ported to Rhino and "set" in Grasshopper, i trim both surfaces from their rectangular bases so that when sDivide is used it creates and distributes the same number of points on each surface.But heres the problems: a) if i use the "trimmed" surfaces with SrfGrid it errors warning: "A point in the grid is null. fitting operation aborted".I'd learned this was caused by "nulls" replacing position Data Items when the rectangular grid(surface base) was trimmed away. So i used Clean Tree which worked removing all nulls, then Shift Paths\Flip Matrix to create line-endpoint pairs for Polyline\Evaluate Curve. I Flattened the last Flip Matrix placing all data items in one source for SrfGrid, like in the working Untrim\CopyTrim definition.This time,.b) SrfGrid errored with: "The UCount value is not valid for this amount of points",.So, i substituted a 356 value, numeric Slider in the Addition B param., and tested its range until a valid UCount was found. Then SrfGrid fitted a surface thru the points, BUT,d) those SrfGrid surfaces are extremely deformed even thought the points preceding it from Evaluate Curve are accurate,SEE: def: "3b-RGH_SurfaceBlend.gh",AND,.a2) if i use Untrim with CopyTrim then SrfGrid works, but since the Jokers limbs WILL be in different surface positions then the blends between the Arm (for example) will rise from its relative FLAT position on the untrimmed Source surface to the Arm on the Target surface, rather than morphing from the Corresponding Arm position on the Source surface,. ..see def.: "4-RGH_SurfaceBlend.gh"So please let me know,..1) how to produce accurate surfaces from SrfGrid in def.: "3b-RGH_SurfaceBlend.gh",. ..(NOTE: BOTH these def's contain 2 indentical, "internalized" surfaces, but if def. 3b can be made to work it will also work with Dis-similar surfaces)2) which component to use or how else to determine the correct UCount value for a specified amount of points(ie:155), re: SrfGrid error: "The UCount value is not valid for this amount of points",.3) how else to force SrfGrid to work with Trimmed surfaces?, AND,..4) how to force intersurface, point-blend correspondence lines: Polylines(PLine) to be connected between correctly! correponding positions (Limbs) on the surfaces?,
Really! appreciate all help, definitions and kind generosity common to this knowledgable membership,
Cheers!,
Jeff…
50 and reduced the 'cell size' slider to 0.5. When the 'Azimuth' angle is changed to 180 +- 90 (dawn or dusk), the points are widely dispersed, reducing the density and increasing the number of cells in the "sparse grid". Under these conditions, the number of cells was ~2000 and the Profiler time for 'Boundary' went up to a full minute or more each time 'Altitude' or 'Azimuth' was changed.
So I created this code to benchmark some alternatives and found two interesting things:
'Boundary' surface performance (v.1) is not linear. As the number of surfaces goes from 1000 to 2000, the time per surface goes up dramatically.
I tried three alternatives for creating a rectangular surface at a given point that are all substantially faster: v.2, v.3 and v.4. For 2000 points, v.4 is 150 times faster than v.1 !!!
Performance of v.2, v.3 and v.4 are similar and all scale up very well. To benchmark beyond 2000 points, I recommend disabling the VERY SLOW v.1. At 5000 points the 'Pop2D' component takes ~11.3 seconds but v.3 and v.4 take less than one second to generate 5000 surfaces!
See boundary_2015Nov19a.gh attached.
So I replaced the 'Rectangle' and 'Boundary' components in my sun reflection model with v.4 in focus_2015Nov19b.gh (also attached) and the performance is amazing.
I'm sure someone has mentioned this performance issue with 'Boundary' on the forum before but as with many things, I didn't realize what a major obstacle it can be until I discovered this for myself.…
Added by Joseph Oster at 9:16pm on November 19, 2015
grout lines, a tile surface and tile perimeter poly line). I then use that as a Mesh (from Rhino) in the second definition.
2. I can tile out the mesh surface and rotate all the tiles in 90 deg. increments.
To get what I wanted. I took the Mesh and have copied it in series to make a grid. I can then control the dimensions of the grid. X and Y extents. I can also rotate the tiles around their centers.
The spacing of the grid is set from an edge curve of the tile (or mesh). This sets the size of the squares in the grid themselves.
See definition, images and Rhino 4 File, to give the definitions a shot. I have labeled how to use them.
My question -- how can I randomly rotate squares in my grid? I would like the deg of rotation to be random and also which tiles they are.
Also how might I rotate (every other tile) for example? So that I can control the pattern more?
Thoughts?
Thanks!
…
ror when it comes to points on edges of the surface.I guess it is because normal vectors at a few of points are invalid. After all, because of these invalid points, an error message comes out which is saying " Runtime error (PythonException) : Unable to add polyline to document " and it results in no output. Please give me some help if you know how to handle this problem. I post a code below.Thanks in advance.
