ysim.ning.com/
When you run the simualtion you will notice on the batch terminal that Daysim is also being called, so you may want to consider how Daysim uses Radiance files & data.
Regarding your current problem, I think you stumbled onto something weird and interesting.
Interior and exterior readings appear to differ by 40 in the best case scenarios. Even setting the transmittance to 1 yields similar results. I tried changing from cummulative sky to climate sky and got similar values. Changing the test points did nothing either.
I think, (yet I'm too lazy to prove this) that the difference in values stems from diffuse radiation over the sky dome.
If you delete everything except the glass you'll notice that interior values are like 80-90% of the exterior values (this seems like the expected behaviour with a transmittance of 1). So, if we consider that a vertical window, part of an opaque box, is receiving radiation from 25% of a sphere, as you start to inset the interior test points the radiation they receive will be a fraction of the 25%.
Let me try to explain this better...The exterior surface receives radiation from a section of a sphere calculated by 180degrees on the xy plane (let’s call this angle theta) and by 90degrees (let’s call this angle phi) in azimuthal elevation. If you integrate this over spherical coordinates (theta from 0 to pi; phi from 0 to pi/2) you will find that it comes to a quarter of a sphere. By comparison, the interior surface will not integrate theta from 0 to 180degrees,nor phi from 0 to 90degrees, instead it will be the subtended angle from the exterior surface as a function of their separation; the farther in you go the smaller the view of the outside.
If my hypothesis is correct there shouldn't be that much difference since the separation is only 10cms...the subtended angle would be like 170 instead of 180 for theta and 85 instead of 90 for phi...overall if you integrate both spherical areas there should only by a difference of 10%.
In conclusion, I believe the unexpected behaviour stems from the previous subtended angle thing. If direct radiation was the only factor the difference would be the aforementioned 10%, which suggests that an additional source of energy is also affected by this. Perhaps indirect and diffuse radiation from other areas of the sky dome.
I’m definitely intrigued on why this is happening. Please post if you figure it out.
Regards,
Mauricio
…
TB of RAM. I think I'm going to start a GoFundMe campaign to buy one for myself :)
2- The server's cost is about $13 an hour. I get free access to supercomputer through my university and xsede.org because I earned an NSF Honorable mention last March, however, the supercomputers available through both resources are a little complicated for me to use, as opposed to the one available from amazon that has Microsoft server 2012 already installed.
3- I wanted to run 400 annual glare simulations for 400 different views.
4- I tried a to perform annual glare simulation for one view on my Dell XPS that has Intel Core i7-6700HQ processor and 16GB of system memory. The simulation took 2 hours to complete. Radiance parameter ab was set to 6.
5- I wanted to obtain the batch file for each view so I can run them on the server. So I used the fly component to run all 400 simulations and closed the cmd windows, that wasn't bad ( for me at least) because I asked my son to this job for me, he was just glad to help me :)
6- I created one batch file using this cmd command:
dir /s /b *.bat > runall.bat
This created a file with the path to each .bat file. I edited this file in Notepad++ to include the word "start" at the beginning of each line. This was done using the "find and replace" dialogue box.
7- I split my newly created batch file into 3 batch files, each one has about 130 file names and " start" before the file names.
8- installed radiance on my server
9- Ran the first batch file on the server, this started 130 cmd windows performing my simulations, CPU usage was anywhere between 90% to 100% and about 105 GB of RAMs were used.
10. It took about 5 hours to complete all 130 simulations, I expected to run all in 2 hours but can't complain because this would've taken about 260 hours to run on my laptop. After the simulations done I ran the second and then the third batch files ( total of about 15 hours).
11. I got 400 valid dgb files. Couldn't be happier!
…
he time to work with it.
the project is about facade strips which turns along height. the top angle is
parallel to the facade and the bottom is max. 90 degrees twisted, but the strips
should turn diffrently to achieve more dinamic look.
first i have tried to achieve this by calculating distance between the rotation angle from points of the grid and a single point.
then i have tried to ad some more effecting points and used the distance to the divided surface (the circles are just to control the area of effection):
i manually lofted it.
the result is a bit annoying becouse the points that effect the angle are always visible:
i have triend to solve this by drawing a line and divided it to recieve points along the bottom of the geometry. the result is not working properly:
Anyway,
there must be a better/smoother way to achieve this. i would like to effect the twist of the surfaces by distance to a spline, but im just lost. can you help me please?
the problems im encountering:
0- distance spline to grid to effect the angle
1- list of x/y coordinates and angle of rotation for each point of the grid
2- export points to excel
3- lofting lines in one direction only (x1, x2, x3...)
