ported to Rhino and "set" in Grasshopper, i trim both surfaces from their rectangular bases so that when sDivide is used it creates and distributes the same number of points on each surface.But heres the problems: a) if i use the "trimmed" surfaces with SrfGrid it errors warning: "A point in the grid is null. fitting operation aborted".I'd learned this was caused by "nulls" replacing position Data Items when the rectangular grid(surface base) was trimmed away. So i used Clean Tree which worked removing all nulls, then Shift Paths\Flip Matrix to create line-endpoint pairs for Polyline\Evaluate Curve. I Flattened the last Flip Matrix placing all data items in one source for SrfGrid, like in the working Untrim\CopyTrim definition.This time,.b) SrfGrid errored with: "The UCount value is not valid for this amount of points",.So, i substituted a 356 value, numeric Slider in the Addition B param., and tested its range until a valid UCount was found. Then SrfGrid fitted a surface thru the points, BUT,d) those SrfGrid surfaces are extremely deformed even thought the points preceding it from Evaluate Curve are accurate,SEE: def: "3b-RGH_SurfaceBlend.gh",AND,.a2) if i use Untrim with CopyTrim then SrfGrid works, but since the Jokers limbs WILL be in different surface positions then the blends between the Arm (for example) will rise from its relative FLAT position on the untrimmed Source surface to the Arm on the Target surface, rather than morphing from the Corresponding Arm position on the Source surface,. ..see def.: "4-RGH_SurfaceBlend.gh"So please let me know,..1) how to produce accurate surfaces from SrfGrid in def.: "3b-RGH_SurfaceBlend.gh",. ..(NOTE: BOTH these def's contain 2 indentical, "internalized" surfaces, but if def. 3b can be made to work it will also work with Dis-similar surfaces)2) which component to use or how else to determine the correct UCount value for a specified amount of points(ie:155), re: SrfGrid error: "The UCount value is not valid for this amount of points",.3) how else to force SrfGrid to work with Trimmed surfaces?, AND,..4) how to force intersurface, point-blend correspondence lines: Polylines(PLine) to be connected between correctly! correponding positions (Limbs) on the surfaces?,
Really! appreciate all help, definitions and kind generosity common to this knowledgable membership,
Cheers!,
Jeff…
diseño, construcción y entendimiento de nuestro entorno.
BIM está poniendo a disposición de los diseñadores y gestores auténticas bases de datos que pueden generarse, conectarse y editarse de forma paramétrica, proporcionando una sólida capa de realidad a los ejercicios de diseño generativo y computación que son objeto de estudio en Algomad, el seminario que busca popularizar la programación y la parametrización en el diseño y en la experiencia de nuestro entorno construido.
Tras un paréntesis en 2015, Algomad vuelve con el objetivo de demostrar cómo una visión computacional del BIM es una oportunidad para mejorar la forma de trabajar de ingenieros, arquitectos, constructoras y operadores de edificios e infraestructuras, tendiendo un puente entre las técnicas de diseño digital más avanzadas y la realidad de la construcción.
Algomad 2016 tendrá lugar en el centro de Madrid, en IE School of Architecture and Design, IE University, los días 3, 4 y 5 de Noviembre de 2016 y comprenderá 4 talleres así como ponencias a cargo de expertos de primer nivel.
Estructura de Algomad 2016
Algomad 2016 se estructura en torno a tres áreas temáticas principales:
BIM, como la metodología total específica para el sector de la construcción.
Computación, englobando las aplicaciones de programación y parametrización al diseño de edificios e infraestructuras.
Realidad, como marco de trabajo, buscando siempre resolver problemas reales a través de los dos puntos anteriores.
Público objetivo
Arquitectos, arquitectos técnicos, ingenieros y en general académicos, estudiantes de últimos cursos y profesionales del mundo inmobiliario y de la construcción que compartan un interés por la digitalización de nuestro sector. Se espera un nivel mínimo en el uso de herramientas BIM y de parametrización. Algomad proporcionará formación adicional y gratuita en las herramientas básicas a emplear en los talleres para asegurar un correcto desempeño.…
te some implications and questions so I will go one by one:
"Now I would like to use a single VRay material as a template for creating multiple identical materials"I hope this will work, but as VRay does not expose any SDK, I would not guarantee any specific result.
"Now I need to add them to the document material table"This is done with a reference to a document instance, such as the one you get with the code doc.Materials (both in C# and Vb.Net).
