants working together within a common framework.
Clusters provide a forum for the exchange of ideas, processes and techniques and act as a catalyst for design resolution. The Workshop is made up of ten Clusters that respond in diverse ways to the sg2012 Challenge Material Intensities. The Call for Clusters is now open to proposals which respond in innovative ways to this year's challenge.
Deadline: September 19 2011
More information can be found here:
http://smartgeometry.org/index.php?option=com_content&view=article&id=129&Itemid=146
sg2012 takes place from 19-24 March 2012 at EMPAC (http://empac.rpi.edu/) and is hosted by Rensselaer Polytechnic Institute in Troy, upstate New York USA. The Workshop and Conference will be a gathering of the global community of innovators and pioneers in the fields of architecture, design and engineering.
The event will be in two parts: a four day Workshop 19-22 March, and a public conference beginning with Talkshop 23 March, followed by a Symposium 24 March. The event follows the format of the highly successful preceding events sg2010 Barcelona and sg2011 Copenhagen.
sg2012 Challenge Material Intensities
Simulation, Energy, Environment
Imagine the design space of architecture was no longer at the scale of rooms, walls and atria, but that of cells, grains and vapour droplets. Rather than the flow of people, services, or construction schedules, the focus becomes the flow of light, vapour, molecular vibrations and growth schedules: design from the inside out.
The sg2012 challenge, Material Intensities, is intended to dissolve our notion of the built environment as inert constructions enclosing physically sealed spaces. Spaces and boundaries are abundant with vibration, fluctuating intensities, shifting gradients and flows. The materials that define them are in a continual state of becoming: a dance of energy and information.Material potential is defined by multiple properties: acoustical, chemical, electrical, environmental, magnetic, manufacturing, mechanical, optical, radiological, sensorial, and thermal. The challenge for sg2012 Material Intensities is to consider material economy when creating environments, micro-climates and contexts congenial for social interaction, activities and organisation. This challenge calls for design innovation and dialogue between disciplines and responsibilities.sg2010 Working Prototypes strove to emancipate digital design from the hard drive by moving from the virtual to the actual in wrestling with the tangible world of physical fabrication. sg2011 Building the Invisible focused on informing digital design with real world data. sg2012 Material Intensities strives to energise our digital prototypes and infuse them with material behaviour. They have the potential to become rich simulations informed by the material dynamics, chemical composition, energy flows, force fields and environmental conditions that feed back into the design process.
More information can be found at http://www.smartgeometry.org…
[2 of 8] No context surfaces...5. [3 of 8] Writing geometry...6. [4 of 8] Writing Electric Load Center - Generator specifications ...7. [5 of 8] Writing materials and constructions...8. [6 of 8] Writing schedules...9. [7 of 8] Writing loads and ideal air system...10. [8 of 8] Writing outputs...11. ...... idf file is successfully written to : C:\Users\Personal\Desktop\TESI\x006\THOR001\EnergyPlus\THOR001.idf12. 13. Analysis is running!...14. C:\Users\Personal\Desktop\TESI\x006\THOR001\EnergyPlus\eplusout.csv15. ......