4- reduce the list data to 2 decimal (0,00)
5- maybe angle from radian to degrees
thx…
assume we want to format two numbers, one integer and a floating point value. The integer represents an index and it should appear inside square brackets, then we want the floating point number rounded to a maximum of 4 decimal places (but always using at least one decimal place, even if it's zero), and then, in parentheses a scientific notation representation using 8 decimal digits of the number.
So, assuming the index is 16 and the value is 47.280006208, what we are after is:
[16] 47.28 (4.72800062E+001)
To make this work, we need a formatting pattern that looks like:
[{0}] {1:0.0###} ({1:E8})
The square brackets, spaces and parenthesis are just part of the output, they have no meaning whilst formatting. Everything inside the curly brackets though will be replaced with a specific formatting of one of the values.
When using the Format component as shown above, the formatting pattern is just text data. The component knows that it is supposed to use the Format() function using the pattern text and whatever additional data is provided.
When you invoke the Format() method in an expression, you do need to make sure that the pattern is actually text:
So here the pattern needs to be encased in double quotes, otherwise it will be treated as code, rather than text.
You cannot use the formatting method in the internal expression of a number parameter, because this method returns text, whereas the number parameter is only capable of storing numbers. Any expression that you put into a number parameter had better return numbers as a result.…
ther math and logic. i can usually conceptualise what i want to do and cobble some semi working thing together but don't know which components to use and how to patch it. so i'm super happy to have someone who knows what he's doing to find this interesting.
and i'm glad you mention the fanned frets again, there is one input parameter that's still missing for the multiscale frets to be fully parametric, it's the angle of the nut or which fret should be straight. it depends a bit on personal preferences and playing posture what is more comfortable. so being able to adjust this easily would be cool. again i have no idea how the maths for that work or if you can just rotate each fret the same amount around it's middle point. The input either as fret number (for the straight fret) or as a simple slider from bridge to nut should do as input setting.
Here are the two extremes and the middle ground:
i've been thinkin today while analysing your patches and cleaning up my mess what exactly the monster should do.
Here are the input parameters needed, i think it's the complete list
scale length low E string
scale length high e string
fret angle/straight fret
string width at nut
string width at bridge
number of frets
fretboard overhang at nut (distance from string to fretboard bounds)
fretboard overhang at last fret
string gauges
string tensions
fretboard radius at nut (for compound radius fretboard radius at bridge is calculated with the stewmac formula)
fretwire crown width
fretwire crown height
action height at nut (distance between bottom of string and fretwire crown top)
action height at last fret
pickup 1 neck position
pickup 2 middle position
pickup 3 bridge position
nut width
the pickup positions should be used to draw circles for the magnet poles on each string so they are perfectly aligned and can be used for the pickup flatwork construction. ideally they would need a rotation control aligning the center line of the pickup so it's somewher between the last fret angle and bridge angle. personally i do this visually depending on the design i'm looking for, some people have huge theories on pickup positioning but personally i don't believe in it.
that should result in everything needed to quickly generate all the necessary construction curves or geometry for nut/fingerboard/frets/pickups. this is the core of what makes a guitar work, the more precise this dynamic system is the better the guitar plays and sounds.
i posted another thread trying to understand how i could use datasets form spreadsheets,databse, csv to organize the input parameters. What would make sense for the strings for example is hook into a spreadsheet with the different string sets, i attached one for the d'Addario NYXL string line which basically covers all combos that make sense.
The string tension is an interesting one, and implmenting it would sure be overkill albeit super interesting to try. it should be possible to extrapolate from the scale length of each string what the tension for a given string gauge of that string would be so that you could say 'i want a fully balanced set' or 'heavy top light bottom) and it would calculate which SKU from d'addario would best match the required tension. All the strings listed in the spreadsheet are available as single strings to buy.
i'm trying to reorganize everything which helps me understand it. i just discovered the 'hidden wires' feature which is great since once i understood what a certain block does or have finished one of my own, i can get the wires out of the way to carry on undistracted. a bit risky to hide so many wires but it makes it so much easier not to get completely lost :-)
btw, the 'fanned fret' term is trademarked, some guy tried to patent it in the 80's which is a bit silly since it has been done for centuries. there is a level of sophistication above this as well, check out http://www.truetemperament.com/ and that really is something else. it really is astounding how superior the tuning is on those wigglefrets, the problem is that it's rather awkward for string bending and also you can't easily recrown or level the frets when they are used. …
e matching with a dedicated component which creates combinations of items. You can find the [Cross Reference] component in the Sets.List panel.