"I'm not going to learn C# to modify his script"That's a pity, it would be nice to pass on this troublemaker to somebody else! :)Btw, C# and Vb.Net are very very similar. This script could be written in Vb.Net too.
"Reference to a non-shared member requires an object reference. (line 96)"This only means that you need to access the Materials property on an instance, not on the type (class) name. Change that line using what is written at point 2.
"Do I understand that the material has to be assigned to a particular object in order to enter the Material Table?"No it does not. But if you call the _Purge command it will be removed if it does not have an object that references it.
"Can I assign it to a Layer instead?"You do not need to. But this would be achieved with doc.Layers[whichLayer].RenderMaterialIndex = materialIndex; in C# or doc.Layers(whichLayer).RenderMaterialIndex = materialIndex in Vb.Net.
"Any ideas? A better way to do this?"If you found a way to bypass the VRay SDK not being there, this should work.
"Giulio's component has a type hint defined as a Material"It does not any longer. The hint was there in earlier versions of Grasshopper, but now the hint has disappeared. This is not so bad, and it is also the only way you would be able to use either a Material instance already or a string for a material name.
"How was that done?"Probably it was done in an older version of Grasshopper. But which version are you using?
"I can't figure out how to cast the input as a Rhino.DocObjects.Material, so you can see that I have cast it as a compatible type in the first 2 lines... is there a cleaner way?"That sounds like a good way actually. Be sure your component responds properly when something wrong is inputted, though.Dim mTemp As Rhino.DocObjects.Material = CType(M, Rhino.DocObjects.Material)in one line might also work. See msdn for more conversion operators and functions.
I hope this helps,
- Giulio_______________giulio@mcneel.com…
mmon.sdk ,but i herad its used in rhino5.
or example: the book grasshopper primer second edition ,page 98
i dont know what is the "doc.absolutetolerance" and where i can find about it....i dont kow it should be a class or a fuction,i tried to search the rhino4. net sdk,i cant find it ....maybe its my searching problem.
but according to the grasshopper primer, i indeed know many kind of Variables,many functions,basic structure, loops, and conditions,and what is onutil.xxxx and rhutil.xxxx.but i found all this imformation is not helpful enough to me when reading the examples downloaded from many disscussions.when i found a new variable or new funcion,i dont know where i can find the introduction about them,such as the upper coding:"doc.absolutetolerance".i tried to use the auto complete such as
dim xxxx as oncurve
xxxx. to find the class oncurve's funtions and variables ,but its too uneffcient.
-----------------------------------------------
And,i dont know the difference between the components vb script and dotnet vb script....
because i found when i type onutil. the auto complete has noting appear...and the variables declaring is not the same. in vb script dim xxxx as curve but in dotnet vb script its dim xxxx as oncurve,which is the same as the grasshopper primer teached me...but i guess.... the vb script component is just like the rhinoscript(not the same),and the dotnet vb script is more powerful than it. am i right?
------------------------------------------------
at last i dont know these.
Imports System Imports System.IO Imports System.Xml Imports System.Data Imports System.Drawing Imports System.Reflection Imports System.Collections Imports System.Windows.Forms Imports Microsoft.VisualBasic Imports System.Collections.Generic Imports System.Runtime.InteropServices
when i search google about them,the introduction about them is too professinal for me to understand......i just want to know what i can do by using them ...
-------------------------
sorry for disturbing you so much!!!
best regards!
yours truly
YUAN.T
…
lts.
In the visualization, points is an interesting option. It's a matter of aesthetics I guess, I go with surfaces :) Also what you can try is selecting Filters -> Slice (you can also find it in the icons above the pipeline viewer), in the Slice options below the pipeline press Z normal and on the Z coordinate press some height relevant to the buildings (e.g. 1.75m a typical human scale). That would show you the flow around the buildings on that height. Experiment with selecting other normals and values. Keep playing with the filters there's some cool things in there. Also you can check out the mailing list and extensive paraview documentation.
Concerning the errors I apologize because I just downloaded your case.
It appears that the decomposeParDict is not included in the system folder. I am not sure if this is due to BF not going through the whole workflow yet or an ommission on our side. Please feel free to add it in Github. I will also note it down and pass it to Mostaph to check. In the meantime please find attached a VERY detailed decomposeParDict file. I took the liberty to set it at 4 processors (the numberOfSubDomains value) and also selected (that is uncommented) the scotch decomposition method. It's the easiest method to use since it is automatic and doesn't require any more inputs on how the domain is decomposed on the x,y,z directions (which would require you to change values in the attached file).
