it seems that was this. Now all is working fine !
Glad that it worked! But I am still a bit worried. Gismo components only modify the gdal-data/osmconf.ini file and no other MapWinGIS file. So your MapWinGIS installation files should not be compromised. The fact that you did not get the "COM CLSID" error message when running the "Gismo Gismo" component suggests that MapWinGIS has been properly installed. So I wonder if the cause for the permanent "invalid shapes" warning has again something with the fact that your system is again not allowing the MapWinGIS to properly edit the osmconf.ini. Maybe this problem will appear again, and again, and reinstallation of MapWinGIS every time can be somewhat bothersome.
- About the terrain generation, is it possible to have the texture from google or other provider mapped onto the terrain surface from gismo component ? (Same as using the ladybug terrain generator in fact). I try to used the image extracted by ladybug component and then applied it to the gismo terrain but the texture is rotated by 90°.
The issue with the rotation can be solved by swapping/reversing the U,V directions of the terrain surface. A slightly more important issue is that terrain surface generated with Gismo "Terrain Generator" component might have a bit smaller radius than what the radius_ input required. This stems from the fact that the terrain data first needs to be downloaded in geographic coordinate system, and then projected. Some projecting issues may occur at the very edges of the projected terrain, so I had to slightly cut out the very edges of the terrain which results in the actual terrain diameters being slightly shorted in both directions. This means that if you apply the same satellite image from Ladybug "Terrain Generator" component to Gismo "Terrain Generator" component the results may not be the same.I attached below a python component which tries to solve this issue by extending the edges of Gismo "Terrain Generator" terrain, and then cutting them with the cuboid of the exact dimensions as the radius_ input. Have in mind that this extension of the original terrain at its edges is not a correct representation of the actual terrain in that location. But rather just an extension of the isoparameteric curve of the terrain surface. So basically: some 0 to 10% (0 to 10 percent of the width and length) of the terrain around all four edges is not the actual terrain for that location, but rather just its extension.The python component is located at the very right of the definition attached below.
Also, if you would like to use the satellite images from Ladybug "Terrain Generator" component along with "OSM shapes", sometimes you may find slight differences in position of the shapes. This is due to openstreetmap data not being based on Google Maps (that's what Ladybug "Terrain Generator" component is using), but rather on Bing, MapQuest and a few others.
- About the requiredKeys_ input of OSM shapes, I understand what you mean and your advice, but in most cases I use it, the component was working fine even without input. I think it's better to extract all tags, values and keys of the selected area, instead of searching for specific ones as I try to find all data related to what I want after, isn't it ? To check what keys are present on the area also.
Ineed, you are correct.I though you were trying to only create a terrain, 3d buildings and maybe find some school or similar 3d building, for these two locations. The recommendation I mentioned previously is due to shapefiles having a limit (2044) to how many keys it can contain. This requires further testing of some big cities locations with maybe larger radii, which I haven't performed due to my poor PC configuration. But in theory, I imagine that it may happen that a downloaded .osm file may have more than 2044 keys. In that case shapefile will only record 2044 of them, and disregard the others. That was my point.But again 2044 is a lot of keys, and I haven't been checking much this in practice. For example, when I set the radius_ to 1000 meters, and use your "3 Rue de Bretonvilliers Paris" location I get around 350 something keys, which is way below the 2044.Another reason why one should use the requiredKeys_ input is to make the Gismo OSM components run quicker: for example, the upper mentioned 350 something keys will result in 350 values for each branch of the "OSM shapes" component's "values" output.Which means if you have 10 000 shapes, the "OSM shapes" component will have 10 000 branches with 350 items on each branch (values). This can make all Gismo OSM components very heavy, and significantly elongate the calculation process.With requiredKeys_ input you may end up with only a couple of tens of items per each branch.Sorry for the long reply.…
Added by djordje to Gismo at 8:57am on June 11, 2017
t. So here we go!
1. Honeybee is brown and not yellow [stupid!]...
As you probably remember Honeybee logo was initially yellow because of my ignorance about Honeybees. With the help of our Honeybee expert, Michalina, now the color is corrected. I promised her to update everyone about this. Below are photos of her working on the honeybee logo and the results of her study.
If you think I'm exaggerating by calling her a honeybee expert you better watch this video:
Thank you Michalina for the great work! :). I corrected the colors. No yellow anymore. The only yellow arrows represent sun rays and not the honeybee!
2. Yellow or brown, W[here]TH Honeybee is?
I know. It has been a long time after I posted the initial video and it is not fun at all to wait for a long time. Here is the good news. If you are following the Facebook page you probably now that the Daylighting components are almost ready.
Couple of friends from Grasshopper community and RADIANCE community has been helping me with testing/debugging the components. I still think/hope to release the daylighting components at some point in January before Ladybug gets one year old.