When Grasshopper iterates over lists of items, it will match the first item in list A with the first item in list B. Then the second item in list A with the second item in list B and so on and so forth. Sometimes however you want all items in list A to combine with all items in list B, the [Cross Reference] component allows you to do this.
Here we have two input lists {A,B,C} and {X,Y,Z}. Normally Grasshopper would iterate over these lists and only consider the combinations {A,X}, {B,Y} and {C,Z}. There are however six more combinations that are not typically considered, to wit: {A,Y}, {A,Z}, {B,X}, {B,Z}, {C,X} and {C,Y}. As you can see the output of the [Cross Reference] component is such that all nine permutations are indeed present.
We can denote the behaviour of data cross referencing using a table. The rows represent the first list of items, the columns the second. If we create all possible permutations, the table will have a dot in every single cell, as every cell represents a unique combination of two source list indices:
Sometimes however you don't want all possible permutations. Sometimes you wish to exclude certain areas because they would result in meaningless or invalid computations. A common exclusion principle is to ignore all cells that are on the diagonal of the table. The image above shows a 'holistic' matching, whereas the 'diagonal' option (available from the [Cross Reference] component menu) has gaps for {0,0}, {1,1}, {2,2} and {3,3}:
If we apply this to our {A,B,C}, {X,Y,Z} example, we should expect to not see the combinations for {A,X}, {B,Y} and {C,Z}:
The rule that is applied to 'diagonal' matching is: "Skip all permutations where all items have the same list index". 'Coincident' matching is the same as 'diagonal' matching in the case of two input lists which is why I won't show an example of it here (since we are only dealing with 2-list examples), but the rule is subtly different: "Skip all permutations where any two items have the same list index".
The four remaining matching algorithms are all variations on the same theme. 'Lower triangle' matching applies the rule: "Skip all permutations where the index of an item is less than the index of the item in the next list", resulting in an empty triangle but with items on the diagonal.
'Lower triangle (strict)' matching goes one step further and also eliminates the items on the diagonal:
'Upper Triangle' and 'Upper Triangle (strict)' are mirror images of the previous two algorithms, resulting in empty triangles on the other side of the diagonal line:
…
ake a modest notice about the two new Ladybug components, one of which creates a 3d terrain shading mask and another one which visualizes and exports horizon angles. A terrain shading mask is essentially a diagram which maps the silhouette of the surrounding terrain (hills, valleys, mountains, tree tops...) around the chosen location, and account for the shading losses from the terrain. It can be used as a context_ input in mountainous or higher latitude regions for any kind of sun related analysis: sunlight hours analysis, solar radiation analysis, view analysis, photovoltaics/solar water heating sunpath shading...
My home town is an example of the shading caused by the terrain. Here is how it looks from the tallest building in the town:
And the created terrain shading mask:
A mask for any land location up to 60 degrees North can be created:
There will also be a support for a few major cities above this limit.
Both Terrain shading mask and Horizon angles components can be downloaded from here. An example .gh file can be found in here.
Component will prompt the user to download and copy certain files in order to be able to run.
It was created with assistance from Dr. Bojan Savric. Support on various issues was further given by: Dr. Graham Dawson, Dr. Alec Bennett, Dr. Ulrich Deuschle, Andrew T. Young, LiMinlu, Jonathan de Ferranti, Michal Migurski, Christopher Crosby, Even Rouault, Tamas Szekeres, Izabela Spasic, Mostapha Sadeghipour Roudsari, Dragan Milenkovic, Chen Weiqing, Menno Deij-van Rijswijk and gis.stackexchange.com community.
I hope somebody might find the components useful.…
te some cut sheets, but not to optmize material, rather define some cut lines. Everything that I am cutting is made of planar wood elements, but there are very specific geometries (mostly straight lines) and I have to put tolerances and radiasas at the corners in order to cut on the cnc mill. Spending time to figure out how to automate is necessary, but I am stuck!
