size component supported only ground PV panels and angled roof PV panels.
Download the newest PV SWH system size component from here (Click on "View Raw" to download it. Then move the downloaded .ghuser file to File->Special Folders->User Objects Folder, an confirm to overwrite it with previously located one).
Just a few opinions on the project you are currently working on:This kind of fixed, non-transparent (overhang) PV panels attached to a building facade are vert convenient for locations with higher latitudes.The reason for this is because they (fixed overhang PV panels) are dimensioned according to the sun position at summer solstice. Elevation angles on summer solstice at higher latitude locations are lower, than those of lower latitude locations.Due to Incheon's low latitude (37), you will get rather short length of the PV panels* : less than 10 centimeters (0.097 meters in the attached .gh file below). As you have mentioned, Galapagos needs to be used too.I will just mention some of the good and bad ways in which the upper issue could be somewhat avoided:1) Increasing the vertical distance between PV panels (PV panels appear above every second window).2) Increase the tilt angle. This will increase the length of PV panels also, but will decrease the final annual AC energy output.An example of this solution has been applied at FKI building in Seoul (latitude: 37N):I already did some tests (with tilt angles: 40, 45, 55) and this does not seem like a good solution, though.3) Shrinking the "sun window" by using the minimalSpacingPeriod_ input. In Photovoltaics, a planner is suppose to make the 9h to 15h part of the sun window free of any obstructions. If you try to decrease the "sun window" to 10 to 14h, the length of your PV panels will increase. You can try to experiment a little bit with this (set your minimalSpacingPeriod_ to 21th of June 10 to 14hours). In general, shrinking the sun window on summer solstice is not a good principle during planning.4) Using tracking PV panels, not fixed ones. But Ladybug Photovoltaics components do not support this kind of PV systems. They only support fixed ones.I would personally go with the first option. You can also experiment with the second and third one.Comment back if you have any other questions.-----------------------* By "length of the PV panels" I mean the: tiltedArrayHeight_ input of the PV SWH system size component.…
answer further on Friday.
The "ghdoc" variable and rhinoscriptsyntaxThe ghdoc variable is provided by the component if you select it as "target".You might ask yourself: "why do we need it"?Its use comes from the very design of the established RhinoScript library. This library is imperative, which means it is build from a set of procedures or functions that act on various geometrical types. Additionally, there is one level of indirection: most of the time, the user does not work with the geometry itself in the variable, but rather with Guid of geometry that is present in a document. This is exactly what ghdoc is: it is the document that the RhinoScript library always implicitly targets with all AddSomething() calls (for example, AddLine()).
Based on this comment...RhinoScript use within GhPython may be less idealThat comment is from a previous version of this component that did not have the ghdoc yet.With the ghdoc variable, the standard Rhino document target of RhinoScript is replaced, therefore we can use Grasshopper while leaving the Rhino document unchanged. This saves uncountable Undo's, and makes it easy to structure ideas through the definition graph
...is the rhinoscriptsyntax target irrelevant if using solely RhinoCommon classesYes. If you create class instances (objects), you will need to create also your own collection objects to store them (mostly lists, trees). You can imagine the ghdoc as being an alternative to them, just that you do not access data by index (number), but by Guid. So you can use the RhinoScript or the RhinoCommon libraries independently or mix them. The RhinoScript implementation in Rhino is open-source and is all written in RhinoCommon. Also the ghdoc implementation is open-source, and is here.
RhinoScript and/or RhinoCommon objects which are not recognized as valid Grasshopper geometryYes, sure, Grasshopper handles only a portion of all available types. Basically, unhandled types are all the types that do not exists in the 'Params' tab. For example, there is no textdot and no leader, so on line 149 there is a throw statement and all TextDot calls (about line 350) are commented out. When/if Grasshopper one day will support these types, these calls will be implemented.
DataTreeHere is a small sample. However, I think that 80% of the times it is not necessary to program for DataTrees, as the logic itself can be applied per-list and Grasshopper handles list-iteration.
I hope this helps,
- Giulio_______________giulio@mcneel.comMcNeel Europe…
ort and export from the images below and also from the HELP file of DB in attachments (Page 71: Importing Geometric Data; Page 78-80: Import 3 - D CAD Data). In their HELP file, they mention about "import geometric data".
However, regarding the input of schedules, loads, constructions and etc., DB normally uses "Component " and "Template" (Page 29: Templates And Components; Page 591: Templates; Page 533: Components). "Templates" are databases of typical generic data, including Activity templates, Construction templates, Glazing templates, Facade templates, HVAC templates, Location Templates, and etc. "Component " are databases of individual data items (e.g. a construction type, material, window pane).