Done! Read below for errors and warnings:
16. 17. Program Version,EnergyPlus, Version 8.3.0-6d97d074ea, YMD=2016.01.17 17:56,IDD_Version 8.3.018. 19. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.20. 21. ************* Beginning Zone Sizing Calculations22. 23. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)24. 25. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00126. 27. ** ~~~ ** because vertex 1 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00128. 29. ** ~~~ ** (Dot Product indicator=184.4593)30. 31. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.32. 33. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)34. 35. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00136. 37. ** ~~~ ** because vertex 2 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00138. 39. ** ~~~ ** (Dot Product indicator=184.4593)40. 41. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.42. 43. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)44. 45. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00146. 47. ** ~~~ ** because vertex 3 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00148. 49. ** ~~~ ** (Dot Product indicator=184.4593)50. 51. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.52. 53. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)54. 55. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00156. 57. ** ~~~ ** because vertex 4 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00158. 59. ** ~~~ ** (Dot Product indicator=184.4593)60. 61. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.62. 63. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)64. 65. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00166. 67. ** ~~~ ** because vertex 1 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00168. 69. ** ~~~ ** (Dot Product indicator=184.4593)70. 71. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.72. 73. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)74. 75. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00176. 77. ** ~~~ ** because vertex 2 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00178. 79. ** ~~~ ** (Dot Product indicator=184.4593)80. 81. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.82. 83. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)84. 85. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00186. 87. ** ~~~ ** because vertex 3 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00188. 89. ** ~~~ ** (Dot Product indicator=184.4593)90. 91. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.92. 93. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)94. 95. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00196. 97. ** ~~~ ** because vertex 4 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00198. 99. ** ~~~ ** (Dot Product indicator=184.4593)100. 101. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.102. 103. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)104. 105. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001106. 107. ** ~~~ ** because vertex 1 of back surface=PELLE_COMUNIONE002 is in front of receiving surface=PELLE_COMUNIONE001108. 109. ** ~~~ ** (Dot Product indicator=184.4593)110. 111. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.112. 113. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)114. 115. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001116. 117. ** ~~~ ** because vertex 2 of back surface=PELLE_COMUNIONE002 is in front of receiving surface=PELLE_COMUNIONE001118. 119. ** ~~~ ** (Dot Product indicator=184.4593)120. 121. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.122. 123. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)124. 125. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001126. 127. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001128. 129. ** ~~~ ** (Dot Product indicator=182.6148)130. 131. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.132. 133. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)134. 135. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001136. 137. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001138. 139. ** ~~~ ** (Dot Product indicator=92.2297)140. 141. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.142. 143. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)144. 145. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001146. 147. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001148. 149. ** ~~~ ** (Dot Product indicator=92.2297)150. 151. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.152. 153. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)154. 155. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001156. 157. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001158. 159. ** ~~~ ** (Dot Product indicator=182.6148)160. 161. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.162. 163. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)164. 165. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001166. 167. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001168. 169. ** ~~~ ** (Dot Product indicator=92.2297)170. 171. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.172. 173. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)174. 175. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001176. 177. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001178. 179. ** ~~~ ** (Dot Product indicator=182.6148)180. 181. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.182. 183. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)184. 185. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001186. 187. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001188. 189. ** ~~~ ** (Dot Product indicator=92.2297)190. 191. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.192. 193. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)194. 195. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001196. 197. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001198. 199. ** ~~~ ** (Dot Product indicator=1.8446)200. 201. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.202. 203. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)204. 205. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001206. 207. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001208. 209. ** ~~~ ** (Dot Product indicator=1.8446)210. 211. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.212. 213. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)214. 215. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001216. 217. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_3 is in front of receiving surface=PELLE_COMUNIONE001218. 219. ** ~~~ ** (Dot Product indicator=92.2297)220. 221. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.222. 223. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)224. 225. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001226. 227. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_3 is in front of receiving surface=PELLE_COMUNIONE001228. 229. ** ~~~ ** (Dot Product indicator=1.8446)230. 231. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.232. 233. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)234. 235. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001236. 237. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_3 is in front of receiving surface=PELLE_COMUNIONE001238. 