Horticulture and Landscape in same time.
The most common plastic materials used as agricultural films are the low density polyethylene (LDPE, with a density less than 0.93 kg m−3), the copolymer of ethylene and vinyl-acetate (EVA)
Also here you can find the characteristics of the flexible materials for greenhouse covers (adapted from CPA, 1992 and Tesi, 2001) as much as i get.
UV-PE Film ( UV-PE~ polyethylene Long life or UV)
Thickness (mm) = 0.18
Direct PAR transmissivity (%) = 90
Diffuse PAR transmissivity (%)= 86
Long-wave IR transmissivity (%)= 65
EVA Film ( EVA~Ethylene vinyl-acetate copolymer)
Thickness (mm) = 0.18
Direct PAR transmissivity (%) = 90
Diffuse PAR transmissivity (%)= 76
Long-wave IR transmissivity (%)= 27
and here you will find the global heat transfer coefficient’ (K in W m−2 °C−1) for the above greenhouse covering materials, measured under normalized conditions (temperatures: exterior: −10°C, interior: +20°C, wind: 4 m s−1). (Source: Nisen and Deltour, 1986.)
Cover Clear sky Overcast Sky
Single PE 8.8-9.0 7.1- 7.2
Single EVA 7.8 6.6
Note : the PAR radiation (photosynthetically active or photoactive radiation and its the amounts to 45–50% of the global radiation; Berninger, 1989)
The name PAR is used to designate the radiation with wavelengths useful for plant photosynthesis. It is accepted that the PAR radiation ranges from 400 to 700 nm (McCree, 1972), although some authors consider the PAR from 350 to 850 nm.
The composition of the radiation changes with time, as a function of the Sun’s elevation and the cloudiness. When the Sun is low over the horizon, the short wavelengths are reduced (less UV and more red). The clouds reduce the amount of energy, greatly decreasing the NIR.
The PAR proportion in relation to the global radiation increases with scattering (diffusion). It is lower with clear sky and in the summer (45–48%).
kind regards
rafat …
ace Syntax." eCAADe 2013 18 (2013): 357.
http://www.sss9.or.kr/paperpdf/mmd/sss9_2013_ref048_p.pdf
The measure Entropy is newer. I hereby explain it (from my PhD dissertation):
Entropy values, as described in (Hillier & Hanson, The Social Logic of Space, 1984) and specified in (Turner A. , “Depthmap: A Program to Perform Visibility Graph Analysis, 2007), intuitively describe the difficulty of getting to other spaces from a certain space. In other words, the higher the entropy value, the more difficult it is to reach other spaces from that space and vice-versa. We compute the spatial entropy of the node as using the point depth set:
(11)
“The term is the maximum depth from vertex and is the frequency of point depth *d* from the vertex” (ibid). Technically, we compute it using the function below, which itself uses some outputs and by-products from previous calculations:
Algorithm 4: Entropy Computation
Given the graph (adjacency lists), Depths as List of List of integer, DepthMap as Dictionary of integer
Initialize Entropies as List(double)
For node as integer in range [0, |V|)
integer How_Many_of_D=0
double S_node=0
For depth as integer in range [1, Depths[node].Max()]
How_Many_of_D=DepthMap.Branch[(node,depth)].Count
double frequency= How_Many_of_D/|V|
S_node = S_node - frequency * Math.Log(frequency, 2)
Next
Entropies [node] = S_node
Next
…
t the maximum potential with the bridge BIM+PARAMETRIC DESIGN ;D
During this Intense Week, we will learn about the power of Rhino + Grasshopper + ArchiCAD with Professional and Useful examples for our Normal Working day :D
You will get Advanced Library Files + Personal Web + Knowledge and Skills to start using this incredible Methodology ;D
Also, the week is having Lectures from different Experts sharing their Computational Working Experiences ;D And Jam Sessions! opening the door to 5 interesting topics to research, learn and experiment together :D
2020 is your YEAR ;D !!!
Complete details and registration……
Introduction to Grasshopper Videos by David Rutten.
