ur setup. Can you say what sensor you are using? Are you using an Arduino to write this ascii information to the serial port? If so, there may be some formatting code for the string that you'll need to do to get the Read component to function properly. I see that you were able to open the port and Start reading... so my first thought is that the data is formatted correctly....
All of the read components look for a specific character (in this case two characters) to indicate when it has reached the end of the line being read and should spit out the data. In this case, Firefly uses the Carriage Return (\r) and Line Feed (\n) to know when it has reached the end of the line. In arduino, these are automatically added to any line if you use the Serial.println("blah, blah, blah"); command. Notice, this is different from the Serial.print("nothing to see here"); command. This doesn't mean that you can't still use the regular print command... it's just you need to use the println command to indicate when you've reached the end of the line. Let's take a look at a simple example.
void setup() { Serial.begin(9600);}void loop() { int sensorValue = analogRead(A0); Serial.print("The value of the sensor is: "); Serial.println(sensorValue);
delay(20); // important to wait some small time so you aren't sending just a ton of info over to GH which will cause it to crash :(
}
The first print statement prints a string to the serial port... and the next one adds the current sensor value... and THEN adds the carriage return and line feed to start a new line. The nice thing about using these together is that you can concatenate any type of data you want. If you were to upload this sketch, you should see a sentence being printed to the serial port that says "The value of the sensor is: 512". I made up the number, but you get the idea. Notice, I also had to include a delay function. You don't always need this (there are other ways to go about this) but the important thing to note is that the loop cycle on the Arduino can run really fast. I mean... really fast. So, you wont want to send so much data over to GH, because this could flood the string buffer in the Read component and cause it to crash (eventually). It's a good idea to add some small time interval just to slow it down a bit. I should say that I've optimized the refresh rate in the next release so it's significantly faster... so hopefully this wont be as big of a problem... but hopefully that helps some.
Now... Why are you writing data to a sensor? Sensors by default are considered inputs... so I'm quite confused as to why you would want to send data back (if you are... then you need some way to handle the string data being sent from GH... this is the whole reason we built the Firefly firmata... it sets up the two-way protocol so you don't have to deal with all of that mess... If you're going to read and write, you're better off just uploading the firmata and using the Uno Read and Write components). Also, I'm not very familiar with the Hyperterm or Advanced Serial Port Terminal... but I will say that could get COM conflicts if you're trying to open the port with different tools. Anyway, I hope some of this helps you get up and running.
Cheers,
Andy
…
DP ($$$ aside), GC, and Grasshopper. Arthur’s original question is very important
and the exact question (and hopefully answer) I was hoping to find on a
forum.
“How to take intelligent 3D parametric generative design models (scripting, etc.) into 2D documents?" Or, deliver the 3D design for evaluation, bid, construction, etc.
I am intrigued by Jon’s comments in the same thread and would like to know how I can learn more about the process (and
pitfalls) of turning over a 3D digital generative models to a contractor/fabricator.
Are there any industry guidelines established I could use as a reference to guide our firm through this type of uncharted territory?
Arthur’s question is very reminiscent of 10 years ago when I was frustrated with the amount of time spent on the development of a 3D model design (physical and/or virtual) only to have to wipe the table clean and start the process all over again in 2D in order to document the project for delivery. From this I jumped head first into BIM and Revit, vowing never to go back to unintelligent 2D line work. I am now working on Bentley software (v8i: Microstation and Bentley Architecture) with the access and desire to venture into Generative Components. I am very intrigued by Rhino/Grasshopper primarily with the apparent ease of use and available resources assisting in the learning process – something not really available with Bentley.
In hindsight, as I am doing my software research I think the current use of Revit and BA (Bentley Architecture) are more of a “bridge”
between the past (decades of digital 2D work, i.e. AutoCAD) and where hopefully
we all will be someday in the near future (100% 3D modeling, i.e. Digital
Project??). Without having the experience
it would appear that DP/CATIA (PLM software) are closer to this than any other
type of software. As complicated as the
industry standards are for the automobile and airline industry, I feel we
(architectural industry and others) are heading in a similar direction with
total understanding (PLM/ Evidence Based Design) of a design (a whole other topic). If anything I think the market will begin to
demand it sooner or later.