239. ** ~~~ ** (Dot Product indicator=92.2297)240. 241. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.242. 243. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)244. 245. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001246. 247. ** ~~~ ** because vertex 3 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE001248. 249. ** ~~~ ** (Dot Product indicator=184.4593)250. 251. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.252. 253. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)254. 255. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001256. 257. ** ~~~ ** because vertex 4 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE001258. 259. ** ~~~ ** (Dot Product indicator=184.4593)260. 261. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.262. 263. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)264. 265. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001266. 267. ** ~~~ ** because vertex 1 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE001268. 269. ** ~~~ ** (Dot Product indicator=184.4593)270. 271. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.272. 273. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)274. 275. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001276. 277. ** ~~~ ** because vertex 2 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE001278. 279. ** ~~~ ** (Dot Product indicator=184.4593)280. 281. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.282. 283. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)284. 285. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001286. 287. ** ~~~ ** because vertex 1 of back surface=WIN_001_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001288. 289. ** ~~~ ** (Dot Product indicator=180.7210)290. 291. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.292. 293. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)294. 295. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001296. 297. ** ~~~ ** because vertex 3 of back surface=WIN_001_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001298. 299. ** ~~~ ** (Dot Product indicator=180.7210)300. 301. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.302. 303. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)304. 305. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001306. 307. ** ~~~ ** because vertex 2 of back surface=WIN_001_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001308. 309. ** ~~~ ** (Dot Product indicator=180.7210)310. 311. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.312. 313. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)314. 315. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001316. 317. ** ~~~ ** because vertex 3 of back surface=WIN_001_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001318. 319. ** ~~~ ** (Dot Product indicator=180.7210)320. 321. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.322. 323. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)324. 325. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001326. 327. ** ~~~ ** because vertex 3 of back surface=PELLE_OVEST is in front of receiving surface=PELLE_COMUNIONE001328. 329. ** ~~~ ** (Dot Product indicator=184.4593)330. 331. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.332. 333. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)334. 335. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001336. 337. ** ~~~ ** because vertex 4 of back surface=PELLE_OVEST is in front of receiving surface=PELLE_COMUNIONE001338. 339. ** ~~~ ** (Dot Product indicator=184.4593)340. 341. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.342. 343. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)344. 345. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001346. 347. ** ~~~ ** because vertex 1 of back surface=WIN_002_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001348. 349. ** ~~~ ** (Dot Product indicator=180.7210)350. 351. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.352. 353. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)354. 355. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001356. 357. ** ~~~ ** because vertex 3 of back surface=WIN_002_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001358. 359. ** ~~~ ** (Dot Product indicator=180.7210)360. 361. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.362. 363. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)364. 365. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001366. 367. ** ~~~ ** because vertex 2 of back surface=WIN_002_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001368. 369. ** ~~~ ** (Dot Product indicator=180.7210)370. 371. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.372. 373. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)374. 375. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001376. 377. ** ~~~ ** because vertex 1 of back surface=WIN_002_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001378. 379. ** ~~~ ** (Dot Product indicator=180.7210)380. 381. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.382. 383. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)384. 385. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001386. 387. ** ~~~ ** because vertex 3 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001388. 389. ** ~~~ ** (Dot Product indicator=184.4593)390. 391. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.392. 393. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)394. 395. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001396. 397. ** ~~~ ** because vertex 4 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001398. 399. ** ~~~ ** (Dot Product indicator=184.4593)400. 401. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.402. 403. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)404. 405. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001406. 407. ** ~~~ ** because vertex 7 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001408. 409. ** ~~~ ** (Dot Product indicator=184.4593)410. 411. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.412. 413. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)414. 415. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001416. 417. ** ~~~ ** because vertex 8 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001418. 419. ** ~~~ ** (Dot Product indicator=184.4593)420. 421. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.422. 423. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)424. 425. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001426. 427. ** ~~~ ** because vertex 1 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001428. 429. ** ~~~ ** (Dot Product indicator=184.4593)430. 431. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.432. 433. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)434. 435. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001436. 437. ** ~~~ ** because vertex 4 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001438. 439. ** ~~~ ** (Dot Product indicator=184.4593)440. 441. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.442. 443. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)444. 445. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001446. 447. ** ~~~ ** because vertex 5 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001448. 