Both "Component " and "Template" are allowed to be imported and exported by using "Import / Export library data" command (.ddf format - DB Database File; Page 734: Import Components/Templates, Export Components/Templates). DB also allows us to build up our own libraries of templates and components (Page 731: Library Management; Page 733: Template Library Management).
In order to import both geometric information and other information related to schedules, loads, constructions and etc. from GH to BD, we supposed the following two ways:
1. GH(HB+GB) --> gbXML (both geometric and "Component " and "Template" information) --> DB
This is the way we most prefer. We did see information related to schedules, loads, constructions encoded in the gbXML file generated by GB, but still do not know the reason why DB did not take this information (I also mentioned this in Q6 within the gh file). We assume this might because the gbXML file we create encodes the schedules based on a different template / schema than the one DB expects. We also post this question to the DB forum for help.
(http://www.designbuilder.co.uk/component/option,com_forum/Itemid,25/page,viewtopic/p,13755/#13755)
2. GH(HB+GB) --> gbXML (geometric information only) + .ddf ("Component " and "Template" information only) --> DB
If the first way doesn't work and DB only takes geometric information from the gbXML, then we might think of the other way - generating the .ddf files from GH(HB+GB) to pass the schedule, load and construction information to DB.
I was wondering if it is feasible for HB and GB to have this function? And what is your suggestion to achieve this?
In addition, we notice that DB can export XML files (not gbXML), so we are trying to figure out if DB also accepts / reads the XML file. If so, we might be able to convert the gbXML (with both geometric and schedule information) to XML. What do you think about that?
Thank you again for all your help!
Best,
Ding
DB import
DB export
Template libraries
Component libraries
…
ay how many valid permutations exist.
But allow me to guesstimate a number for 20 components (no more, no less). Here are my starting assumptions:
Let's say the average input and output parameter count of any component is 2. So we have 20 components, each with 2 inputs and 2 outputs.
There are roughly 35 types of parameter, so the odds of connecting two parameters at random that have the same type are roughly 3%. However there are many conversions defined and often you want a parameter of type A to seed a parameter of type B. So let's say that 10% of random connections are in fact valid. (This assumption ignores the obvious fact that certain parameters (number, point, vector) are far more common than others, so the odds of connecting identical types are actually much higher than 3%)
Now even when data can be shared between two parameters, that doesn't mean that hooking them up will result in a valid operation (let's ignore for the time being that the far majority of combinations that are valid are also bullshit). So let's say that even when we manage to pick two parameters that can communicate, the odds of us ending up with a valid component combo are still only 1 in 2.
We will limit ourselves to only single connections between parameters. At no point will a single parameter seed more than one recipient and at no point will any parameter have more than one source. We do allow for parameters which do not share or receive data.
So let's start by creating the total number of permutations that are possible simply by positioning all 20 components from left to right. This is important because we're not allowed to make wires go from right to left. The left most component can be any one of 20. So we have 20 possible permutations for the first one. Then for each of those we have 19 options to fill the second-left-most slot. 20×19×18×17×...×3×2×1 = 20! ~2.5×1018.
We can now start drawing wires from the output of component #1 to the inputs of any of the other components. We can choose to share no outputs, output #1, output #2 or both with any of the downstream components (19 of them, with two inputs each). That's 2×(19×2) + (19×2)×(19×2-1) ~ 1500 possible connections we can make for the outputs of the first component. The second component is very similar, but it only has 18 possible targets and some of the inputs will already have been used. So now we have 2×(18×2-1) + (18×2-1)×(18×2-1) ~1300. If we very roughly (not to mention very incorrectly, but I'm too tired to do the math properly) extrapolate to the other 18 components where the number of possible connections decreases in a similar fashion thoughout, we end up with a total number of 1500×1300×1140×1007×891×789×697×...×83×51×24×1 which is roughly 6.5×1050. However note that only 10% of these wires connect compatible parameters and only 50% of those will connect compatible components. So the number of valid connections we can make is roughly 3×1049.
All we have to do now is multiply the total number of valid connection per permutation with the total number of possible permutations; 20! × 3×1049 which comes to 7×1067 or 72 unvigintillion as Wolfram|Alpha tells me.
Impressive as these numbers sound, remember that by far the most of these permutations result in utter nonsense. Nonsense that produces a result, but not a meaningful one.
EDIT: This computation is way off, see this response for an improved estimate.
--
David Rutten
david@mcneel.com
Poprad, Slovakia…
Added by David Rutten at 12:06pm on March 15, 2013
ss lots of questions,Hope guys show me some more different ways to figure out thoes kinds of problems,Thanks.
