TB of RAM. I think I'm going to start a GoFundMe campaign to buy one for myself :)
2- The server's cost is about $13 an hour. I get free access to supercomputer through my university and xsede.org because I earned an NSF Honorable mention last March, however, the supercomputers available through both resources are a little complicated for me to use, as opposed to the one available from amazon that has Microsoft server 2012 already installed.
3- I wanted to run 400 annual glare simulations for 400 different views.
4- I tried a to perform annual glare simulation for one view on my Dell XPS that has Intel Core i7-6700HQ processor and 16GB of system memory. The simulation took 2 hours to complete. Radiance parameter ab was set to 6.
5- I wanted to obtain the batch file for each view so I can run them on the server. So I used the fly component to run all 400 simulations and closed the cmd windows, that wasn't bad ( for me at least) because I asked my son to this job for me, he was just glad to help me :)
6- I created one batch file using this cmd command:
dir /s /b *.bat > runall.bat
This created a file with the path to each .bat file. I edited this file in Notepad++ to include the word "start" at the beginning of each line. This was done using the "find and replace" dialogue box.
7- I split my newly created batch file into 3 batch files, each one has about 130 file names and " start" before the file names.
8- installed radiance on my server
9- Ran the first batch file on the server, this started 130 cmd windows performing my simulations, CPU usage was anywhere between 90% to 100% and about 105 GB of RAMs were used.
10. It took about 5 hours to complete all 130 simulations, I expected to run all in 2 hours but can't complain because this would've taken about 260 hours to run on my laptop. After the simulations done I ran the second and then the third batch files ( total of about 15 hours).
11. I got 400 valid dgb files. Couldn't be happier!
…
he time to work with it.
the project is about facade strips which turns along height. the top angle is
parallel to the facade and the bottom is max. 90 degrees twisted, but the strips
should turn diffrently to achieve more dinamic look.
first i have tried to achieve this by calculating distance between the rotation angle from points of the grid and a single point.
then i have tried to ad some more effecting points and used the distance to the divided surface (the circles are just to control the area of effection):
i manually lofted it.
the result is a bit annoying becouse the points that effect the angle are always visible:
i have triend to solve this by drawing a line and divided it to recieve points along the bottom of the geometry. the result is not working properly:
Anyway,
there must be a better/smoother way to achieve this. i would like to effect the twist of the surfaces by distance to a spline, but im just lost. can you help me please?
the problems im encountering:
0- distance spline to grid to effect the angle
1- list of x/y coordinates and angle of rotation for each point of the grid
2- export points to excel
3- lofting lines in one direction only (x1, x2, x3...)
4- reduce the list data to 2 decimal (0,00)
5- maybe angle from radian to degrees
thx…
ed file and code below:
Color ColorAt(Mesh mesh, int faceIndex, double t0, double t1, double t2, double t3) { // int rc = -1; var color = Rhino.Display.Color4f.Black;
if( mesh.VertexColors.Count != 0) { // test to see if face exists if( faceIndex >= 0 && faceIndex < mesh.Faces.Count ) { /// Barycentric quad coordinates for the point on the mesh /// face mesh.Faces[FaceIndex].
/// If the face is a triangle /// disregard T[3] (it should be set to 0.0).
/// If the face is /// a quad and is split between vertexes 0 and 2, then T[3] /// will be 0.0 when point is on the triangle defined by vi[0], /// vi[1], vi[2]
/// T[1] will be 0.0 when point is on the /// triangle defined by vi[0], vi[2], vi[3].
/// If the face is a /// quad and is split between vertexes 1 and 3, then T[2] will /// be -1 when point is on the triangle defined by vi[0], /// vi[1], vi[3]
/// and m_t[0] will be -1 when point is on the /// triangle defined by vi[1], vi[2], vi[3].