449. ** ~~~ ** (Dot Product indicator=184.4593)450. 451. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.452. 453. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)454. 455. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001456. 457. ** ~~~ ** because vertex 8 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001458. 459. ** ~~~ ** (Dot Product indicator=184.4593)460. 461. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.462. 463. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)464. 465. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001466. 467. ** ~~~ ** because vertex 1 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002468. 469. ** ~~~ ** (Dot Product indicator=167.5695)470. 471. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.472. 473. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)474. 475. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001476. 477. ** ~~~ ** because vertex 2 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002478. 479. ** ~~~ ** (Dot Product indicator=167.5695)480. 481. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.482. 483. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)484. 485. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001486. 487. ** ~~~ ** because vertex 3 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002488. 489. ** ~~~ ** (Dot Product indicator=195.1092)490. 491. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.492. 493. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)494. 495. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001496. 497. ** ~~~ ** because vertex 4 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002498. 499. ** ~~~ ** (Dot Product indicator=195.1092)500. 501. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.502. 503. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)504. 505. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001506. 507. ** ~~~ ** because vertex 3 of back surface=PELLE_COMUNIONE001 is in front of receiving surface=PELLE_COMUNIONE002508. 509. ** ~~~ ** (Dot Product indicator=167.5695)510. 511. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.512. 513. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)514. 515. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001516. 517. ** ~~~ ** because vertex 4 of back surface=PELLE_COMUNIONE001 is in front of receiving surface=PELLE_COMUNIONE002518. 519. ** ~~~ ** (Dot Product indicator=167.5695)520. 521. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.522. 523. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)524. 525. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001526. 527. ** ~~~ ** because vertex 1 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002528. 529. ** ~~~ ** (Dot Product indicator=32.0568)530. 531. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.532. 533. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)534. 535. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001536. 537. ** ~~~ ** because vertex 2 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002538. 539. ** ~~~ ** (Dot Product indicator=139.1556)540. 541. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.542. 543. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)544. 545. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001546. 547. ** ~~~ ** because vertex 3 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002548. 549. ** ~~~ ** (Dot Product indicator=139.1556)550. 551. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.552. 553. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)554. 555. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001556. 557. ** ~~~ ** because vertex 4 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002558. 559. ** ~~~ ** (Dot Product indicator=32.0568)560. 561. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.562. 563. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)564. 565. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001566. 567. ** ~~~ ** because vertex 1 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002568. 569. ** ~~~ ** (Dot Product indicator=167.5695)570. 571. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.572. 573. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)574. 575. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001576. 577. ** ~~~ ** because vertex 2 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002578. 579. ** ~~~ ** (Dot Product indicator=167.5695)580. 581. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.582. 583. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)584. 585. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001586. 587. ** ~~~ ** because vertex 3 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002588. 589. ** ~~~ ** (Dot Product indicator=167.5695)590. 591. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.592. 593. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)594. 595. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001596. 597. ** ~~~ ** because vertex 4 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002598. 599. ** ~~~ ** (Dot Product indicator=167.5695)600. 601. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.602. 603. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)604. 605. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001606. 607. ** ~~~ ** because vertex 1 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002608. 609. ** ~~~ ** (Dot Product indicator=195.1092)610. 611. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.612. 613. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)614. 615. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001616. 617. ** ~~~ ** because vertex 2 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002618. 619. ** ~~~ ** (Dot Product indicator=195.1092)620. 621. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.622. 623. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)624. 625. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001626. 627. ** ~~~ ** because vertex 3 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002628. 629. ** ~~~ ** (Dot Product indicator=195.1092)630. 631. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.632. 633. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)634. 635. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001636. 637. ** ~~~ ** because vertex 4 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002638. 639. ** ~~~ ** (Dot Product indicator=195.1092)640. 641. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.642. 643. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)644. 645. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001646. 647. ** ~~~ ** because vertex 5 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002648. 649. ** ~~~ ** (Dot Product indicator=195.1092)650. 651. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.652. 653. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)654. [...]
thisthe errorthat appen when i lunch E+ with only one zone....what is going on???? …
eventually found out about genetic algorithms on which I found extensive researches, projects,... ! I looked into it and ended up on a few papers which I believe are the jumpstart for my master thesis.