That is a construction project,the balconies should be overhang between 1 to 3 meters.
Program A is a patten consist of increasing balconies as the floors get upper.(In the picture is 29 at the first floor and ended with 2 more balconies for each floor, )Each part for a different floor,the twelfth floor have 29+(12-1)*2=51 balconies.
Questions From A,
A1:How to use the {(series)} to creat this atrium,As the floors increase the number of the balconies change by arithmetic progression.
A2:How to control the angle of the balconies,both the angle with floor and the balconies ending part.
Program B is use line to shape the commercial atrium,program A is more small pieces of rectangles.The {(TweenCrv)} command.
Questions From B,
B1:How to draw random points between the 1 to 3 meters region of the balcony,And those point form a shape also belongs to that region.
B2:Use a curve or other ways to control the changing speed of each floors' balcony.Right now the balcony is a Linear change.
Thanks for your Help.
Q1:Is there a way in Grasshopper to control the model to Modulus,less different unit parts to build such a Atrium.(For Exanple,only use 900mm and 600mm two different width of the Glass railings to bulid the model A OR B)…
ake a modest notice about the two new Ladybug components, one of which creates a 3d terrain shading mask and another one which visualizes and exports horizon angles. A terrain shading mask is essentially a diagram which maps the silhouette of the surrounding terrain (hills, valleys, mountains, tree tops...) around the chosen location, and account for the shading losses from the terrain. It can be used as a context_ input in mountainous or higher latitude regions for any kind of sun related analysis: sunlight hours analysis, solar radiation analysis, view analysis, photovoltaics/solar water heating sunpath shading...
My home town is an example of the shading caused by the terrain. Here is how it looks from the tallest building in the town:
And the created terrain shading mask:
A mask for any land location up to 60 degrees North can be created:
There will also be a support for a few major cities above this limit.
Both Terrain shading mask and Horizon angles components can be downloaded from here. An example .gh file can be found in here.
Component will prompt the user to download and copy certain files in order to be able to run.
It was created with assistance from Dr. Bojan Savric. Support on various issues was further given by: Dr. Graham Dawson, Dr. Alec Bennett, Dr. Ulrich Deuschle, Andrew T. Young, LiMinlu, Jonathan de Ferranti, Michal Migurski, Christopher Crosby, Even Rouault, Tamas Szekeres, Izabela Spasic, Mostapha Sadeghipour Roudsari, Dragan Milenkovic, Chen Weiqing, Menno Deij-van Rijswijk and gis.stackexchange.com community.
I hope somebody might find the components useful.…
th one element which is a list of 10 numbers?
I can flatten it and get (I think) a list of 10 elements (even though when I hover over the output of "Flatten" it says "Tree(T) as tree"). I'm surprised I can flatten at all what would appear to common sense to be a simple list of 10 numbers.
I'm hoping that if I can get this answered it will become obvious why we have trees of lists rather than just lists of lists as you would in most computer languages. That's my real goal - to understand the purpose of adding what seems like an unnecessary complication - trees - to the concept of lists in GH. It seems to me as though a "tree" is just a list of other "trees" until you get to the leaves where you can have "lists" which are identical to trees but can have something other than a tree in them. Whether you can have lists of trees or trees with no lists I'm unclear on. Do the leaves of trees have to be lists? Do lists have to be contained in trees? It would appear from the series example where a tree is produced for no obvious reason to contain the list that this is the case but given that you can flatten it, I guess not - or is the "List" I see in the param viewer just another type of "tree"?
I've found many tutorials that talk about how to manipulate trees and lists and I've managed to get along fairly well with them so far, but nothing seems to explain the reasoning behind the existence of trees and the philosophy for how and when they should be used and when lists should/could be used and precisely what the difference is between them.
Sorry to be long winded but I'm so confused!
Darrell Plank
P.S. I've seen David Rutten's diagram with the colored leaves in Grasshopper Primer 2 and that seems helpful. It would appear that trees can only have lists at their leaves and lists can't have trees although I'm not sure that it comes out and says that directly but at least there are no examples of this shown in his tree diagram. I thought I had it down pretty much so decided to test myself. Apparently I'm as confused as ever:
It certainly appears to me that this tree has two levels - a first level with one limb and a second with 10 limbs - and that I should be able to index it with {0;0} and retrieve a tree with one item in it - the list {0}. The panel data seems to confirm this with indices of {0;0;0}, etc. so I put this path in with quite a bit of confidence that it would work and...bust. The error reads "Path {0;0} does not exist within this tree". Huh? Again, I'm just so confused.…
Added by Darrell Plank at 12:17am on January 20, 2015
it seems that was this. Now all is working fine !