Gehry (DP) article NY Times:
http://www.nytimes.com/2009/02/11/business/11gehry.html
I know these type of broad discussions (software vs. software) can be blown out of proportion on forums, but I am would like to read
the pulse of those who are already in the trenches (using Grasshopper, CATIA, Digital Project, Generative Components, others??) and hear your thoughts. Just as valuable would be other threads,
industry articles/reviews of 3D parametric generative design software.
Thanks,
Boyd…
oftware connections built from the initial seed of the project. As always you can download the new release from Food4Rhino. Make sure to remove the older version of Ladybug and Honeybee and update your scripts.
This release is also special since today it is just about 3 years (3 years and 2 weeks) from the first release of Ladybug. As with any release, there have been a number of bug fixes and improvements but we also have some major news this time. In no specific order and to ensure that the biggest developments do not get lost in the extensive list of updates, here are the major ones:
Mostapha is re-writing Ladybug!
Ladybug for DynamoBIM is finally available.
Chris made bakeIt really useful by incorporating an export pathway to PDFs and vector-based programs.
Honeybee is now connected to THERM and the LBNL suite thanks to Chris Mackey.
Sarith has addressed a much-desired wish for Honeybee (Hi Theodore!) by adding components to model electric lighting with Radiance.
Djordje is on his way to making renewable energy deeply integrated with Ladybug by releasing components for modeling solar hot water.
There is new bug. Check the bottom of the post for Dragonfly!
Last but definitely not least (in case you’re not still convinced that this release is a major one) Miguel has started a new project that brings some of Ladybug’s features directly to Rhino. We mean Rhino Rhino - A Rhino plugin! Say hi to Icarus! #surprise
Before we forget! Ladybug and Honeybee now have official stickers. Yes! We know about T-Shirts and mugs and they will be next. For now, you can deck-out your laptops and powerhouse simulation machines with the symbology of our collaborative software ecosystem.
Now go grab a cup of tea/coffee and read the details below:
Rewriting Ladybug!
Perhaps the most far-reaching development of the last 4 months is an effort on the part of Mostapha to initiate a well structured, well documented, flexible, and extendable version of the Ladybug libraries. While such code is something that few community members will interact with directly, a well-documented library is critical for maintaining the project, adding new features, and for porting Ladybug to other software platforms.
The new Ladybug libraries are still under development across a number of new repositories and they separate a ladybug-core, which includes epw parsing and all non-geometric functions, from interface-specific geometry libraries. This allows us to easily extend Ladybug to other platforms with a different geometry library for each platform (ie. ladybug-grasshopper, ladybug-dynamo, ladybug-web, etc) all of which are developed on top of the ladybug-core.
Without getting too technical, here is an example of a useful outcome of this development. If you want to know the number of hours that relative humidity is more than 90% for a given epw, all that you have to code (in any python interface) is the following:
import ladybug as lb
_epwFile = r"C:\EnergyPlusV7-2-0\WeatherData\USA_CO_Golden-NREL.724666_TMY3.epw"
epwfile = lb.epw.EPW(_epwFile)
filteredData = epwfile.relativeHumidity.filterByConditionalStatement('x>90')
print "Number of hours with Humidity more than 90 is %d "%len(filteredData.timeStamps)
Compare that to the 500 + lines that you would have had to write previously for this operation, which were usually tied to a single interface! Now let’s see what will happen if you want to use the geometry-specific libraries. Let’s draw a sunpath in Grasshopper:
import ladybuggrasshopper.epw as epw
import ladybuggrasshopper.sunpath as sunpath
# get location data form epw file
location = epw.EPW(_epwFile).location
# initiate sunpath based on location
sp = sunpath.Sunpath.fromLocation(location, northAngle = 0, daylightSavingPeriod = None, basePoint =cenPt, scale = scale, sunScale = sunScale)
# draw sunpath geometry
sp.drawAnnualSunpath()
# assign geometries to outputs
...