Wondering how to get started with Grasshopper? Look no further. Spend an some time with the creator of Grasshopper, David Rutten, to learn the
y case. Here's the thing. There is this subject at my university where we are assigned a famous building and we need to recreate it in Rhino. We're given bonus points if we manage to code some interesting part of it in Grasshopper. So far so good, I'm doing pretty well with Rhino and by far I am happy with the results I've achieved with modelling the given building. Harbin Opera House by MAD is the building I'm trying to model. There is one particular surface:I've built this surface in Rhino and now I'm trying to map pyramids on it. Not only have the pyramids to be different in height, but their height has to be dependent on the curvature of the surface. I'm getting some results but it seems to be exactly the opposite of what I need. I want to have higher/spikier pyramids where my curvature analysis shows red/blue and lower/slopier pyramids where the analysis shows green colour.At the moment I'm not really sure how the code I have works, but it seems that the height of the pyramids is dependent on a distance from a point in space to the projection of the cap-point of a pyramid.Here're my Rhino and Grasshopper files:surface1.3dm
surface1.ghI'd be grateful if someone of you guys could handle my problem. I've got one more issue with this surface, but once I get a solution to the first 1 will let know what the second one is.Thanks in advance and keep well!…
lts.
In the visualization, points is an interesting option. It's a matter of aesthetics I guess, I go with surfaces :) Also what you can try is selecting Filters -> Slice (you can also find it in the icons above the pipeline viewer), in the Slice options below the pipeline press Z normal and on the Z coordinate press some height relevant to the buildings (e.g. 1.75m a typical human scale). That would show you the flow around the buildings on that height. Experiment with selecting other normals and values. Keep playing with the filters there's some cool things in there. Also you can check out the mailing list and extensive paraview documentation.
Concerning the errors I apologize because I just downloaded your case.
It appears that the decomposeParDict is not included in the system folder. I am not sure if this is due to BF not going through the whole workflow yet or an ommission on our side. Please feel free to add it in Github. I will also note it down and pass it to Mostaph to check. In the meantime please find attached a VERY detailed decomposeParDict file. I took the liberty to set it at 4 processors (the numberOfSubDomains value) and also selected (that is uncommented) the scotch decomposition method. It's the easiest method to use since it is automatic and doesn't require any more inputs on how the domain is decomposed on the x,y,z directions (which would require you to change values in the attached file).
Now, the different folders created are simply snapshots of the current solution at the specific timestep. To control how often the solver is saving change the writeInterval number in the controlDict file. You can also change almost all these values on the fly, while OF is running.
Finally, concerning the other errors of parafoam it seems somehow parafoam is reading the intial condition names instead of actual results from the solution files and it doesn't like it.
Does this happen only when you open the case (i.e. at 0 time) or does it also happen when you move to an other timestep?
Also, are you using paraFoam, paraview or the paraFoam -builtin method?
The extension of the paraFoam file seems to be .foam which means you are probably using the built in viewer. That might be the issue but I'm not sure.
Can you try running paraview, navigate to your case folder, open the .foam file and see if there is still an error?
Also, if it isn't much trouble can you zip one of the time folders and attach it here? I'd like to take a look at what's inside to check against what the error report says.
Once again thanks for testing!
Kind regards,
Theodore.…
mmon.sdk ,but i herad its used in rhino5.
or example: the book grasshopper primer second edition ,page 98
i dont know what is the "doc.absolutetolerance" and where i can find about it....i dont kow it should be a class or a fuction,i tried to search the rhino4. net sdk,i cant find it ....maybe its my searching problem.
but according to the grasshopper primer, i indeed know many kind of Variables,many functions,basic structure, loops, and conditions,and what is onutil.xxxx and rhutil.xxxx.but i found all this imformation is not helpful enough to me when reading the examples downloaded from many disscussions.when i found a new variable or new funcion,i dont know where i can find the introduction about them,such as the upper coding:"doc.absolutetolerance".i tried to use the auto complete such as
dim xxxx as oncurve
xxxx. to find the class oncurve's funtions and variables ,but its too uneffcient.
-----------------------------------------------
And,i dont know the difference between the components vb script and dotnet vb script....
because i found when i type onutil. the auto complete has noting appear...and the variables declaring is not the same. in vb script dim xxxx as curve but in dotnet vb script its dim xxxx as oncurve,which is the same as the grasshopper primer teached me...but i guess.... the vb script component is just like the rhinoscript(not the same),and the dotnet vb script is more powerful than it. am i right?
------------------------------------------------
at last i dont know these.
Imports System Imports System.IO Imports System.Xml Imports System.Data Imports System.Drawing Imports System.Reflection Imports System.Collections Imports System.Windows.Forms Imports Microsoft.VisualBasic Imports System.Collections.Generic Imports System.Runtime.InteropServices
when i search google about them,the introduction about them is too professinal for me to understand......i just want to know what i can do by using them ...