Glad that it worked! But I am still a bit worried. Gismo components only modify the gdal-data/osmconf.ini file and no other MapWinGIS file. So your MapWinGIS installation files should not be compromised. The fact that you did not get the "COM CLSID" error message when running the "Gismo Gismo" component suggests that MapWinGIS has been properly installed. So I wonder if the cause for the permanent "invalid shapes" warning has again something with the fact that your system is again not allowing the MapWinGIS to properly edit the osmconf.ini. Maybe this problem will appear again, and again, and reinstallation of MapWinGIS every time can be somewhat bothersome.
- About the terrain generation, is it possible to have the texture from google or other provider mapped onto the terrain surface from gismo component ? (Same as using the ladybug terrain generator in fact). I try to used the image extracted by ladybug component and then applied it to the gismo terrain but the texture is rotated by 90°.
The issue with the rotation can be solved by swapping/reversing the U,V directions of the terrain surface. A slightly more important issue is that terrain surface generated with Gismo "Terrain Generator" component might have a bit smaller radius than what the radius_ input required. This stems from the fact that the terrain data first needs to be downloaded in geographic coordinate system, and then projected. Some projecting issues may occur at the very edges of the projected terrain, so I had to slightly cut out the very edges of the terrain which results in the actual terrain diameters being slightly shorted in both directions. This means that if you apply the same satellite image from Ladybug "Terrain Generator" component to Gismo "Terrain Generator" component the results may not be the same.I attached below a python component which tries to solve this issue by extending the edges of Gismo "Terrain Generator" terrain, and then cutting them with the cuboid of the exact dimensions as the radius_ input. Have in mind that this extension of the original terrain at its edges is not a correct representation of the actual terrain in that location. But rather just an extension of the isoparameteric curve of the terrain surface. So basically: some 0 to 10% (0 to 10 percent of the width and length) of the terrain around all four edges is not the actual terrain for that location, but rather just its extension.The python component is located at the very right of the definition attached below.
Also, if you would like to use the satellite images from Ladybug "Terrain Generator" component along with "OSM shapes", sometimes you may find slight differences in position of the shapes. This is due to openstreetmap data not being based on Google Maps (that's what Ladybug "Terrain Generator" component is using), but rather on Bing, MapQuest and a few others.
- About the requiredKeys_ input of OSM shapes, I understand what you mean and your advice, but in most cases I use it, the component was working fine even without input. I think it's better to extract all tags, values and keys of the selected area, instead of searching for specific ones as I try to find all data related to what I want after, isn't it ? To check what keys are present on the area also.
Ineed, you are correct.I though you were trying to only create a terrain, 3d buildings and maybe find some school or similar 3d building, for these two locations. The recommendation I mentioned previously is due to shapefiles having a limit (2044) to how many keys it can contain. This requires further testing of some big cities locations with maybe larger radii, which I haven't performed due to my poor PC configuration. But in theory, I imagine that it may happen that a downloaded .osm file may have more than 2044 keys. In that case shapefile will only record 2044 of them, and disregard the others. That was my point.But again 2044 is a lot of keys, and I haven't been checking much this in practice. For example, when I set the radius_ to 1000 meters, and use your "3 Rue de Bretonvilliers Paris" location I get around 350 something keys, which is way below the 2044.Another reason why one should use the requiredKeys_ input is to make the Gismo OSM components run quicker: for example, the upper mentioned 350 something keys will result in 350 values for each branch of the "OSM shapes" component's "values" output.Which means if you have 10 000 shapes, the "OSM shapes" component will have 10 000 branches with 350 items on each branch (values). This can make all Gismo OSM components very heavy, and significantly elongate the calculation process.With requiredKeys_ input you may end up with only a couple of tens of items per each branch.Sorry for the long reply.…
Added by djordje to Gismo at 8:57am on June 11, 2017
ers and researchers, programmers and artists, professionals and academics who come together for 4 days of intense collaboration, development, and design.
The sg2012 Workshop will be organised around Clusters. Clusters are hubs of expertise. They comprise of people, knowledge, tools, materials and machines. The Clusters provide a focus for workshop participants working together within a common framework.
Clusters provide a forum for the exchange of ideas, processes and techniques and act as a catalyst for design resolution. The Workshop is made up of ten Clusters that respond in diverse ways to the sg2012 Challenge Material Intensities.