"Galapagos; on the logic and limitations of generic solvers" by David RuttenArticle in Architectural Design 83(2) March 2013
"Black-box optimisation methods for architectural design" by Thomas Wortmann and Giacomo NanniciniConference Paper: CAADRIA 2016, At Melbourne, AU, Volume: 177-186
So I started looking into alternatives to genetic algorithms in architectural design.So far, I've ended up on :
Thomas Wortmann's work with the surrogate(or model) based optimization approach!You can check out the tool he developped for GH (Opossum):http://www.food4rhino.com/app/opossum-optimization-solver-surrogate-models
Judyta Cichocka's work, specially with the Swarm approachYou can check out the tool she developped for GH (Silvereye):http://www.food4rhino.com/app/silvereye-pso-based-solver
And that's it !!! I've been researching through article references (mainly on "researchgate") but I'm now stuck in a loop of references I already visited!That probably means the litterature on the subject is not (yet) extended but I might probably be missing something.The keywords make it difficult to search : "optimisation", "algorithms", "architecture", send me most of the time to computational engineering and deep mathematics papers I unfortunately do not have the background knowledge to comprehend ! So there it is ! If you have any clue of where (or how ! ) I should be looking, please tell me :)I know Mr Rutten is pretty active on the forum so hopefully... (fingers crossed :p) !Also if you have any good tips for getting into algorithms in general (you think could help), I'd be glad to hear(read) it ! A book, tutorials maybe ?!So, autors, architects, projects books, articles, conferences I should go to,specialized architecture offices/studios (I'm also looking for an internship so ...).If you know about a more appropriate forum please let me know !If you want to get deeper into this, you can contact me at :
e1635331@student.tuwien.ac.at
tdissaux@student.ulg.ac.be
My master thesis is due for may 2018 but I have a paper to write for January 2018 in order to be elligible for a PHD program afterwards.What I mean by that is that if you read this message in 6 month, I'll still be open to discussion !
I am right now an erasmus student at TUWien (Vienna) but my main university is The university of Liège in Belgium.I can handle French, English, Italian litterature and eventually Dutch if really you think it's worth it ! I have access to most online libraries via my university's portals so access shouldn't be an issue !I'm very excited to hear from you I wish you all a great day,Cheers,Thomas
…
mers considering extreme sports reject mainstream retailers and like to check out small stores rather of at chains plus malls. Several smaller retailers discuss trends in sports shoe sales. http://skateszone.com/
Though athletic shoes and sports stores and from doorways retailers have reported somewhat uptick in footwear sales due to the increase in extreme sports, the particular beneficiaries inside the trend are independent surf and skate niche stores.
Some West Coast surf and skate shops stated teenagers and even more youthful Generation Xers are not only rejecting traditional sports, but they're also shunning mainstream retailers and malls meant for smaller niche shops transporting hard-to-come-by brands.
Eddie Miyoshi, district manager at Atomic Garage, a 3-store chain situated in Gardena, Calif., stated the soaring recognition of skateboard footwear has boosted the retailer's total footwear business 20-thirty percent this year, rather of '95.
Skate footwear presently represent 80-90 % of Atomic Garage's shoe sales, while couple of years back, Dr. Martens and Timberland drove the retailer's footwear business.
Like many retailers, Miyoshi pointed to Airwalk since the trend's catalyst.
However, if Airwalk broadened its distribution to larger chains, which are frequently located in malls, only a few skate shoe customers adopted. Rather, many youthful males have switched for your skate shops for additional elusive brands like Etnies, Duffs, and Electricity Footwear by Circus. By refusing to market bigger retailers or sports stores, these brands are increasing their cachet among youthful consumers.
"Kids don't want stuff which have been within the shops,In . Miyoshi added.