MeshFace face = mesh.Faces[faceIndex];
// Collect data for barycentric evaluation. Color p0, p1, p2;
if(face.IsTriangle) { p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.B]; p2 = mesh.VertexColors[face.C]; } else { if( t3 == 0 ) { // point is on subtriangle {0,1,2} p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.B]; p2 = mesh.VertexColors[face.C]; } else if( t1 == 0 ) { // point is on subtriangle {0,2,3} p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.C]; p2 = mesh.VertexColors[face.D]; //t0 = t0; t1 = t2; t2 = t3; } else if( t2 == -1 ) { // point is on subtriangle {0,1,3} p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.B]; p2 = mesh.VertexColors[face.D]; //t0 = t0; //t1 = t1; t2 = t3; } else { // point must be on remaining subtriangle {1,2,3} p0 = mesh.VertexColors[face.B]; p1 = mesh.VertexColors[face.C]; p2 = mesh.VertexColors[face.D]; t0 = t1; t1 = t2; t2 = t3; } }
/** double r = t0 * p0.FractionRed() + t1 * p1.FractionRed() + t2 * p2.FractionRed(); double g = t0 * p0.FractionGreen() + t1 * p1.FractionGreen() + t2 * p2.FractionGreen(); double b = t0 * p0.FractionBlue() + t1 * p1.FractionBlue() + t2 * p2.FractionBlue();
ON_Color color; color.SetFractionalRGB(r, g, b);
unsigned int abgr = (unsigned int)color; rc = (int) ABGR_to_ARGB(abgr); **/ var c0 = new Rhino.Display.Color4f(p0); var c1 = new Rhino.Display.Color4f(p1); var c2 = new Rhino.Display.Color4f(p2); float s0 = (float) t0; float s1 = (float) t1; float s2 = (float) t2;
float R = s0 * c0.R + s1 * c1.R + s2 * c2.R; float G = s0 * c0.G + s1 * c1.G + s2 * c2.G; float B = s0 * c0.B + s1 * c1.B + s2 * c2.B; color = new Rhino.Display.Color4f(R, G, B, 1); } } return color.AsSystemColor(); }
…
Introduzione a Grasshopper", il primo manuale su Grasshopper.
.
I corsi PLUG IT nascono dalla volontà di promuovere le nuove tecnologie digitali di supporto alla progettazione e condividere il know-how maturato attraverso ricerca, collaborazione con i più importanti studi di architettura e pubblicazioni internazionali.
.
Verranno introdotte le nozioni base di Grasshopper approfondendo le metodologie della progettazione parametrica e le tecniche di modellazione algoritmica per la generazione di forme complesse. Il corso è rivolto a studenti e professionisti con esperienza minima nella modellazione 3D e si articolerà in lezioni teoriche ed esercitazioni.
. Argomenti trattati:
- Introduzione alla progettazione parametrica: teoria, esempi, casi studio - Grasshopper: concetti base, logica algoritmica, interfaccia grafica - Nozioni fondamentali: componenti, connessioni, data flow
- Funzioni matematiche e logiche, serie, gestione dei dati - Analisi e definizione di curve e superfici
- Definizione di griglie e pattern complessi - Trasformazioni geometriche, paneling - Attrattori, image sampler
- Data tree: gestione di dati complessi - Digital fabrication: teoria ed esempi - Nesting: scomposizione di oggetti tridimensionali in sezioni piane per macchine CNC
.
Verrà rilasciato un attestato finale.
.
Ulteriori info e programma completo su: www.arturotedeschi.com e su www.edizionilepenseur.it…
te some cut sheets, but not to optmize material, rather define some cut lines. Everything that I am cutting is made of planar wood elements, but there are very specific geometries (mostly straight lines) and I have to put tolerances and radiasas at the corners in order to cut on the cnc mill. Spending time to figure out how to automate is necessary, but I am stuck!
One thing the definition is doing is taking my brep modeled components in rhino and makking them into 2d close curves and laying them side by side. It works...not ideal as its not layed out in a sheet, but that is not the most important part.
Another particular problem is that you will see some notches in the curves, which other pieces will slip into, so different slots need different specific offsets (making them larger) as a toelrance to allow for material play. This I don't even know how to set up so maybe it will just have to wait.
THE MAIN QUESTION, and super important would be, LIFESAVER:
At all 'inward' corners...which I think will always mean concave corners (most are 90 degrees, but are within to sides, instead of a corner sticking out). I'm sure its obviousy, but the reason being the outward corners a circular dril bit can cut, but inward ones need an arc profile extended beyond where the corner of the other piece will fit into. The drill bit i am using is 6mm, so 6mm diamters arcs is what i'm working with.
I have managed to put such an arc at every vertices of each cut piece. The problem being some stick outward isntead of cutting into the piece. So each one needs to be orieneted correctly. Ideally they would also only draw into inward corners, but I can always delete them out. I think maybe I am missing a more logical mathematical way of defining?
For these geometries it is not very important which side the half circle arc in on in the inward corners, but I also have some geometries that I will have to control where the circles face according to the rest of the cut piece.
The cutouts in the middle of the pieces that are curves do not need such corners obviously.
The picture is an example drawn
I hope this isn't too specific and long. in general though automating fabrication, and controling pracitcal math and orientation problems like this is itnersting to me!