Now, the different folders created are simply snapshots of the current solution at the specific timestep. To control how often the solver is saving change the writeInterval number in the controlDict file. You can also change almost all these values on the fly, while OF is running.
Finally, concerning the other errors of parafoam it seems somehow parafoam is reading the intial condition names instead of actual results from the solution files and it doesn't like it.
Does this happen only when you open the case (i.e. at 0 time) or does it also happen when you move to an other timestep?
Also, are you using paraFoam, paraview or the paraFoam -builtin method?
The extension of the paraFoam file seems to be .foam which means you are probably using the built in viewer. That might be the issue but I'm not sure.
Can you try running paraview, navigate to your case folder, open the .foam file and see if there is still an error?
Also, if it isn't much trouble can you zip one of the time folders and attach it here? I'd like to take a look at what's inside to check against what the error report says.
Once again thanks for testing!
Kind regards,
Theodore.…
t. So here we go!
1. Honeybee is brown and not yellow [stupid!]...
As you probably remember Honeybee logo was initially yellow because of my ignorance about Honeybees. With the help of our Honeybee expert, Michalina, now the color is corrected. I promised her to update everyone about this. Below are photos of her working on the honeybee logo and the results of her study.
If you think I'm exaggerating by calling her a honeybee expert you better watch this video:
Thank you Michalina for the great work! :). I corrected the colors. No yellow anymore. The only yellow arrows represent sun rays and not the honeybee!
2. Yellow or brown, W[here]TH Honeybee is?
I know. It has been a long time after I posted the initial video and it is not fun at all to wait for a long time. Here is the good news. If you are following the Facebook page you probably now that the Daylighting components are almost ready.
Couple of friends from Grasshopper community and RADIANCE community has been helping me with testing/debugging the components. I still think/hope to release the daylighting components at some point in January before Ladybug gets one year old.
There have been multiple changes. I finally feel that the current version of Honeybee is simple enough for non-expert users to start running initial studies and flexible enough for advanced users to run advanced studies. I will post a video soon and walk you through different components.
I think I still need more time to modify the energy simulation components so they are not going to be part of the next release. Unfortunately, there are so many ways to set up and run a wrong energy simulation and I really don’t want to add one new GIGO app to the world of simulation. We already have enough of that. Moreover I’m still not quite happy with the workflow. Please bear with me for few more months and then we can all celebrate!
I recently tested the idea of connecting Grasshopper to OpenStudio by using OpenStudio API successfully. If nothing else, I really want to release the EnergyPlus components so I can concentrate on Grasshopper > OpenStudio development which I personally think is the best approach.
3. What about wind analysis?
I have been asked multiple times that if Ladybug will have a component for wind study. The short answer is YES! I have been working with EFRI-PULSE project during the last year to develop a free and open source web-based CFD simulation platform for outdoor analysis.
We had a very good progress so far and our rockstar Stefan recently presented the results of the work at the American Physical Society’s 66th annual DFD meeting and the results looks pretty convincing in comparison to measured data. Here is an image from the presentation. All the credits go to Stefan Gracik and EFRI-PULSE project.
The project will go live at some point next year and after that I will release the Butterfly which will let you prepare the model for the CFD simulation and send it to EFRI-PULSE project. I haven’t tried to run the simulations locally yet but I’m considering that as a further development. Here is how the component and the logo looks like right now.
4. Teaching resources
It has been almost 11 months from the first public release of Ladybug. I know that I didn't do a good job in providing enough tutorials/teaching materials and I know that I won’t be able to put something comprehensive together soon.
Fortunately, ladybug has been flying in multiple schools during the last year. Several design, engineering and consultant firms are using it and it has been thought in several workshops. As I checked with multiple of you, almost everyone told me that they will be happy to share their teaching materials; hence I started the teaching resources page. Please share your materials on the page. They can be in any format and any language. Thanks in advance!
I hope you enjoyed/are enjoying/will enjoy the longest night of the year. Happy Yalda!
Cheers,
-Mostapha
…
phere with the maximum number of triangles but not much than a defined threshold.
