n account of the position of the sun and weather cannot be expressed in terms of a single set of luminous intensity values (which is what IES files do).
With regards to your example files, I agree with Chris. The primary reason for the low illuminance levels is that the light bounces are getting lost in the tube. Have you checked with the manufacturer/distributor if the location of the IES file should be inside the tube and not flush with the ceiling? Physically modelling such tubes in lighting software like Radiance (which is what HB uses) or AGI32 is a fairly expensive proposition. This is one of the reasons why manufacturers provide photometric data for such devices (however simplistic that data might be).
The candelamultiplier increases or decreases the luminous intensity values. So it will have a direct impact on the calculation. The primary reason for having that input was to enable users to do some testing with different lamp types and environmental factors such as dirt depreciation. You need not change them for your simulation. Assuming that the IES file is inside the tube, in order to make this calculation work inside HB you'd have to crank up the calculation settings to a very high level (start with -ab 10 -ad 4096).
Finally, due to shortcomings in the annual simulation software (Daysim), IES files will not work directly work with annual calculations. However, there is a fairly easy workaround for that issue. In case you are planning to run annual calculations with IES files, please let us know here.
Sarith…
ing illuminance and limiting exposure (lux hours). Hours with direct solar irradiance are likely to exceed the limiting illuminance thresholds, which range from (200 to 50 lux as per Table 3.4 in CIE 157:2004). It makes sense to consider direct illuminance (an ab=0 simulation in Honeybee) separately from a normal illuminance calculation.
Assuming that the museum exhibits have low to high responsivity to light, an ideal solution would minimize direct sunlight. For daylight from the sky and reflected light, it might be enough to keep the illuminance levels below the recommended thresholds and then sum up lux-hours.
Daysim, the annual daylighting engine used by Honeybee and DIVA, is not very accurate for direct-sun calculations. You will get more accurate results if you run your analysis with Radiance directly.
Instead of considering the horizontal illuminance grids, one can create grids that correspond to the dimensions of the exhibit and then average those values. I think single points, as shown in your gh file might not suffice. Calculating lux-hours is by far the simplest part of such a simulation. It will only require averaging these points, extracting them into an array and then summing up that array.…
starting as soon as possible.
We're offering challenging projects, insights and contact to leading industry companies, project responsibilities according to abilities and initiative, great work environment and laid-back atmosphere, room to play and evolve,...
Our ideal candidate:
- is passionate about construction, engineering and (computational) design
- is proficient in Rhino / Grasshopper / (GH-)Python
- knows his ways around the Adobe Suite and MS Office
- has a current work permit for Germany
- is a German speaker (other native speakers also welcome, with excellent English skills)
- has an architectural background (Student / BA / MA /...), ideally with work experience
- is interested / has experience in digital manufacturing and prototyping
- will be able to join us shortly
We're looking forward to your applications / inquiries / CVs to: mpelzer@fat-lab.de
View our past projects here: www.fat-lab.com
(Current projects, unfortunately, are non-disclosed)
…
mers considering extreme sports reject mainstream retailers and like to check out small stores rather of at chains plus malls. Several smaller retailers discuss trends in sports shoe sales. http://skateszone.com/
Though athletic shoes and sports stores and from doorways retailers have reported somewhat uptick in footwear sales due to the increase in extreme sports, the particular beneficiaries inside the trend are independent surf and skate niche stores.
Some West Coast surf and skate shops stated teenagers and even more youthful Generation Xers are not only rejecting traditional sports, but they're also shunning mainstream retailers and malls meant for smaller niche shops transporting hard-to-come-by brands.
Eddie Miyoshi, district manager at Atomic Garage, a 3-store chain situated in Gardena, Calif., stated the soaring recognition of skateboard footwear has boosted the retailer's total footwear business 20-thirty percent this year, rather of '95.
Skate footwear presently represent 80-90 % of Atomic Garage's shoe sales, while couple of years back, Dr. Martens and Timberland drove the retailer's footwear business.
Like many retailers, Miyoshi pointed to Airwalk since the trend's catalyst.
However, if Airwalk broadened its distribution to larger chains, which are frequently located in malls, only a few skate shoe customers adopted. Rather, many youthful males have switched for your skate shops for additional elusive brands like Etnies, Duffs, and Electricity Footwear by Circus. By refusing to market bigger retailers or sports stores, these brands are increasing their cachet among youthful consumers.
"Kids don't want stuff which have been within the shops,In . Miyoshi added.
Searching ahead, Miyoshi forecasted skate shoe sales will remain strong through spring '97 provided "the [hot] vendors don't auction other [non-particularly shop] retailers."