Applicants to the sg2012 Workshop will select their preferred cluster from the following:
Beyond Mechanics
Micro Synergetics
Composite Territories
Ceramics 2.0
Material Conflicts
Transgranular Perspiration
Reactive Acoustic Environments
Form Follows Flow
Bioresponsive Building Envelopes
Gridshell Digital Tectonics
More information about the Workshop and Clusters can be found here:
http://smartgeometry.org/index.php?option=com_content&view=article&id=116&Itemid=131
The application process will close on January 15th, 2012.
Full Fee $1500
Reduced Fee $750
Scholarship Fee $350
Fees include attendance to both the workshop and conference from March 19th-24th.
Reduced Fee and Scholarships are available only for Academics, Students and Young Practitioners, and are awarded during a competitive peer review process.
sg2012 takes place from 19-24 March 2012 at EMPAC (http://empac.rpi.edu/) and is hosted by Rensselaer Polytechnic Institute in Troy, upstate New York USA. The Workshop and Conference will be a gathering of the global community of innovators and pioneers in the fields of architecture, design and engineering.
The event will be in two parts: a four day Workshop 19-22 March, and a public conference beginning with Talkshop 23 March, followed by a Symposium 24 March. The event follows the format of the highly successful preceding events sg2010 Barcelona and sg2011 Copenhagen.
sg2012 Challenge Material Intensities
Simulation, Energy, Environment
Imagine the design space of architecture was no longer at the scale of rooms, walls and atria, but that of cells, grains and vapour droplets. Rather than the flow of people, services, or construction schedules, the focus becomes the flow of light, vapour, molecular vibrations and growth schedules: design from the inside out.
The sg2012 challenge, Material Intensities, is intended to dissolve our notion of the built environment as inert constructions enclosing physically sealed spaces. Spaces and boundaries are abundant with vibration, fluctuating intensities, shifting gradients and flows. The materials that define them are in a continual state of becoming: a dance of energy and information. Material potential is defined by multiple properties: acoustical, chemical, electrical, environmental, magnetic, manufacturing, mechanical, optical, radiological, sensorial, and thermal. The challenge for sg2012 Material Intensities is to consider material economy when creating environments, micro-climates and contexts congenial for social interaction, activities and organisation. This challenge calls for design innovation and dialogue between disciplines and responsibilities. sg2010 Working Prototypes strove to emancipate digital design from the hard drive by moving from the virtual to the actual in wrestling with the tangible world of physical fabrication. sg2011 Building the Invisible focused on informing digital design with real world data. sg2012 Material Intensities strives to energise our digital prototypes and infuse them with material behaviour. They have the potential to become rich simulations informed by the material dynamics, chemical composition, energy flows, force fields and environmental conditions that feed back into the design process.
More information can be found at http://www.smartgeometry.org
Follow us on Twitter at http://twitter.com/smartgeometry…
Added by Shane Burger at 12:29pm on December 13, 2011
thing that MicroStation does (or doesn't). The eternal debate between us is that they focus to the so called BIM aspect of things (and obviously on interoperability matters - that said IFC2*4 is" implemented" in certain Bentley verticals like BA and others) whilst I'm after assembly/component puzzles (and on that matter ... MS ...hmm... to put it politely is not exactly CATIA and/or NX, he he).
On the other hand this paranoid obsession with Level/Layer driven CAD (I hate it) defines a red thick line between CAD and MCAD - because the most intelligent importer can't emulate the way that Siemens NX/CATIA classifies objects - and without control power means nothing.
On the other hand Microstation V9 (...soon) has interesting scripting capabilities (think Modo rather Generative Components) ... meaning that Grasshopper could work there in a rather nice way. I think that I must talk for that to Ray (he recently ditched the ancient legacy MS render engine in favor for the Luxology/Nexus engine). Ray still is negative to buy Act3D mind (hope that you know the mother of visual scripting - the Quest3D VR thing).
On the other hand - within the broad AEC aspect - things these days are different (especially in fast developing countries the likes of UAE, Saudi Arabia, certain ex USSR "democracies" etc etc). Studies are outsourced even at Preliminary Design stage to various sub-contractors (they undertake the Study completion per discipline as well). This means that N separate groups doing M aspects of the whole ... meaning entropy^(N*M) - that's chaos in plain English.
With this in mind I'm quite (a lot) skeptical about the practical meaning of the whole exchange thing in AEC - at least with regard the countries mentioned (not to mention that several portions of a modern AEC thing are made via MCAD apps - chaos^chaos.
I'll back with more focused issues on that matter.
But the big question is: Grasshopper of Generative Components? Well...let's talk serious SS bikes instead: think a Ducati 1198 and a BMW S1000RR (I have them both): which is "best"? The thing is that not always the best bunny is the fasted bunny and not always the fasted bunny is the best bunny.
Cheers,
Peter
…