Finally we ask, how would this code will look if we wanted to make a sunpath for dynamo? Well, it will be exactly the same! Just change ladybuggrasshopper in the second line to ladybugdynamo! Here is the code which is creating the sunpath below.
With this ease of scripting, we hope to involve more of our community members in our development and make it easy for others to use ladybug in their various preferred applications. By the next release, we will produce an API documentation (documentation of all the ladybug classes, methods and properties that you can script with) and begin making tutorials for those interested in getting deeper into Ladybug development.
LADYBUG
1 - Initial Release of Ladybug for Dynamo:
As is evident from the post above, we are happy to announce the first release of Ladybug for Dynamo! You can download the ladybug package from Dynamo package manager. Make sure to download version 0.0.6 which is actually 0.0.1! It took a number of trial and errors to get it up there. Once you have the file downloaded you can watch these videos to get started:
The source code can be find under ladybug-dynamo repository and (as you can already guess) it is using the new code base. It includes a very small toolkit of essential Ladybug components/nodes but it has enough to get you started. You can import weather files, draw sunpaths and run sunlighthours or radiation analyses.
There are two known issues in this release but neither of them is critical. You need to have Dynamo 0.9.1 or higher installed which you can download from here (http://dynamobuilds.com/). It is recommended that you run the scripts with ‘Manual’ run (as opposed to ‘Automatic’) since the more intense calculations can make Dynamo crash in automatic mode.
To put things in perspective, here is how we would map Ladybug for Dynamo vs Ladybug and Honeybee for Grasshopper on the classic ‘Hype graph’. The good news is that what we learned a lot from the last three years, making development of the Dynamo version easier and getting us to the plateau of productivity faster.
We should also note that the current development of the Dynamo interface is behind that of the Ladybug-Core, which means there are a number of features that are developed in the code but haven’t made their way to the nodes yet. They will be added gradually over the next month or two.
If you’re interested to get involved in the development process or have ideas for the development, follow ladybug on Facebook, Twitter and Github. We will only post major release news here. Facebook, github and twitter will be the main channels for posting the development process. There will also be a release of a new ladybug for Grasshopper soon that will use the came Ladybug-Core libraries as the Dynamo interface [Trying hard not to name it as Ladybug 2].
2 - New Project “Icarus” Provides Ladybug Capabilities Directly in Rhino
Speaking of expanded cross-platform capabilities, the talented Miguel Rus has produced a standalone Rhino Plugin off of the original Ladybug code that has been included in this release. After writing his own core C# libraries, Miguel’s plugin enables users to produce sunpath and run sunlight hours analyses in the Rhino scene without need of opening Grasshopper or engaging the (sometimes daunting) act of visual scripting.
This release includes his initial RHP plugin file. It is hoped that Miguel’s efforts will extend some of the capabilities of environmental design to individuals who are unfamiliar with visual scripting, casting the network of our community into new territory. We need your help spreading the word about Icarus since the people who will benefit the most from it have probably not read this far into the release notes. Also, as the project is in the early stages, your feedback can make a great difference. You can download the current release from this link.
Once you download the zip file. Right click and unblock it. Then extract the files under C:\Program Files\Rhinoceros 5 (64-bit)\Plug-ins\ folder. Drag and drop the RHP file into Rhino and you should be ready to go. You can either type Icarus in the command line or open it via the panels. Here is a short video that shows how to run a sunlighhours analysis study in Rhino.
3 - BakeIt Input Now Supports a Pathway to PDF +Vector Programs
As promised in the previous release, the BakeIt_ option available on Ladybug’s visual components has been enhanced to provide a full pathway to vector-based programs (like Illustrator and Inkscape) and eases the export to vector formats like PDFs.
