ing ways to leverage simulation results from ladybug and inform design of building envelops with benefits that can be modeled. Given 20 percent of the cost of a project typically goes to the facades, and maybe a half of that goes to the openings, there is a good enough reason to question how to materialize that 10 percent, which can result in 10-30 percent difference in total energy comsumption.
I think ideally radiation analysis, natural ventilation and daylight analysis on floors should all inform opening sizes and placements, as well as the building sections at large. However natural ventilation seems to be the most complicated one because it couples airflow and thermo dynamics. I have a definition setup so that I can batch simulations for radiation analysis and daylight analysis, but natural ventilation is the missing link. So for what I am doing now I will select a handful of design that seem to work the best based on the two available analysis and convert all the geometry into CAD files so that I can run them in an evaluation copy of autodesk simulation CFD. So for now I can do this in 2 stages.
But for the future, given the possibility of actually have that as a part of grasshopper feature, which would be lovely, I want to understand the science behind it and share some links.
(http://www.wbdg.org/resources/naturalventilation.php) In this link the author outlines quite a few general principles and variables to consider for natural ventilated buildings.
For example, how stack effect works.
Qstack = Cd*A*[2gh(Ti-To)/Ti]^1/2, where
Qstack = volume of ventilation rate (m³/s)Cd = 0.65, a discharge coefficient.A = free area of inlet opening (m²), which equals area of outlet opening.g =9.8 (m/s²). the acceleration due to gravityh = vertical distance between inlet and outlet midpoints (m)Ti = average temperature of indoor air (K), note that 27°C = 300 K.To = average temperature of outdoor air (K)
The thing about natural ventilation is that not only the sizes and positioning of openings of the facade facing predominant wind matter, but also the openings on the other side matter. The vertical distance between the inlets and outlets also need to be taken into account. The author suggests that naturally ventilated buildings should be no wider than 45 feet.
and in this pdf presentation it discusses CFD for natural ventilation and illustrates why it is not easy
http://isites.harvard.edu/fs/docs/icb.topic882838.files/L17.6205Airflow-Modeling_Ibarra.pdf
and in this pdf briefly outlines the approach taken by designbuilder
http://isites.harvard.edu/fs/docs/icb.topic472869.files/DesignBuilder%20Simulation%20Training_HSD.pdf
Lastly a wide spectrum of environmental analysis works by e3lab
http://www.e3lab.org/research
http://www.e3lab.org/green-buildings
If I make progress on a way to tie the three analysis together (radiation, daylight and natural ventilation), I wont forget to post it on this thread.
Thanks.…
nergy plus silulation and this is the error text:
Current document units is in MetersConversion to Meters will be applied = 1.000Duplicate surface name! Name is changed to: Pelle_Sopra_DupDuplicate surface name! Name is changed to: Pelle_Nord_Dup[1 of 8] Writing simulation parameters...[2 of 8] No context surfaces...[3 of 8] Writing geometry...[4 of 8] Writing Electric Load Center - Generator specifications ...[5 of 8] Writing materials and constructions...[6 of 8] Writing schedules...[7 of 8] Writing loads and ideal air system...[8 of 8] Writing outputs......... idf file is successfully written to : C:\Users\Personal\Desktop\TESI\x006\THOR001\EnergyPlus\THOR001.idf
Analysis is running!...C:\Users\Personal\Desktop\TESI\x006\THOR001\EnergyPlus\eplusout.csv......
Done! Read below for errors and warnings:
Program Version,EnergyPlus, Version 8.3.0-6d97d074ea, YMD=2016.01.05 20:08,IDD_Version 8.3.0
************* IDF Context for following error/warning message:
************* Note -- lines truncated at 300 characters, if necessary...
************* 160 ScheduleTypeLimits,
************* indicated Name=ANY NUMBER
************* Only last 2 lines before error line shown.....
************* 161 ANY NUMBER, !- name
************* 162 ScheduleTypeLimits, !-
** Severe ** IP: IDF line~162 Invalid Number in Numeric Field#1 (Lower Limit Value), value=SCHEDULETYPELIMITS, in SCHEDULETYPELIMITS=ANY NUMBER