"Skaters and non-skaters are rebelling against mainstream retailers so on to surf and skate shops for many looks," echoed Mark Richards, co-online sources Val Surf, a 3-store chain situated in North Hollywood, Calif. Soaring sales of skate footwear have driven total footwear receipts up 25 percent this year rather of '95.
"The quantity of that increase might be connected while using exposure of maximum games? I am unsure. [Skate footwear] may also be actually the think about the moment,In . Richards acknowledged. And in relation to getting this right look, youthful customers can be very picky.
"Skateboard footwear is a huge category for people, but we're not able to own the brands, Etnies, Duffs, Electricity and Nice, simply because they won't sell us," stated Mark Anderson, buyer at Chick's Sports, a six-store chain in Covina, Calif. "We have people coming every single day requesting them." Consequently, skate footwear have consistently ongoing to obtain about 5 % of Chick's overall footwear business. http://skateszone.com/the-top-8-best-skateboards-for-beginners-reviews-2017/
Nonetheless, some outdoors, niche sports and sports retailers are noting the growing recognition and coverage of maximum sports will receive a modest impact on footwear sales. Trailrunning footwear and approach/outdoors crosstrainers will be the two groups benefiting the very best inside the recognition. Like the skate shoe business, some retailers realize that styling instead of function frequently drives sales of individuals footwear.
"At this time the merchandise is a lot more visual than function," stated Chet James, gm of Super Jock 'N Jill, Dallas, speaking about trailrunning footwear. Still, James noted the current hype over adventure sports helps draw more customer traffic. "The marketing campaigns and media help bring growing figures of people in, nonetheless they frequently occasions day an issue that increases results on their own account,Inch he conceded.
John Wilkinson, executive vp inside the 85-store chain Track 'N Trail, Eldorado Hillsides, Calif., stated the shop has "seen some activity in approach footwear," but he requested the amount of consumers depend in it commercially sport. And, instead of accelerating total footwear business, Wilkinson speculated elevated sales of approach footwear and trailrunners are gnawing away at traditional hiking shoe and boot volume.
But Dan Bazinet, president of Overland Exchanging, a 34-store chain situated in Westford, Mass., believes the company-new looks have breathed existence for the wilting hiking boot category. "[Approach-type footwear] don't represent the lion's participate the hiking market, nonetheless they have elevated the hiking business and provided us extra sales," Bazinet stated.
He designated Timberland's Treeline Series and Rockport's Leadville line as strong performers. Unsurprisingly, he noted the company-new looks are attractive to youthful consumer base than traditional hikers.
For that month of June, sales of men's hikers were up 49 percent at Overland, rather of June '95, while sales of women's hikers were up 17 % for that month. Bazinet also attributed elevated sales that shops walked inside the hiking business, departing that business for that specialists.
Some retailers draw a good example concerning the hiking boom of two yrs ago combined with the current extreme sport phenomenon. "Plenty of bigger chains will get a specific percent in the industry while [extreme] sports remain a fad because they are selling cost-point type gear," described Steven Carre, assistant hard goods buyer at Adventure 16, a six-store chain situated in Hillcrest.
"However individuals [true enthusiasts] will say `we need real gear' and may shown up at us. That will help us after a while. What Size Skateboard good for an 3 4 5 6 7 8 9 10 11 12 13 14 year old
…
2d grid from
grasshopper but in 3d, fully controllable of course. I want to do something
like the image in this web
site:http://news.cnet.com/Photos-Weaving-high-tech-fabrics-of-the-future—page-12/2009-1008_3-5667576-12.html
I figured that connecting points and lines kind of works (point and line input AB command) but the line length changes when I move a
point. What I want to be able to do is to move a point and drag others but keep
the line segments constant, just as a real net.
…
Added by Jesus Garza at 8:28am on February 23, 2010
ehow acquire different settings/are calculated differently. Appears at random “rows” of points, sometimes it all works fine, so I need to do a series for the error to show. See images below.
In the Ladybug fly run the VT of the window changes.
It’s taken me a day and a half to track this error down. Phew.
I get the same error on two different comps.
What is causing this? Does anyone get the same error? Images below created with RADquality set to 2, and 7 cores. Fiddling with Radsettings dont help, I think, except error goes away with very low ab.