This means that the BakeIt_ operation now places all text in the Rhino scene as actual editable text (not meshes) and any colored meshes are output as groups of colored hatches (so that they appear as color-filled polygons in vector-based programs). There is still an option to bake the colored geometries as light meshes (which requires smaller amounts of memory and computation time) but the new hatched capability should make it easier to incorporate Ladybug graphics in architectural drawings and documents like this vector psychrometric chart.
4 - Physiological Equivalent Temperature (PET) Now Available
Thanks to the efforts of Djordje Spasic, it is now possible to compute the common outdoor comfort metric ‘Physiological Equivalent Temperature’ (PET) with Ladybug. The capability has been included with this release of “Thermal Comfort Indices” component and is supported by a “Body Characteristics” component in the Extra tab. PET is particularly helpful for evaluating outdoor comfort at a high spatial resolution and so the next Honeybee release will include an option for PET with the microclimate map workflow.
5 - Solar Hot Water Components Available in WIP
Chengchu Yan and Djordje Spasic have built a set of components that perform detailed estimates of solar hot water. The components are currently undergoing final stages of testing and are available in the WIP tab of this release. You can read the full release notes for the components here.
6 - New Ladybug Graphic Standards
With the parallel efforts or so many developers, we have made an effort in this release to standardize the means by which you interact with the components. This includes warnings for missing inputs and the ability to make either icons or text appear on the components as you wish (Hi Andres!). A full list of all graphic standards can be found here. If you have any thoughts or comments on the new standards, feel free to voice them here.
7 - Wet Bulb Temperature Now Available
Thanks to Antonello Di Nunzio - the newest member of the Ladybug development team, it is now possible to calculate wet bulb temperature with Ladybug. Antonello’s component can be found under the WIP tab and takes inputs of dry bulb temperature, relative humidity, and barometric pressure.
8 - New View Analysis Types
The view analysis component now allows for several different view studies in addition to the previous ‘view to test points.’ These include, skyview (which is helpful for studies of outdoor micro-climate), as well as spherical view and ‘cone of vision’ view, which are helpful for indoor studies evaluating the overall visual connection to the outdoors.
HONEYBEE
1 - Connection to THERM and LBNL Programs
With this release, many of you will notice that a new tab has been added to Honeybee. The tab “11 | THERM” includes 7 new components that enable you to export ready-to-simulate Lawrence Berkeley National Lab (LBNL) THERM files from Rhino/Grasshopper. THERM is a 2D finite element heat flow engine that is used to evaluate the performance of wall/window construction details by simulating thermal bridging behavior. The new Honeybee tab represents the first ever CAD plugin interface for THERM, which has been in demand since the first release of LBNL THERM several years ago. The export workflow involves the drawing of window/wall construction details in Rhino and the assigning of materials and boundary conditions in Grasshopper to produce ready-to-simulate THERM files that allow you to bypass the limited drawing interface of THERM completely. Additional components in the “11 | THERM” tab allow you to import the results of THERM simulations back into Grasshopper and assist with incorporating THERM results into Honeybee EnergyPlus simulations. Finally, two components assist with a connection to LBNL WINDOW for advanced modeling of Glazing constructions. Example files illustrating many of the capabilities of the new components can be found in there links.
THERM_Export_Workflow, THERM_Comparison_of_Stud_Wall_Constructions
Analyze_THERM_Results, Thermal_Bridging_with_THERM_and_EnergyPlus
Import_Glazing_System_from_LBNL_WINDOW, Import_LBNL_WINDOW_Glazing_Assembly_for_EnergyPlus
It is recommended that those who are using these THERM components for the first time begin by exploring this example file.
Tutorial videos on how to use the components will be posted soon. A great deal of thanks is due to the LBNL team that was responsive to questions at the start of the development and special thanks goes to Payette Architects, which allowed Chris Mackey (the author of the components) a significant amount of paid time to develop them.
2 - Electrical Lighting Components with Enhanced Capabilities for Importing and Manipulating IES Files
Thanks to the efforts of Sarith Subramaniam, it is now much easier and more flexible to include electric lighting in Honeybee Radiance simulations. A series of very exciting images and videos can be found in his release post.