************* IDF Context for following error/warning message:
************* Note -- lines truncated at 300 characters, if necessary...
************* 258 ScheduleTypeLimits,
************* indicated Name=ANY NUMBER
************* Only last 2 lines before error line shown.....
************* 259 ANY NUMBER, !- name
************* 260 ScheduleTypeLimits, !-
** Severe ** IP: IDF line~260 Invalid Number in Numeric Field#1 (Lower Limit Value), value=SCHEDULETYPELIMITS, in SCHEDULETYPELIMITS=ANY NUMBER
** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
** Severe ** IP: Possible incorrect IDD File
** ~~~ ** IDD Version:"IDD_Version 8.3.0"
** ~~~ ** Version in IDF="8.3.0" not the same as expected="8.3"
** ~~~ ** Possible Invalid Numerics or other problems
** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
...Summary of Errors that led to program termination:
..... Reference severe error count=3
..... Last severe error=IP: Possible incorrect IDD File
************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 3 Severe Errors; Elapsed Time=00hr 00min 0.30sec
thanks for any help
Lhor…
os3D + Grasshopper3D + Maya + Advanced Plugins & Demo Toolkits]
// Level
Basic, Intermediate & Advanced
(Previous parametric design knowledge not obligatory - Studio is adaptive to basic & advanced users)
// Agenda
The workshop aims to provide a detailed insight to ‘parametric design’ and embedded logics behind it through a series of design explorations using Rhinoceros & Grasshopper platforms, along with understanding of data-driven design strategies. An insight to Computational Design and its subsets of Parametric Design, Algorithmic Design, Generative Design and Evolutionary Design will be provided through presentations, technical sessions & studio work. Studio work will be focusing on modulation of geometry and iterative form using Parametric Design methods that will lead to explorations of spatial geometries that can be articulated as architectural constructs or abstract artistic interventions. There will be a demonstration of Fluid Form Modelling using Autodesk Maya on Day03.
The 1st batch of workshop in London took place in January 2020 with an exploratory learning output for ~20+ participants that travelled from different parts of the world to be a part of 3-day workshop titled Parametric Modulations. V2.0 is the evolved workshop with new toolkit add-ons for the 2nd batch and demonstrative tools & examples for future use of participants to get a deeper understanding of Computational & Parametric Design.
// Methodology
The 3-day studio / workshop shall focus on inculcating the following aspects as a part of curriculum:
Computational Design Techniques & Parametric Design
Data, Mathematics & Geometry
Geometry Rationalization
Iterative Form Development
Digital simulation of forces
Environmental Analysis (Tool-kits & Example files for future use)
Collaborative Design Exercises to understand application of the learnt tools
Documentation and Presentation
Hands-on Demonstration of Maya (Polygonal Mesh Modelling)
The workshop is suitable for beginners, intermediate as well as advanced users of these tools and very helpful for anyone planning to start their Masters in UK as this 3-day workshop would serve as a bootcamp to kick-start anyone's journey in Computational Design.
…
Introduction to Grasshopper Videos by David Rutten.
Wondering how to get started with Grasshopper? Look no further. Spend an some time with the creator of Grasshopper, David Rutten, to learn the
rested in specializing in the field of Computational design.
The workshop will help understand how Grasshopper facilitates during the design process allowing one to Generate, Automate and Manipulate data.
To Register:
http://goo.gl/forms/gvUTyZihVK
Workshop Structure:
Day 01: 16 August 2018
Introduction to Computational Processes in Architecture
Understanding Grasshopper and its relation to Rhino3D
Working with fields and Grids (Supplementary readings for Architectural theory)
Spatial Concepts using Data
Day 02: 17 August 2018
Understanding Data in Grasshopper - LISTS
Managing Data in Grasshopper (Supplementary reading)
Experimentation on Massing and Architectural Forms
Day 03: 18 August 2018
Understanding Data in Grasshopper – Trees
Surface Logics (Supplementary reading)
Design Exercise and Prototyping
Day 04: 20 August 2018
Architectural Skins
Day 05: 21 August 2018
MasterClass Project
Introduction to various types of Digital Fabrications
Prototyping of works during the Workshops
Basic knowledge of Rhino 5 is required to be able to take this training.