-------------------------
sorry for disturbing you so much!!!
best regards!
yours truly
YUAN.T
…
lla progettazione parametrica e le tecniche di modellazione algoritmica per la generazione di forme complesse
___________________________________________________________________________________
luogo:
Sala meeting Hotel Mercure Milano Centro Piazza Oberdan 12 – 20129 MILANO
Scadenza iscrizioni: 12 Novembre 2011 – ore 15.00
___________________________________________________________________________________
info e prenotazioni:
Le Penseur (coordinamento formazione)
info@lepenseur.it
081 564 21 84
347 548 71 78
quote di partecipazione e programma (formato PDF)
ulteriori informazioni sui corsi PLUG > IT
___________________________________________________________________________________
PROGRAMMA DEL CORSO
GIORNO_01
10.00 – 10.30: presentazione workshop
10.30 – 11.30: introduzione alla progettazione parametrica: teoria, esempi, casi studio
11.30 – 13.00: Grasshopper: concetti base, logica algoritmica, interfaccia grafica
13.00 – 14.00: break | lunch
14.00 – 16.00: nozioni fondamentali: componenti, connessioni, data flow
16.00 – 18.00: esercitazione
GIORNO_02
10.00 – 12.00: funzioni matematiche e logiche, serie, gestione dei dati
12.00 – 15.00: analisi e definizione di curve e superfici
GIORNO_03
10.00 – 12.00: definizione di griglie e pattern complessi
12.00 – 13.00: trasformazioni geometriche, paneling
13.00 – 14.00: break | lunch
14.00 – 16.00: esercitazione
16.00 – 18.00: attrattori, image sampler
GIORNO_04
10.00 – 13.00: data tree: gestione di dati complessi
13.00 – 14.00: break | lunch
14.00 – 15.00: digital fabrication: teoria ed esempi
15.00 – 18.00: nesting: scomposizione di oggetti tridimensionali in sezioni e posizionamento su piani di taglio per macchine a controllo numerico CNC…
aggie experiences her first love, her father leaves her mother at Christmas as a child. After her ex-husband leaves her family at Christmas twenty years later, Maggie forms a protective shield over her heart and her son, Jordan. Jordan, however, sees that Maggie is lonely, and writes letters to God praying for her happiness. Jordan's prayers are answered when Maggie meets his tutor, widower Casey, and forms an instant connection that is stronger than the one she has with Tanner, the fellow divorce attorney she had been dating. When Maggie and Casey begin to fall in love, though, Maggie pulls back. After discovering a coincidental childhood connection with Casey, and reading Jordan's letters to God, though, Maggie must decide if Christmas is the right time to open her heart to love.
We hope you enjoy and fun here. so do not miss to watch and visit Karen Kingsbury's Maggie's Christmas Miracle Online for free on Monday. It’s up to you, you can watch it streaming via the Internet, or through a television at home. You don’t need to install anything and you can Watch Karen Kingsbury's Maggie's Christmas Miracle in very good quality.
watch Karen Kingsbury's Maggie's Christmas Miracle Online
watch Karen Kingsbury's Maggie's Christmas Miracle Online Free
watch Karen Kingsbury's Maggie's Christmas Miracle
Karen Kingsbury's Maggie's Christmas Miracle
Karen Kingsbury's Maggie's Christmas Miracle Free
Karen Kingsbury's Maggie's Christmas Miracle Streaming
Stream Karen Kingsbury's Maggie's Christmas Miracle
watch Karen Kingsbury's Maggie's Christmas Miracle Stream
watch Karen Kingsbury's Maggie's Christmas Miracle Free
watch Online Karen Kingsbury's Maggie's Christmas Miracle
watch Karen Kingsbury's Maggie's Christmas Miracle Full Video
Karen Kingsbury's Maggie's Christmas Miracle Megavideo
Karen Kingsbury's Maggie's Christmas Miracle Putlocker
Karen Kingsbury's Maggie's Christmas Miracle Megashare
Karen Kingsbury's Maggie's Christmas Miracle Youtube
Karen Kingsbury's Maggie's Christmas Miracle Dailimotion
Karen Kingsbury's Maggie's Christmas Miracle Xvid
Karen Kingsbury's Maggie's Christmas Miracle Player
Karen Kingsbury's Maggie's Christmas Miracle Vidto
Karen Kingsbury's Maggie's Christmas Miracle played…
Added by rogerdanuarta at 11:34am on December 13, 2017