---------------------------------------------------------------------------------------------
import Rhinoimport rhinoscriptsyntax as rsimport mathimport ghpythonlib.components as gh
output_crvs = []
for pt1 in input_pt :output_pts = []newPt = pt1output_pts.append(newPt)
while len(output_pts) <= 100: newPt = outputpoint(base_srf, newPt, distance_factor) output_pts.append(newPt)
output_crv = rs.AddPolyline(output_pts)output_crvs.append(output_crv)A = output_crvs
def outputpoint(base_srf, input_pt, distance_factor):centre_point = rs.AddPoint(0,0,0)height_point = rs.AddPoint(0,0,10)
zaxis = rs.VectorAdd(centre_point, height_point)
cp_pt = rs.SurfaceClosestPoint(base_srf, input_pt)normal_vector = rs.SurfaceNormal(base_srf, cp_pt)drain_vector = rs.VectorCrossProduct(normal_vector, zaxis)
dvector2 = rs.VectorUnitize(drain_vector)dvector3 = rs.VectorRotate(dvector2, 90, normal_vector)
mpt = gh.DeconstructVector(distance_factor*dvector3)moved_pt = rs.PointAdd(input_pt, mpt)moved_uv = rs.SurfaceClosestPoint(base_srf, moved_pt)output_pt = rs.EvaluateSurface(base_srf, moved_uv[0], moved_uv[1])
return output_pt…
g from a list of 12 items I would find all the combinations taking just 4 at time.
I'd use a Stream gate that takes the indexes of the items and pass them to a list item in order to select just the items of the combination. Doing so I can choose a single combination of index at time to pass to the list item.
In this moment all the data come out from the first gate, all the others are empty.
If I pass these index to the list item it gives me an error (probably because of the data structure).
*long version*
I start from a list of 12 segments, all of them with the starting point in common and the ending point distributed regularly in the space. It's a quite simple starting point.
What I'm trying to achieve is to find all the possible spatial configurations made of 2, 3, 4 segments. I started with 2 segments so I've 12^2=144 possible configurations but just 4 different configurations that can intuitivelly be recognized (60°, 90°, 120°, 180°).
Doing the same with 3 segments generates 12^3=1728 configurations and I don't know how many different ones. With 4 segments I've got 12^4=20736 possible configurations.
As you can imagine many configurations are identical but just with a different orientation so at the end I'll have to parse geometrically the output to delete duplicates (I'll address this later on).
Please could you help me to figure out how to mix these segments in different configurations?
Thank you in advance.…
per bake commands to bake the connected geometry with the corresponding materials.
mxDiff is a simple diffuse material. Only reflectance color for 0° and 90° are exposed.
mxEmit is a basic emitter material. You can set light color, power and efficiacy of the emitter.
mxBasic is the most complex material for now. You can set all the properties of a single layer material including. Use this for transparent materials.
mList is your way if you don't want to create your own materials. This component returns a list of all the materials on the Maxwell scene manager. Make sure this is evaluated after you add your own materials if you want to see them in the list.…
ther math and logic. i can usually conceptualise what i want to do and cobble some semi working thing together but don't know which components to use and how to patch it. so i'm super happy to have someone who knows what he's doing to find this interesting.
and i'm glad you mention the fanned frets again, there is one input parameter that's still missing for the multiscale frets to be fully parametric, it's the angle of the nut or which fret should be straight. it depends a bit on personal preferences and playing posture what is more comfortable. so being able to adjust this easily would be cool. again i have no idea how the maths for that work or if you can just rotate each fret the same amount around it's middle point. The input either as fret number (for the straight fret) or as a simple slider from bridge to nut should do as input setting.
Here are the two extremes and the middle ground:
i've been thinkin today while analysing your patches and cleaning up my mess what exactly the monster should do.
Here are the input parameters needed, i think it's the complete list
scale length low E string
scale length high e string
fret angle/straight fret
string width at nut
string width at bridge
number of frets
fretboard overhang at nut (distance from string to fretboard bounds)
fretboard overhang at last fret
string gauges
string tensions
fretboard radius at nut (for compound radius fretboard radius at bridge is calculated with the stewmac formula)
fretwire crown width
fretwire crown height
action height at nut (distance between bottom of string and fretwire crown top)
action height at last fret
pickup 1 neck position
pickup 2 middle position
pickup 3 bridge position
nut width
the pickup positions should be used to draw circles for the magnet poles on each string so they are perfectly aligned and can be used for the pickup flatwork construction. ideally they would need a rotation control aligning the center line of the pickup so it's somewher between the last fret angle and bridge angle. personally i do this visually depending on the design i'm looking for, some people have huge theories on pickup positioning but personally i don't believe in it.
that should result in everything needed to quickly generate all the necessary construction curves or geometry for nut/fingerboard/frets/pickups. this is the core of what makes a guitar work, the more precise this dynamic system is the better the guitar plays and sounds.
i posted another thread trying to understand how i could use datasets form spreadsheets,databse, csv to organize the input parameters. What would make sense for the strings for example is hook into a spreadsheet with the different string sets, i attached one for the d'Addario NYXL string line which basically covers all combos that make sense.