CERTIFICATION: All participants will receive a Workshop certificate from Authorized Rhino Trainer.
3D Printing: Prototyping of works during the Workshops
Workshop Tutor:
Kavitha M, an Architect and Computational Designer, 3D Printing Specialist is also the co-founder of INTO Design Research, will head the Computational Process in Architecture using Grasshopper workshop. Graduated from Stadelschule Architecture class with Masters in Advanced Architecture Design, has been researching on teaching methodologies on digital tools and their influence on Design thinking.…
I thought the easiest way (and really tight deadline now) was c4d mesh deformer because it lets one choose a cage object, so I modeled this "rig", essentially a mesh of 20 carefuly measured points to see how exact the real thing is to the 3d model. My plan is to deform the entire mesh from source (3d model) to target (meaured low resolution mesh = "rig" )
(above two images : C4D test... work with a spheric cage - but not with a mesh I modelled in rhino)
C4D Mesh Deformer doesn't work with the cage geometry like this because I think the cage geometry actually need to be larger and be more like a cage, but of course I can't measure Imaginary cage off this thing :)
So I am asking for a suggestion for any quick tool like mesh deform in c4d, or how one might go about it with grasshopper...
I am attaching the file - for example you can see the magenta colored points and lines show the measured deflection of the structure, from teal-colored points and lines.
The requirement is that the individual surfaces need to export as individual objects in the end.
I am attaching the rhino file here.
https://drive.google.com/open?id=0B8u1qSty0juhVmtCYnEtdFktME0
The exported object files of the individual surfaces need to be within 3mm off from the actual thing for this installation to work.. looking to how surface morph grasshopper component work at the moment.
Best,
Youngjae
Thanks!
Youngjae…
NONE, in SIZING:PARAMETERS". I'm not sure of where to start in troubleshooting this. I've attached the file.
Thank you,
See the errors and warnings below:
{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. [1 of 8] Writing simulation parameters...
3. [2 of 8] Writing context surfaces...
4. [2 of 8] Writing context surfaces...
5. [3 of 8] Writing geometry...
6. [4 of 8] Writing Electric Load Center - Generator specifications ...
7. [5 of 8] Writing materials and constructions...
8. [6 of 8] Writing schedules...
9. [7 of 8] Writing loads and ideal air system...
10. [8 of 8] Writing outputs...
11. ...
... idf file is successfully written to : R:\Green\SuRG\Building_Performance_Analysis\2016_analysis_studies\Energy_Analysis_Comparison\Honeybee_+_Ladybug\tutorial01\EnergyPlus\tutorial01.idf
12.
13. Analysis is running!...
14. ...
...
Done! Read below for errors and warnings:
15.
16. Program Version,EnergyPlus, Version 8.5.0-c87e61b44b, YMD=2016.10.31 11:39,IDD_Version 8.5.0
17.
18. ************* IDF Context for following error/warning message:
19.
20. ************* Note -- lines truncated at 300 characters, if necessary...
21.
22. ************* 24 Sizing:Parameters,
23.
24. ************* Only last 1 lines before error line shown.....
25.
26. ************* 25 None, !- Heating Sizing Factor
27.
28. ** Severe ** IP: IDF line~25 Invalid Number in Numeric Field#1 (Heating Sizing Factor), value=NONE, in SIZING:PARAMETERS
29.
30. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
31.
32. ** ~~~ ** Possible Invalid Numerics or other problems
33.
34. ** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
35.
36. ...Summary of Errors that led to program termination:
37.
38. ..... Reference severe error count=1
39.
40. ..... Last severe error=IP: IDF line~
, value=NONE, in SIZING:PARAMETERS
41.
42. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
43.
44. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
45.
46. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
47.
48. ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
49.