You can find the components under WIP tab. Sarith is looking for feedback and wishes. Please give them a try and let him know your thoughts. Several example files showing how to use the components can be found here. 1, 2, 3.
3- Expanded Dynamic Shade Capabilities
After great demand, it is now possible to assign several different types of control strategies for interior blinds and shades for EnergyPlus simulations. Control thresholds range from zone temperature, to zone cooling load, to radiation on windows, to many combinations of these variables. The new component also features the ability to run EnergyPlus simulations with electrochromic glazing. An example file showing many of the new capabilities can be found here.
Dragonfly Beta
In order to link the capabilities of Ladybug + Honeybee to a wider range of climatic data sets and analytical tools, a new insect has been initiated under the name of Dragonfly. While the Dragonfly components are not included with the download of this release, the most recent version can be downloaded here. An example file showing how to use Dragonfly to warp EPW data to account for urban heat island effect can also be found here. By the next release, the capabilities of Dragonfly should be robust enough for it to fly on its own. Additional features that will be implemented in the next few months include importing thermal satellite image data to Rhino/GH as well as the ability to warp EPW files to account for climate change projections. Anyone interested in testing out the new insect should feel free to contact Chris Mackey.
And finally, it is with great pleasure that we welcome Sarith and Antonello to the team. As mentioned in the above release notes, Sarith has added a robust implementation for electric light modeling with Honeybee and Antonello has added a component to calculate wet bulb temperature while providing stellar support to a number of people here on the GH forum.
As always let us know your comments and suggestions.
Enjoy!
Ladybug+Honeybee development team
PS: Special thanks to Chris for writing most of the release notes!…
ive collaborative environment.
TYPE : Course module and Workshop
The event is open for anybody interested from all the fields of design, including: architecture, interior design, furniture design, product design, fashion design, scenography, and engineering.
1. COURSE MODULE (20-23 April 2014) - optional
+ type: 3 days intensive course regarding basic knowledge in parametric design (LEVEL 1)
+ software: Rhinoceros & Grasshopper
+ plugins: Kangaroo, Weaver Bird, Lunch box, Ghowl, Geco
+ achievements:
- acquainting to the components & the concept of Generative Design
- understanding the strategies in Algorithmic Design
- how to easily insert simple mathematical equation into the project to gain more control
- how to utilize proper plugins with respect to their nature of the project
- interacting with different analysis platforms such as Ecotect & remote controller
- solving several exercises with different scales( 2D- 3D ) during each phase of the workshop
2. WORKSHOP (23-27 April 2014)
A 5 day Design-Based Research Workshop exploring new techniques in Digital Architecture/Fabrication, with a specific focus on the use of generative systems and parametric modeling as tools for creative expression.
Our ultimate goal is to increasing the efficiency of utilizing digital tools in parallel with geometric performance of the primitive design agent.
+ + CONCEPT
Fashion and Architecture are both based on basic life necessities – clothing and shelter.
However, they are also forms of self-expression – for both creators and consumers.
Both fashion and architecture affect our emotional being in many ways.
The agenda of this workshop is to investigate on the overlap between these two areas of design, art & fashion.
Fashion and architecture express ideas of personal, social and cultural identity, reflecting the concerns of the user and the ambition of the age. Their relationship is a symbiotic one and throughout history, clothing and buildings have echoed each other in form and appearance. This only seems natural as they not only share the primary function of providing shelter and protection for the body, but also because they both create space and volume out of flat, two-dimensional materials.
While they have much in common, they are also intrinsically different – address the human scale, but the proportions, sizes and shapes differ enormously.
+ + + OBJECTIVES
So far, Architects have been using techniques such as folding, bending etc. to create space, structural roofs or different other structural shapes.
The agenda of this workshop goes further with the investigation of algorithmic thinking through generative tools Integrated in design.
The challenge is creating a bridge that connects these two areas of design, architecture and fashion that perform at two opposite scales.