There have been multiple changes. I finally feel that the current version of Honeybee is simple enough for non-expert users to start running initial studies and flexible enough for advanced users to run advanced studies. I will post a video soon and walk you through different components.
I think I still need more time to modify the energy simulation components so they are not going to be part of the next release. Unfortunately, there are so many ways to set up and run a wrong energy simulation and I really don’t want to add one new GIGO app to the world of simulation. We already have enough of that. Moreover I’m still not quite happy with the workflow. Please bear with me for few more months and then we can all celebrate!
I recently tested the idea of connecting Grasshopper to OpenStudio by using OpenStudio API successfully. If nothing else, I really want to release the EnergyPlus components so I can concentrate on Grasshopper > OpenStudio development which I personally think is the best approach.
3. What about wind analysis?
I have been asked multiple times that if Ladybug will have a component for wind study. The short answer is YES! I have been working with EFRI-PULSE project during the last year to develop a free and open source web-based CFD simulation platform for outdoor analysis.
We had a very good progress so far and our rockstar Stefan recently presented the results of the work at the American Physical Society’s 66th annual DFD meeting and the results looks pretty convincing in comparison to measured data. Here is an image from the presentation. All the credits go to Stefan Gracik and EFRI-PULSE project.
The project will go live at some point next year and after that I will release the Butterfly which will let you prepare the model for the CFD simulation and send it to EFRI-PULSE project. I haven’t tried to run the simulations locally yet but I’m considering that as a further development. Here is how the component and the logo looks like right now.
4. Teaching resources
It has been almost 11 months from the first public release of Ladybug. I know that I didn't do a good job in providing enough tutorials/teaching materials and I know that I won’t be able to put something comprehensive together soon.
Fortunately, ladybug has been flying in multiple schools during the last year. Several design, engineering and consultant firms are using it and it has been thought in several workshops. As I checked with multiple of you, almost everyone told me that they will be happy to share their teaching materials; hence I started the teaching resources page. Please share your materials on the page. They can be in any format and any language. Thanks in advance!
I hope you enjoyed/are enjoying/will enjoy the longest night of the year. Happy Yalda!
Cheers,
-Mostapha
…
DP ($$$ aside), GC, and Grasshopper. Arthur’s original question is very important
and the exact question (and hopefully answer) I was hoping to find on a
forum.
“How to take intelligent 3D parametric generative design models (scripting, etc.) into 2D documents?" Or, deliver the 3D design for evaluation, bid, construction, etc.
I am intrigued by Jon’s comments in the same thread and would like to know how I can learn more about the process (and
pitfalls) of turning over a 3D digital generative models to a contractor/fabricator.
Are there any industry guidelines established I could use as a reference to guide our firm through this type of uncharted territory?
Arthur’s question is very reminiscent of 10 years ago when I was frustrated with the amount of time spent on the development of a 3D model design (physical and/or virtual) only to have to wipe the table clean and start the process all over again in 2D in order to document the project for delivery. From this I jumped head first into BIM and Revit, vowing never to go back to unintelligent 2D line work. I am now working on Bentley software (v8i: Microstation and Bentley Architecture) with the access and desire to venture into Generative Components. I am very intrigued by Rhino/Grasshopper primarily with the apparent ease of use and available resources assisting in the learning process – something not really available with Bentley.
In hindsight, as I am doing my software research I think the current use of Revit and BA (Bentley Architecture) are more of a “bridge”
between the past (decades of digital 2D work, i.e. AutoCAD) and where hopefully
we all will be someday in the near future (100% 3D modeling, i.e. Digital
Project??). Without having the experience
it would appear that DP/CATIA (PLM software) are closer to this than any other
type of software. As complicated as the
industry standards are for the automobile and airline industry, I feel we
(architectural industry and others) are heading in a similar direction with
total understanding (PLM/ Evidence Based Design) of a design (a whole other topic). If anything I think the market will begin to
demand it sooner or later.
Gehry (DP) article NY Times:
http://www.nytimes.com/2009/02/11/business/11gehry.html
I know these type of broad discussions (software vs. software) can be blown out of proportion on forums, but I am would like to read
the pulse of those who are already in the trenches (using Grasshopper, CATIA, Digital Project, Generative Components, others??) and hear your thoughts. Just as valuable would be other threads,
industry articles/reviews of 3D parametric generative design software.
Thanks,
Boyd…
ting at multiple geometries in the same location. I simply sorted the list of values and used the Delete Consecutive component. This potentially rearranges the order of values but I don't think that matters in your case. I also threw in an Int component which actually seems to make a difference (try sidestepping it and you will see!).
2-I flattened the output of the mesh component before sending it to union. This ensures that the original mesh is booleaned once with all the components rather than individually with each of the 86 components.
Is this what the result should look like?
One suggestion for future postings: when referencing geometry in rhino, it often helps if you attach your rhino file as well so people don't have to guess where you are starting from.
If you have further questions, just ask ;-)
cbass…