50. ************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 9.34sec
51.…
giornata inaugurale sarà dedicata alla free-lecture introduttiva finalizzata alla realizzazione di un modello d'architettura complesso attraverso l'utilizzo di comandi e tecniche avanzate di rappresentazione con Grasshopper (plug-in parametrica di Rhinoceros) e 3dsMax. Sarà illustrato inoltre il potenziale di V-ray per 3dsMax realizzando un rendering concettuale. Durante il mini-corso dell' openDAY verranno mostrate le caratteristiche e le potenzialità degli strumenti per far luce sui nuovi valori assunti dalla modellazione 3D. La modellazione 3D sta interessando un pubblico sempre più vasto inserendosi in una nuova fase di ampia disponibilità per conoscenze, software, hardware di prototipazione e modelli. Pur mantenendo tutti i suoi valori già noti la questione si è talmente ampliata fino ad interessare norme giuridiche (diritti sui modelli ,concorrenza con offerte di servizi apparentemente simili, informazioni deformate e onfusione nei media) Makers University[http://www.makersuniversity.com], in collaborazione con parametricart, vi propone un punto di vista ampio e sintetico su queste tematiche.
Al termine della free-lecture, sarà illustrata l'offerta formativa [CLICCA QUI] di parametricart riferita ai corsi che si terranno nei mesi di Gennaio e Febbraio 2013 inseriti all'interno della più ampia programmazione della Makers University. SONO PREVISTE TARIFFE PROMOZIONALI PER COLORO CHE SI ISCRIVERANNO AI CORSI durante l'OpenDAY.
La lezione e la presentazione si terranno nel nuovo spazio co-working il PEDONE.
PROGRAMMAZIONE
- I temi della Makers University [Leo Sorge];
- Modellazione della parametricTower (concept di architettura complessa) utilizzando Grasshopper, applicativo per la modellazione parametrica [VIDEO] [Michele Calvano];
- Modellazione di una copertura reticolare 3D a completamento della parametricTower con 3dsMax utilizzando tecniche di modellazione mesh complesse [Wissam Wahbeh];
- Rendering con V-ray per 3dsMax illustrando la nuova interfaccia nodale [Wissam Wahbeh].
- Question Time per chiarimenti sugli argomenti illustrati.
COME
L'openDAY sarà aperto a tutti gli interessati,completamente gratuito e sarà replicato in tre sessioni di uguali contenuti organizzate nei seguenti orari:
Sessione [1] 11,30 - 13,30
Sessione [2] 15,30 - 17,30
Sessione [3] 17,30 - 19,30
Per necessità di organizzazione è importante la prenotazione all'evento utilizzando il form in fondo alla pagina specificando nella stringa apposita, il nome dell'evento e la sessione (es. open day sessione 1) oltre agli altri dati richiesti.…
la corretta comprensione del software che di livello specialistico per un confronto diretto con alcuni aspetti fondamentali dell’ architettura e del design.
Attraverso l'utilizzo di Grasshopper rivoluzionaria plug-in di Rhinoceros, si insegneranno nuove tecniche di modellazione parametrica.
Grasshopper, permette di esprimere al massimo le qualità e le potenzialità della modellazione Nurbs abbandonando in parte l'interfaccia classica di Rhinoceros. Quest'ultimo infatti viene sostituito da un menù a tendine dove vengono collezionati nodi utili alla composizione di algoritmi risolutivi.
La plug-in Grasshopper, dimostra come il linguaggio del computer stia diventando un reale strumento progettuale.