One thing the definition is doing is taking my brep modeled components in rhino and makking them into 2d close curves and laying them side by side. It works...not ideal as its not layed out in a sheet, but that is not the most important part.
Another particular problem is that you will see some notches in the curves, which other pieces will slip into, so different slots need different specific offsets (making them larger) as a toelrance to allow for material play. This I don't even know how to set up so maybe it will just have to wait.
THE MAIN QUESTION, and super important would be, LIFESAVER:
At all 'inward' corners...which I think will always mean concave corners (most are 90 degrees, but are within to sides, instead of a corner sticking out). I'm sure its obviousy, but the reason being the outward corners a circular dril bit can cut, but inward ones need an arc profile extended beyond where the corner of the other piece will fit into. The drill bit i am using is 6mm, so 6mm diamters arcs is what i'm working with.
I have managed to put such an arc at every vertices of each cut piece. The problem being some stick outward isntead of cutting into the piece. So each one needs to be orieneted correctly. Ideally they would also only draw into inward corners, but I can always delete them out. I think maybe I am missing a more logical mathematical way of defining?
For these geometries it is not very important which side the half circle arc in on in the inward corners, but I also have some geometries that I will have to control where the circles face according to the rest of the cut piece.
The cutouts in the middle of the pieces that are curves do not need such corners obviously.
The picture is an example drawn
I hope this isn't too specific and long. in general though automating fabrication, and controling pracitcal math and orientation problems like this is itnersting to me!
THANKS…
onsidered period.
Even if the end of July for the mediterranean climate is not the best period to perform an adaptive comfort analysis (it's just a pretest to define a LB model) I want to refine the Adaptive comfort Chart (AC) by changing the external air temperature data imported from the .epw file with that of monitored data as reported here below:
Where the monitored ext air temperature are in this form (green panel below):
I have used the comfortPar component to set the following parameters:
Adaptive chart as defined by EN 15251
90% of occupants comfortable
the prevailing outdoor temperature from a weighted running mean of the last week
fully conditioned space (even if it is not properly in line with AC as already discussed)
The question is this: the AC component could correctly apply the code below if there is only a list of external temperature data for a restricted period (without indication about the limits of this period) and not for an entire year?
else: #Calculate a running mean temperature. alpha = 0.8 divisor = 1 + alpha + math.pow(alpha,2) + math.pow(alpha,3) + math.pow(alpha,4) + math.pow(alpha,5) dividend = (sum(_prevailingOutdoorTemp[-24:-1] + [_prevailingOutdoorTemp[-1]])/24) + (alpha*(sum(_prevailingOutdoorTemp[-48:-24])/24)) + (math.pow(alpha,2)*(sum(_prevailingOutdoorTemp[-72:-48])/24)) + (math.pow(alpha,3)*(sum(_prevailingOutdoorTemp[-96:-72])/24)) + (math.pow(alpha,4)*(sum(_prevailingOutdoorTemp[-120:-96])/24)) + (math.pow(alpha,5)*(sum(_prevailingOutdoorTemp[-144:-120])/24)) startingTemp = dividend/divisor if startingTemp < 10: coldTimes.append(0) outdoorTemp = _prevailingOutdoorTemp[7:] startingMean = sum(outdoorTemp[:24])/24 dailyRunMeans = [startingTemp] dailyMeans = [startingMean] prevailTemp.extend(duplicateData([startingTemp], 24)) startHour = 24
…
see in my bottom post image there is only one isocurve showing in U and V.
In Grasshopper there's no surface rebuild? Well, the same old Grasshopper Patch command will let you specify spans I guess, to make a surface from a planar curve, but it won't work for things with holes since they will just fill in!
You can recreate a surface painfully by untrimming, adding many UV points, rebuilding from those points, then retrimming with the original surface info, but the retrimming simply fails.
If you make a planar surface from a curve in Rhino, you end up with utterly no point editability:
No wonder my CreatePatch tests were a failure. The starting surface could not be distorted except in the extreme case of moving four corner points!
I have no idea how to successfully rebuild a surface akin to the Rhino rebuild command. It's great to be able to prototype in Grasshopper, but with Python I can rebuild easily ( http://4.rhino3d.com/5/rhinocommon/?topic=html/M_Rhino_Geometry_Surface_Rebuild.htm ;), so I guess I should start a collection, like peter, of little script components for prototyping with.…
Added by Nik Willmore at 6:18am on February 26, 2016