Searching ahead, Miyoshi forecasted skate shoe sales will remain strong through spring '97 provided "the [hot] vendors don't auction other [non-particularly shop] retailers."
"Skaters and non-skaters are rebelling against mainstream retailers so on to surf and skate shops for many looks," echoed Mark Richards, co-online sources Val Surf, a 3-store chain situated in North Hollywood, Calif. Soaring sales of skate footwear have driven total footwear receipts up 25 percent this year rather of '95.
"The quantity of that increase might be connected while using exposure of maximum games? I am unsure. [Skate footwear] may also be actually the think about the moment,In . Richards acknowledged. And in relation to getting this right look, youthful customers can be very picky.
"Skateboard footwear is a huge category for people, but we're not able to own the brands, Etnies, Duffs, Electricity and Nice, simply because they won't sell us," stated Mark Anderson, buyer at Chick's Sports, a six-store chain in Covina, Calif. "We have people coming every single day requesting them." Consequently, skate footwear have consistently ongoing to obtain about 5 % of Chick's overall footwear business. http://skateszone.com/the-top-8-best-skateboards-for-beginners-reviews-2017/
Nonetheless, some outdoors, niche sports and sports retailers are noting the growing recognition and coverage of maximum sports will receive a modest impact on footwear sales. Trailrunning footwear and approach/outdoors crosstrainers will be the two groups benefiting the very best inside the recognition. Like the skate shoe business, some retailers realize that styling instead of function frequently drives sales of individuals footwear.
"At this time the merchandise is a lot more visual than function," stated Chet James, gm of Super Jock 'N Jill, Dallas, speaking about trailrunning footwear. Still, James noted the current hype over adventure sports helps draw more customer traffic. "The marketing campaigns and media help bring growing figures of people in, nonetheless they frequently occasions day an issue that increases results on their own account,Inch he conceded.
John Wilkinson, executive vp inside the 85-store chain Track 'N Trail, Eldorado Hillsides, Calif., stated the shop has "seen some activity in approach footwear," but he requested the amount of consumers depend in it commercially sport. And, instead of accelerating total footwear business, Wilkinson speculated elevated sales of approach footwear and trailrunners are gnawing away at traditional hiking shoe and boot volume.
But Dan Bazinet, president of Overland Exchanging, a 34-store chain situated in Westford, Mass., believes the company-new looks have breathed existence for the wilting hiking boot category. "[Approach-type footwear] don't represent the lion's participate the hiking market, nonetheless they have elevated the hiking business and provided us extra sales," Bazinet stated.
He designated Timberland's Treeline Series and Rockport's Leadville line as strong performers. Unsurprisingly, he noted the company-new looks are attractive to youthful consumer base than traditional hikers.
For that month of June, sales of men's hikers were up 49 percent at Overland, rather of June '95, while sales of women's hikers were up 17 % for that month. Bazinet also attributed elevated sales that shops walked inside the hiking business, departing that business for that specialists.
Some retailers draw a good example concerning the hiking boom of two yrs ago combined with the current extreme sport phenomenon. "Plenty of bigger chains will get a specific percent in the industry while [extreme] sports remain a fad because they are selling cost-point type gear," described Steven Carre, assistant hard goods buyer at Adventure 16, a six-store chain situated in Hillcrest.
"However individuals [true enthusiasts] will say `we need real gear' and may shown up at us. That will help us after a while. What Size Skateboard good for an 3 4 5 6 7 8 9 10 11 12 13 14 year old
…
2d grid from
grasshopper but in 3d, fully controllable of course. I want to do something
like the image in this web
site:http://news.cnet.com/Photos-Weaving-high-tech-fabrics-of-the-future—page-12/2009-1008_3-5667576-12.html
I figured that connecting points and lines kind of works (point and line input AB command) but the line length changes when I move a
point. What I want to be able to do is to move a point and drag others but keep
the line segments constant, just as a real net.