+ + + + TECHNICAL BRIEF
In the early stages physical models and low-tech strategies will be used, allowing the participants to gain a greater understanding of materials, fabrication and assembly methods as well as simple, yet pragmatic structural solutions.
Later in the workshop these strategies will be digitalized and elaborated using software visualizing tools such as Rhinoceros and the algorithmic plug-in Grasshopper.…
rves/holes. However, the Kangaroo script itself is prone to locking up so it seems like it might take forever. You can even double click stop the timer from the Windows task bar, I hadn't noticed that before:
You have to use that or right click disable the timer since even with the Reset toggle button input set to True the timer itself locks up the script a bit when you are changing things around.
Just setting the min/max numbers both to a desired mesh size gives a uniform mesh:
Oh weird, it's about if the timer is right click set to so small an interval that it gets ahead of Kangaroo! When you see how long each cycle is taking with the Display > Canvas Widgets > Profiler you just set the timer for above that and the interface comes back into being responsive. It only takes a few Kangaroo cycles to do the inflation, so a full second timer interval is even workable.
A finer mesh:
It's funny running it so slow since it overinflates at first, bulging out, before it equilibrates.
You have control over inflation pressure and mesh stiffness, for a variety of effects.
This is a good system once I realized the timer needed to be mellowed out.
What made it work was the fast custom meshing since a normal mesh is awful and MeshMachine wouldn't work with sharp corner holes at all, breaking out of the boundary even if I fixed curves or vertices or did the equivalent with NURBS surfaces instead of a starting mesh.
There is an initiation time for Kangaroo that doesn't show up on its Profiler time that happens even with the timer off.
There are some fine areas that can't inflate with a reasonable mesh setting:
Worth playing with but no match for ArtCAM since it suffers odd delays in between working fast. If I could get better 2D meshes, that were more adaptive it would be better, but MeshMachine is one of the only re-meshers I know and it's broken for even mildly sharp hole features.
Ah, how about a crude mesh that is then subdivided, guaranteeing inner vertices everywhere? Sort of works, but is still too dense. Way too dense to even do anything. The subdivision triangulates the quads, vastly increasing the mesh wire density. Better just to make a finer initial mesh with plenty of quads.…
Added by Nik Willmore at 12:57am on February 21, 2016
ed file and code below:
Color ColorAt(Mesh mesh, int faceIndex, double t0, double t1, double t2, double t3) { // int rc = -1; var color = Rhino.Display.Color4f.Black;
if( mesh.VertexColors.Count != 0) { // test to see if face exists if( faceIndex >= 0 && faceIndex < mesh.Faces.Count ) { /// Barycentric quad coordinates for the point on the mesh /// face mesh.Faces[FaceIndex].
/// If the face is a triangle /// disregard T[3] (it should be set to 0.0).
/// If the face is /// a quad and is split between vertexes 0 and 2, then T[3] /// will be 0.0 when point is on the triangle defined by vi[0], /// vi[1], vi[2]
/// T[1] will be 0.0 when point is on the /// triangle defined by vi[0], vi[2], vi[3].
/// If the face is a /// quad and is split between vertexes 1 and 3, then T[2] will /// be -1 when point is on the triangle defined by vi[0], /// vi[1], vi[3]
/// and m_t[0] will be -1 when point is on the /// triangle defined by vi[1], vi[2], vi[3].