THANKS…
perienced with grasshopper, but so far I've managed to combine the following:
Giulio Piacentino's "Catenary arch from height" script
Pirouz Nourian's "Mobius" script (Obtained from a friend)
End Result:
Here's where I'm stuck: I want the mobius twist to revolve around the midpoint of the arch, but the script uses the input values to determine the endpoints, resulting in a weird sinuous shape when viewed from above. Also, the secondary end points (generated by the mobius script, determining the width of the surface) are generated by default along the z axis, resulting in an arch that only touches the "ground" at two points. I attempted to work around this issue by trying to force the zHeight parameter to correspond with the y axis (thus rotating the arch 90 degrees so it would lay "flat"), but the script interprets the third point as a value and not as an actual point to bisect. I thought this might be an issue with the C# component that I obtained from Giulio Piacentino's script, so I attempted to tinker around with the source code. Unfortunately, I'm not fluent in C# so I only managed to mess everything up (I've since recovered the code from the cache). Anybody got some ideas? -BC …
next level.
This Parametric Design course will provide the participants with the necessary knowledge and ability to use Grasshopper, a free visual programming plugin in Rhinoceros; you will be guided through a series of hands-on exercises that highlight NURBS modeling and its concepts. We will introduce Grasshopper as a graphical algorithm editor tightly integrated with Rhino’s 3D modeling tools. You will also learn how Rhino is used to render models for visualization, translate 3D models for prototyping, and export 3D models into 2D CAD or graphics programs.
English is the course main language.
Location: Düsseldorf city center
Registration and buying Tickets
www.digitalparametrics.eventbrite.de
Course Calendar:
4 Days 6 hours each
Total duration 24h
2 weekends
Date:
Sat. 17 - Sun. 18 June
Sat. 24 - Sun. 25 June
10:00 - 17:00
Getting Started in Rhino. 2 days (17 - 18 June)
Getting Started in Grasshopper. 2 days (24 - 25 June)
-----------------------------------------------------------------------
Participants will be given a certificate of participation at the end of the course.
-----------------------------------------------------------------------
Course fees:
Professionals: 600€ (excl. MwSt.) Students: 500€ (excl. MwSt.) Students need to provide: Copy of current student ID or proof of student enrollment at University/School.
Group discounts:
Group of 3 professionals: 3x500 = 1500€ (excl. MwSt.)
Group of 3 Students: 3x400 = 1200€ (excl. MwSt.)
Participants are kindly asked to bring their own laptops and have pre-installed Rhino + Grasshopper.
Useful Resources:
Rhinoceros Installation (90 days full version trial available): http://www.rhino3d.com/download
Rhinoceros for Mac (includes Grasshopper) http://www.rhino3d.com/download/rhino-for-mac/5/wip
Grasshopper Free Installation: http://www.grasshopper3d.com/page/download-1
Grasshopper Free Plugins: http://www.food4rhino.com/app/lunchbox http://www.giuliopiacentino.com/weaverbird
Main Tutor:
Rihan
M.A. Dipl.Ing. Architect
Architect at RKW Architektur + Düsseldorf
For any questions about the course, please email: info@immersive-studio.com…
ll geometry.
The difference with programs like Inventor is that they are made for production, regardless of the fabrication method. I won't go into detail about that, and instead focus on the modeling process.
In this little model, the starting point actually is a bit obvious, the foundation.
The only contents in the 3dm file are 27 lines. These indicate the location of each footing, and the direction of the tilt of each column. Everything else is defined in GH with the use of numbers as input parameters.
Needless to say, instead of those lines you could obviously generate lines and control the number of columns and panels, hence establish their layout, with any algorithmic or non-algorithmic criteria you please. That marks a major difference between GH and Inventor.
You can generate geometry with Inventor via scripting/customization (beyond iLogic), with transient graphics for visual feedback similar to GH's red-default previews. However Inventor's modeling functions are not set to input and output data trees. I won't go into detail on that, but suffice to say that the data tree associativity of GH was for me the first major difference I noticed. I've used other apps with node diagram interfaces like digital fusion for non-linear video editing since the late 90's, so the canvas did not call my attention when I first started using GH.
Anyways, here's a screen capture of the foundational lines:
In the first group of components, the centerlines of the rear columns are modeled:
And the locations in elevation for connection points are set. Those elevations were just numbers I copied from Excel, but you can obviously control that any way you please. I was just trying to model this quickly.
The same was done for the rear columns:
The above, believe it or not, took me the first 5 hours to get.
Here's a screen capture of what the model and definition looked like after 4 hours, not much:
If you're interested, next post I can get into the sketching part you mentioned, which is a bit cumbersome with GH, but not really.
I wouldn't say that using GH to do this little model was cumbersome, it just needed some thinking at the beginning. You do similar initial thinking when working with a feature-based modeler.…
Added by Santiago Diaz at 12:44am on February 24, 2011