Il corso si svolgerà nei seguenti giorni: Sabato 26 Ottobre dalle ore 10.00 alle ore 19.00 Domenica 27 Ottobre dalle ore 10.00 alle ore 19.00 Scadenza preiscrizione per Grasshopper: 23/10
Contenuti
Nella prima parte del corso attraverso degli esercizi base si insegneranno i metodi di esplicitazione degli algoritmi generativi. In queste ore di lezione si illustreranno, attraverso fasi operative, i seguenti argomenti:
Suddivisione degli algoritmi in parametri e componenti;
Tipologie di dati comptiili con Grasshopper e loro combinazione creando definizioni minime;
Funzioni matematiche e logiche;
Data flow, liste e filtri di esclusione;
Costruzione di curve e superfici e loro trasformazione;
Nella seconda parte del corso lo strumento viene specializzato affrontando editing e trasformazioni complesse sulle superfici:
Elaborazione delle superfici di suddivisione;
Tassellazione spaziale di superfici a doppia curvatura;
Gestione di parametri variabili per la progettazione di definizioni finalizzate al controllo del movimento;
Ideazione di algoritmi per il passaggio dal modello digitale al modello reale attraverso la tecnica dello sliceing;
Alla fine del corso, verrà rilasciato l’attestato di partecipazione ad un corso di Rhinoceros qualificato certificato dalla casa sviluppatrice McNeel, valido anche per la richiesta di crediti formativi universitari.
Tutor del corso
Il corso sarà tenuto da un docente qualificato, esperto in disegno e rappresentazione dell' architettura e del design:
Michele Calvano| _architetto, dottore di ricerca in rappresentazione architettonica specializzato nella modellazione matematica (Nurbs) e modellazione parametrica.
Docente ART (Autorized Rhino Trainer)
Info
Responsabile didattico e docente del corso: arch. Michele Calvano cell: 340 3476330
Info mail: parametricart@gmail.com
…
azione tramite interfaccia grafica 6 ore
Interfaccia Grasshopper
Parametri e Componenti
Operazione di Logica e Matematica
Vettori
Case study: concetto base di attrattore
Gestione data matching
Primi approcci alla modellazione parametrica – 4 ore
Trasformazioni di base (sposta ruota scala orienta)
Strumenti di Morphing
Utilizzo di Sweep e Loft e di altri strumenti di creazione superfici già noti da Rhinoceros
Esercitazione pratica: creazione del modello concettuale della Serpentine Gallery - B.I.G.
Focus sulla gestione dei dati - 4 ore
Creazione e gestione delle liste
Studio del data tree
Esercitazione pratica: creazione di un soffitto cassettonato
Creazione di geometrie tramite mesh – 6 ore
Utilizzo degli algoritmi di Delaunay
Utilizzo del Facet Dome
Utilizzo del Substrate
Utilizzo degli algoritmi di Voronoi
Esercitazione pratica: creazione di un gazebo attraverso l’uso di pattern
Creazione di ‘paneling’ di superfici curve – 6 ore
Discretizzazione di una superficie a doppia curvatura tramite pannelli piani
Strumenti analisi superfici
Visualizzazione superfici tramite falsi colori
Esercitazione pratica: creazione di una facciata interattiva
Digital Fabrication e messa in tavola – 6 ore
Interoperabilità tra Grasshopper e altri applicativi
Creazione di Truss parametrica
Gestione dell’abaco dei pezzi
Esercitazione pratica: la Facciata dello Stadio Friuli di Udine - Ipotesi di costruzione e gestione tramita fabbricazione digitale
Requisiti di accesso
Conoscenza delle tematiche CAD di base e dei comandi principali e interfaccia Rhinoceros 5.
Certificazioni
Alla fine del corso verranno rilasciate le certificazioni ufficiali da ART (Authorized Rhinoceros Trainer)
Numero partecipanti
Il corso parte al raggiungimento di un minimo di 4 persone ad un massimo di 8. Ogni partecipante dovrà essere munito di proprio computer con Rhinoceros.
Costo del corso
Il costo del corso è di 600 € + IVA
Sconto di 50,00 € per i giovani che hanno meno di 26 anni.
Ulteriore sconto di 50,00 € Early Bird per tutti coloro che si iscriveranno entro il 5 Settembre 2016
Nel prezzo è compresa l’iscrizione al FabLab Toscana – maggiori informazioni qui
FabLab Toscana
Il FabLab Toscana presenta un insieme di per i propri associati: sarà possibile l’accesso ai laboratori del FabLab (durante i normali orari di apertura), partecipare ai workshops gratuitamente o a prezzi calmierati, l’utilizzo della macchine (seguendo il regolamento interno), …