MeshFace face = mesh.Faces[faceIndex];
// Collect data for barycentric evaluation. Color p0, p1, p2;
if(face.IsTriangle) { p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.B]; p2 = mesh.VertexColors[face.C]; } else { if( t3 == 0 ) { // point is on subtriangle {0,1,2} p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.B]; p2 = mesh.VertexColors[face.C]; } else if( t1 == 0 ) { // point is on subtriangle {0,2,3} p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.C]; p2 = mesh.VertexColors[face.D]; //t0 = t0; t1 = t2; t2 = t3; } else if( t2 == -1 ) { // point is on subtriangle {0,1,3} p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.B]; p2 = mesh.VertexColors[face.D]; //t0 = t0; //t1 = t1; t2 = t3; } else { // point must be on remaining subtriangle {1,2,3} p0 = mesh.VertexColors[face.B]; p1 = mesh.VertexColors[face.C]; p2 = mesh.VertexColors[face.D]; t0 = t1; t1 = t2; t2 = t3; } }
/** double r = t0 * p0.FractionRed() + t1 * p1.FractionRed() + t2 * p2.FractionRed(); double g = t0 * p0.FractionGreen() + t1 * p1.FractionGreen() + t2 * p2.FractionGreen(); double b = t0 * p0.FractionBlue() + t1 * p1.FractionBlue() + t2 * p2.FractionBlue();
ON_Color color; color.SetFractionalRGB(r, g, b);
unsigned int abgr = (unsigned int)color; rc = (int) ABGR_to_ARGB(abgr); **/ var c0 = new Rhino.Display.Color4f(p0); var c1 = new Rhino.Display.Color4f(p1); var c2 = new Rhino.Display.Color4f(p2); float s0 = (float) t0; float s1 = (float) t1; float s2 = (float) t2;
float R = s0 * c0.R + s1 * c1.R + s2 * c2.R; float G = s0 * c0.G + s1 * c1.G + s2 * c2.G; float B = s0 * c0.B + s1 * c1.B + s2 * c2.B; color = new Rhino.Display.Color4f(R, G, B, 1); } } return color.AsSystemColor(); }
…
ort and export from the images below and also from the HELP file of DB in attachments (Page 71: Importing Geometric Data; Page 78-80: Import 3 - D CAD Data). In their HELP file, they mention about "import geometric data".
However, regarding the input of schedules, loads, constructions and etc., DB normally uses "Component " and "Template" (Page 29: Templates And Components; Page 591: Templates; Page 533: Components). "Templates" are databases of typical generic data, including Activity templates, Construction templates, Glazing templates, Facade templates, HVAC templates, Location Templates, and etc. "Component " are databases of individual data items (e.g. a construction type, material, window pane).
Both "Component " and "Template" are allowed to be imported and exported by using "Import / Export library data" command (.ddf format - DB Database File; Page 734: Import Components/Templates, Export Components/Templates). DB also allows us to build up our own libraries of templates and components (Page 731: Library Management; Page 733: Template Library Management).
In order to import both geometric information and other information related to schedules, loads, constructions and etc. from GH to BD, we supposed the following two ways:
1. GH(HB+GB) --> gbXML (both geometric and "Component " and "Template" information) --> DB
This is the way we most prefer. We did see information related to schedules, loads, constructions encoded in the gbXML file generated by GB, but still do not know the reason why DB did not take this information (I also mentioned this in Q6 within the gh file). We assume this might because the gbXML file we create encodes the schedules based on a different template / schema than the one DB expects. We also post this question to the DB forum for help.
(http://www.designbuilder.co.uk/component/option,com_forum/Itemid,25/page,viewtopic/p,13755/#13755)
2. GH(HB+GB) --> gbXML (geometric information only) + .ddf ("Component " and "Template" information only) --> DB
If the first way doesn't work and DB only takes geometric information from the gbXML, then we might think of the other way - generating the .ddf files from GH(HB+GB) to pass the schedule, load and construction information to DB.
I was wondering if it is feasible for HB and GB to have this function? And what is your suggestion to achieve this?
In addition, we notice that DB can export XML files (not gbXML), so we are trying to figure out if DB also accepts / reads the XML file. If so, we might be able to convert the gbXML (with both geometric and schedule information) to XML. What do you think about that?
Thank you again for all your help!
Best,
Ding
DB import
DB export
Template libraries
Component libraries
…
y using the Honeybee_Update Honeybee component.