I scaled that mesh just to fit Rhino grid, but it is not mandatory. What is useful, is to scale not uniformly the mesh (Scale NU). It could be done after cellular modifier applied or before or before and after. The 3 options are possible in the script. If you don’t need them just put 1 in scale sliders.
Ellipsoid mesh is the populated with points, I put 2 independents populations to randomize a bit further. For each vertices of the mesh the closest distance from the populated points is calculated.
Here is an illustration in color of this distance.
This distance is then used to calculate a bump. If domain for bump is beginning with negatives values to 0, it carves the mesh. Instead it bumps/inflates it.
Some images to illustrate the difference with populating 100 points with one or two populations.
Here some images to illustrate the application of scale before carving or after.
Next phase apply noise. At the moment I don't find it good.…
DP ($$$ aside), GC, and Grasshopper. Arthur’s original question is very important
and the exact question (and hopefully answer) I was hoping to find on a
forum.
“How to take intelligent 3D parametric generative design models (scripting, etc.) into 2D documents?" Or, deliver the 3D design for evaluation, bid, construction, etc.
I am intrigued by Jon’s comments in the same thread and would like to know how I can learn more about the process (and
pitfalls) of turning over a 3D digital generative models to a contractor/fabricator.
Are there any industry guidelines established I could use as a reference to guide our firm through this type of uncharted territory?
Arthur’s question is very reminiscent of 10 years ago when I was frustrated with the amount of time spent on the development of a 3D model design (physical and/or virtual) only to have to wipe the table clean and start the process all over again in 2D in order to document the project for delivery. From this I jumped head first into BIM and Revit, vowing never to go back to unintelligent 2D line work. I am now working on Bentley software (v8i: Microstation and Bentley Architecture) with the access and desire to venture into Generative Components. I am very intrigued by Rhino/Grasshopper primarily with the apparent ease of use and available resources assisting in the learning process – something not really available with Bentley.
In hindsight, as I am doing my software research I think the current use of Revit and BA (Bentley Architecture) are more of a “bridge”
between the past (decades of digital 2D work, i.e. AutoCAD) and where hopefully
we all will be someday in the near future (100% 3D modeling, i.e. Digital
Project??). Without having the experience
it would appear that DP/CATIA (PLM software) are closer to this than any other
type of software. As complicated as the
industry standards are for the automobile and airline industry, I feel we
(architectural industry and others) are heading in a similar direction with
total understanding (PLM/ Evidence Based Design) of a design (a whole other topic). If anything I think the market will begin to
demand it sooner or later.
Gehry (DP) article NY Times:
http://www.nytimes.com/2009/02/11/business/11gehry.html
I know these type of broad discussions (software vs. software) can be blown out of proportion on forums, but I am would like to read
the pulse of those who are already in the trenches (using Grasshopper, CATIA, Digital Project, Generative Components, others??) and hear your thoughts. Just as valuable would be other threads,
industry articles/reviews of 3D parametric generative design software.
Thanks,
Boyd…
Introduzione a Grasshopper", il primo manuale su Grasshopper.
.
I corsi PLUG IT nascono dalla volontà di promuovere le nuove tecnologie digitali di supporto alla progettazione e condividere il know-how maturato attraverso ricerca, collaborazione con i più importanti studi di architettura e pubblicazioni internazionali.
.
Verranno introdotte le nozioni base di Grasshopper approfondendo le metodologie della progettazione parametrica e le tecniche di modellazione algoritmica per la generazione di forme complesse. Il corso è rivolto a studenti e professionisti con esperienza minima nella modellazione 3D e si articolerà in lezioni teoriche ed esercitazioni.
. Argomenti trattati:
- Introduzione alla progettazione parametrica: teoria, esempi, casi studio - Grasshopper: concetti base, logica algoritmica, interfaccia grafica - Nozioni fondamentali: componenti, connessioni, data flow
- Funzioni matematiche e logiche, serie, gestione dei dati - Analisi e definizione di curve e superfici
- Definizione di griglie e pattern complessi - Trasformazioni geometriche, paneling - Attrattori, image sampler
- Data tree: gestione di dati complessi - Digital fabrication: teoria ed esempi - Nesting: scomposizione di oggetti tridimensionali in sezioni piane per macchine CNC
.
Verrà rilasciato un attestato finale.
.
Ulteriori info e programma completo su: www.arturotedeschi.com e su www.samilolab.it…