…
y case. Here's the thing. There is this subject at my university where we are assigned a famous building and we need to recreate it in Rhino. We're given bonus points if we manage to code some interesting part of it in Grasshopper. So far so good, I'm doing pretty well with Rhino and by far I am happy with the results I've achieved with modelling the given building. Harbin Opera House by MAD is the building I'm trying to model. There is one particular surface:I've built this surface in Rhino and now I'm trying to map pyramids on it. Not only have the pyramids to be different in height, but their height has to be dependent on the curvature of the surface. I'm getting some results but it seems to be exactly the opposite of what I need. I want to have higher/spikier pyramids where my curvature analysis shows red/blue and lower/slopier pyramids where the analysis shows green colour.At the moment I'm not really sure how the code I have works, but it seems that the height of the pyramids is dependent on a distance from a point in space to the projection of the cap-point of a pyramid.Here're my Rhino and Grasshopper files:surface1.3dm
surface1.ghI'd be grateful if someone of you guys could handle my problem. I've got one more issue with this surface, but once I get a solution to the first 1 will let know what the second one is.Thanks in advance and keep well!…
lts.
In the visualization, points is an interesting option. It's a matter of aesthetics I guess, I go with surfaces :) Also what you can try is selecting Filters -> Slice (you can also find it in the icons above the pipeline viewer), in the Slice options below the pipeline press Z normal and on the Z coordinate press some height relevant to the buildings (e.g. 1.75m a typical human scale). That would show you the flow around the buildings on that height. Experiment with selecting other normals and values. Keep playing with the filters there's some cool things in there. Also you can check out the mailing list and extensive paraview documentation.
Concerning the errors I apologize because I just downloaded your case.
It appears that the decomposeParDict is not included in the system folder. I am not sure if this is due to BF not going through the whole workflow yet or an ommission on our side. Please feel free to add it in Github. I will also note it down and pass it to Mostaph to check. In the meantime please find attached a VERY detailed decomposeParDict file. I took the liberty to set it at 4 processors (the numberOfSubDomains value) and also selected (that is uncommented) the scotch decomposition method. It's the easiest method to use since it is automatic and doesn't require any more inputs on how the domain is decomposed on the x,y,z directions (which would require you to change values in the attached file).
Now, the different folders created are simply snapshots of the current solution at the specific timestep. To control how often the solver is saving change the writeInterval number in the controlDict file. You can also change almost all these values on the fly, while OF is running.
Finally, concerning the other errors of parafoam it seems somehow parafoam is reading the intial condition names instead of actual results from the solution files and it doesn't like it.
Does this happen only when you open the case (i.e. at 0 time) or does it also happen when you move to an other timestep?
Also, are you using paraFoam, paraview or the paraFoam -builtin method?
The extension of the paraFoam file seems to be .foam which means you are probably using the built in viewer. That might be the issue but I'm not sure.
Can you try running paraview, navigate to your case folder, open the .foam file and see if there is still an error?
Also, if it isn't much trouble can you zip one of the time folders and attach it here? I'd like to take a look at what's inside to check against what the error report says.
Once again thanks for testing!
Kind regards,
Theodore.…
radiance parameters to get rid of blotching. To add another level of complexity to my problem, I am running simulations with a translucent material with the following properties: void trans testTrans
0
0
7 0.478 0.478 0.478 0.000 0.010 0.178 0.635
I have had no issues with the renderings when I use clear glazing, as seen on this image:
However the blotching-issue becomes very noticeable when I introduce translucent glazing into the scene:
For the two above cases I used the following parameters:
_av_ is set to 0
xScale is set to 2
_ab_ is set to 6
_dc_ is set to 0.5
_aa_ is set to 0.2
_ad_ is set to 2048
_st_ is set to 0.5
yScale is set to 2
_ps_ is set to 4
_ar_ is set to 64
_as_ is set to 2048
_ds_ is set to 0.25
_pt_ is set to 0.1
_dr_ is set to 1
_pj_ is set to 0.9
_dp_ is set to 256
_dt_ is set to 0.25
_lr_ is set to 6
_dj_ is set to 0.5
_lw_ is set to 0.01
I ran another test with increased Radiance parameters and got the following output:
with the following parameters:
_av_ is set to 0
xScale is set to 6
_ab_ is set to 6
_dc_ is set to 0.75
_aa_ is set to 0.1
_ad_ is set to 4096
_st_ is set to 0.15
yScale is set to 6
_ps_ is set to 2
_ar_ is set to 128
_as_ is set to 4096
_ds_ is set to 0.05
_pt_ is set to 0.05
_dr_ is set to 3
_pj_ is set to 0.9
_dp_ is set to 512
_dt_ is set to 0.15
_lr_ is set to 8
_dj_ is set to 0.7
_lw_ is set to 0.005
Although the second blotching case is much better than the first, it is still very bad for hours when the sun is lower in the sky. The above images are rendered for a clear sky at 18:00 in Germany in a West-facing room.
Sorry for the long post! Can someone help? Kind regards, Örn
…