…
Added by Jesus Garza at 8:28am on February 23, 2010
ehow acquire different settings/are calculated differently. Appears at random “rows” of points, sometimes it all works fine, so I need to do a series for the error to show. See images below.
In the Ladybug fly run the VT of the window changes.
It’s taken me a day and a half to track this error down. Phew.
I get the same error on two different comps.
What is causing this? Does anyone get the same error? Images below created with RADquality set to 2, and 7 cores. Fiddling with Radsettings dont help, I think, except error goes away with very low ab.
…
d the fact that one pipe goes out and one goes in, that the surface normal direction is opposite for the two surfaces? Based on an earlier thread, you should know why by now. The two curves have opposite directions (again!); see the white arrows using Rhino 'Analyze | Direction'?
As before, you can fix that by flipping one curve to match the other. HOWEVER, you connected your curves directly to the 'Divide' components instead of using 'Crv' geometry params - bad form. And as before, you "fixed it" by reversing the list of starting points ('S' input to 'BiArc'). Better like this - 'Crv' params are internalized, no need for Rhino file:
Well, well! That didn't fix the opposite surface normals after all! Trust me, though, using geometry params and being conscious about matching curve directions is "best practice". But I haven't lofted 'BiArc' curves for awhile, it's late and I want to move on. OH! I just noticed that you reversed the 'Z' direction for one half of the 'BiArc' - that explains it:
Moving on... You've basically got it, though I would do it differently - same result, like this:
I haven't really explained surface normal vectors - can you figure it out from here? One more little wrinkle (Normal_2017Mar17b.gh):
…
Added by Joseph Oster at 12:03am on March 18, 2017
ported to Rhino and "set" in Grasshopper, i trim both surfaces from their rectangular bases so that when sDivide is used it creates and distributes the same number of points on each surface.But heres the problems: a) if i use the "trimmed" surfaces with SrfGrid it errors warning: "A point in the grid is null. fitting operation aborted".I'd learned this was caused by "nulls" replacing position Data Items when the rectangular grid(surface base) was trimmed away. So i used Clean Tree which worked removing all nulls, then Shift Paths\Flip Matrix to create line-endpoint pairs for Polyline\Evaluate Curve. I Flattened the last Flip Matrix placing all data items in one source for SrfGrid, like in the working Untrim\CopyTrim definition.This time,.b) SrfGrid errored with: "The UCount value is not valid for this amount of points",.So, i substituted a 356 value, numeric Slider in the Addition B param., and tested its range until a valid UCount was found. Then SrfGrid fitted a surface thru the points, BUT,d) those SrfGrid surfaces are extremely deformed even thought the points preceding it from Evaluate Curve are accurate,SEE: def: "3b-RGH_SurfaceBlend.gh",AND,.a2) if i use Untrim with CopyTrim then SrfGrid works, but since the Jokers limbs WILL be in different surface positions then the blends between the Arm (for example) will rise from its relative FLAT position on the untrimmed Source surface to the Arm on the Target surface, rather than morphing from the Corresponding Arm position on the Source surface,. ..see def.: "4-RGH_SurfaceBlend.gh"So please let me know,..1) how to produce accurate surfaces from SrfGrid in def.: "3b-RGH_SurfaceBlend.gh",. ..(NOTE: BOTH these def's contain 2 indentical, "internalized" surfaces, but if def. 3b can be made to work it will also work with Dis-similar surfaces)2) which component to use or how else to determine the correct UCount value for a specified amount of points(ie:155), re: SrfGrid error: "The UCount value is not valid for this amount of points",.3) how else to force SrfGrid to work with Trimmed surfaces?, AND,..4) how to force intersurface, point-blend correspondence lines: Polylines(PLine) to be connected between correctly! correponding positions (Limbs) on the surfaces?,
Really! appreciate all help, definitions and kind generosity common to this knowledgable membership,
Cheers!,
Jeff…