The video below (best viewed in full-screen mode) provides an idea of what these components are capable of being used for:
The video below shows how these components can be used in an existing Honeybee project (for additional links please open this video in youtube):
I have uploaded two examples as Hydra files that show how these components can be used for grid-point and image-based simulations:
Example1 : Grid Point Calculations
Example2: Image based simulation
Finally, a more esoteric application is demonstrated in this video:
These components are still in the beta-testing stage. Some of the limitations of the components are:
1. Only Type C photometry IES files are supported at present.
2. Rhino is likely to get sluggish if there are too many luminaires (i.e. light fixtures) present in a scene.
3. Due to the spectral limitations of the ray-tracing software (RADIANCE), simulations involving color mixing might not be physically realizable.
Additional details about photometric and spectral calculations are probably an overkill for this forum. However, I'd be glad to answer any related questions. Please report any bugs or request new features either on this forum or on Github.
Mostapha, Leland Curtis, Reinhardt Swart and Dr. Richard Mistrick provided valuable inputs during the development of these components.
Thanks,
Sarith
Update 16th January 2017:
An example with some new components and bug fixes since the initial release announcement can be found here
…
Introduction to Grasshopper Videos by David Rutten.
Wondering how to get started with Grasshopper? Look no further. Spend an some time with the creator of Grasshopper, David Rutten, to learn the
ay how many valid permutations exist.
But allow me to guesstimate a number for 20 components (no more, no less). Here are my starting assumptions:
Let's say the average input and output parameter count of any component is 2. So we have 20 components, each with 2 inputs and 2 outputs.
There are roughly 35 types of parameter, so the odds of connecting two parameters at random that have the same type are roughly 3%. However there are many conversions defined and often you want a parameter of type A to seed a parameter of type B. So let's say that 10% of random connections are in fact valid. (This assumption ignores the obvious fact that certain parameters (number, point, vector) are far more common than others, so the odds of connecting identical types are actually much higher than 3%)
Now even when data can be shared between two parameters, that doesn't mean that hooking them up will result in a valid operation (let's ignore for the time being that the far majority of combinations that are valid are also bullshit). So let's say that even when we manage to pick two parameters that can communicate, the odds of us ending up with a valid component combo are still only 1 in 2.
We will limit ourselves to only single connections between parameters. At no point will a single parameter seed more than one recipient and at no point will any parameter have more than one source. We do allow for parameters which do not share or receive data.
So let's start by creating the total number of permutations that are possible simply by positioning all 20 components from left to right. This is important because we're not allowed to make wires go from right to left. The left most component can be any one of 20. So we have 20 possible permutations for the first one. Then for each of those we have 19 options to fill the second-left-most slot. 20×19×18×17×...×3×2×1 = 20! ~2.5×1018.
We can now start drawing wires from the output of component #1 to the inputs of any of the other components. We can choose to share no outputs, output #1, output #2 or both with any of the downstream components (19 of them, with two inputs each). That's 2×(19×2) + (19×2)×(19×2-1) ~ 1500 possible connections we can make for the outputs of the first component. The second component is very similar, but it only has 18 possible targets and some of the inputs will already have been used. So now we have 2×(18×2-1) + (18×2-1)×(18×2-1) ~1300. If we very roughly (not to mention very incorrectly, but I'm too tired to do the math properly) extrapolate to the other 18 components where the number of possible connections decreases in a similar fashion thoughout, we end up with a total number of 1500×1300×1140×1007×891×789×697×...×83×51×24×1 which is roughly 6.5×1050. However note that only 10% of these wires connect compatible parameters and only 50% of those will connect compatible components. So the number of valid connections we can make is roughly 3×1049.
All we have to do now is multiply the total number of valid connection per permutation with the total number of possible permutations; 20! × 3×1049 which comes to 7×1067 or 72 unvigintillion as Wolfram|Alpha tells me.
Impressive as these numbers sound, remember that by far the most of these permutations result in utter nonsense. Nonsense that produces a result, but not a meaningful one.
EDIT: This computation is way off, see this response for an improved estimate.
--
David Rutten
david@mcneel.com
Poprad, Slovakia…
Added by David Rutten at 12:06pm on March 15, 2013