The string tension is an interesting one, and implmenting it would sure be overkill albeit super interesting to try. it should be possible to extrapolate from the scale length of each string what the tension for a given string gauge of that string would be so that you could say 'i want a fully balanced set' or 'heavy top light bottom) and it would calculate which SKU from d'addario would best match the required tension. All the strings listed in the spreadsheet are available as single strings to buy.
i'm trying to reorganize everything which helps me understand it. i just discovered the 'hidden wires' feature which is great since once i understood what a certain block does or have finished one of my own, i can get the wires out of the way to carry on undistracted. a bit risky to hide so many wires but it makes it so much easier not to get completely lost :-)
btw, the 'fanned fret' term is trademarked, some guy tried to patent it in the 80's which is a bit silly since it has been done for centuries. there is a level of sophistication above this as well, check out http://www.truetemperament.com/ and that really is something else. it really is astounding how superior the tuning is on those wigglefrets, the problem is that it's rather awkward for string bending and also you can't easily recrown or level the frets when they are used. …
e matching with a dedicated component which creates combinations of items. You can find the [Cross Reference] component in the Sets.List panel.
When Grasshopper iterates over lists of items, it will match the first item in list A with the first item in list B. Then the second item in list A with the second item in list B and so on and so forth. Sometimes however you want all items in list A to combine with all items in list B, the [Cross Reference] component allows you to do this.
Here we have two input lists {A,B,C} and {X,Y,Z}. Normally Grasshopper would iterate over these lists and only consider the combinations {A,X}, {B,Y} and {C,Z}. There are however six more combinations that are not typically considered, to wit: {A,Y}, {A,Z}, {B,X}, {B,Z}, {C,X} and {C,Y}. As you can see the output of the [Cross Reference] component is such that all nine permutations are indeed present.
We can denote the behaviour of data cross referencing using a table. The rows represent the first list of items, the columns the second. If we create all possible permutations, the table will have a dot in every single cell, as every cell represents a unique combination of two source list indices:
Sometimes however you don't want all possible permutations. Sometimes you wish to exclude certain areas because they would result in meaningless or invalid computations. A common exclusion principle is to ignore all cells that are on the diagonal of the table. The image above shows a 'holistic' matching, whereas the 'diagonal' option (available from the [Cross Reference] component menu) has gaps for {0,0}, {1,1}, {2,2} and {3,3}:
If we apply this to our {A,B,C}, {X,Y,Z} example, we should expect to not see the combinations for {A,X}, {B,Y} and {C,Z}:
The rule that is applied to 'diagonal' matching is: "Skip all permutations where all items have the same list index". 'Coincident' matching is the same as 'diagonal' matching in the case of two input lists which is why I won't show an example of it here (since we are only dealing with 2-list examples), but the rule is subtly different: "Skip all permutations where any two items have the same list index".
The four remaining matching algorithms are all variations on the same theme. 'Lower triangle' matching applies the rule: "Skip all permutations where the index of an item is less than the index of the item in the next list", resulting in an empty triangle but with items on the diagonal.
'Lower triangle (strict)' matching goes one step further and also eliminates the items on the diagonal:
'Upper Triangle' and 'Upper Triangle (strict)' are mirror images of the previous two algorithms, resulting in empty triangles on the other side of the diagonal line:
…
radiance parameters to get rid of blotching. To add another level of complexity to my problem, I am running simulations with a translucent material with the following properties: void trans testTrans
0
0
7 0.478 0.478 0.478 0.000 0.010 0.178 0.635
I have had no issues with the renderings when I use clear glazing, as seen on this image:
However the blotching-issue becomes very noticeable when I introduce translucent glazing into the scene:
For the two above cases I used the following parameters:
_av_ is set to 0
xScale is set to 2
_ab_ is set to 6
_dc_ is set to 0.5
_aa_ is set to 0.2
_ad_ is set to 2048
_st_ is set to 0.5
yScale is set to 2
_ps_ is set to 4
_ar_ is set to 64
_as_ is set to 2048
_ds_ is set to 0.25
_pt_ is set to 0.1
_dr_ is set to 1
_pj_ is set to 0.9
_dp_ is set to 256
_dt_ is set to 0.25
_lr_ is set to 6
_dj_ is set to 0.5
_lw_ is set to 0.01
I ran another test with increased Radiance parameters and got the following output:
with the following parameters:
_av_ is set to 0
xScale is set to 6
_ab_ is set to 6
_dc_ is set to 0.75
_aa_ is set to 0.1
_ad_ is set to 4096
_st_ is set to 0.15
yScale is set to 6
_ps_ is set to 2
_ar_ is set to 128
_as_ is set to 4096
_ds_ is set to 0.05
_pt_ is set to 0.05
_dr_ is set to 3
_pj_ is set to 0.9
_dp_ is set to 512
_dt_ is set to 0.15
_lr_ is set to 8
_dj_ is set to 0.7
_lw_ is set to 0.005
Although the second blotching case is much better than the first, it is still very bad for hours when the sun is lower in the sky. The above images are rendered for a clear sky at 18:00 in Germany in a West-facing room.
Sorry for the long post! Can someone help? Kind regards, Örn
…
lla progettazione parametrica e le tecniche di modellazione algoritmica per la generazione di forme complesse
___________________________________________________________________________________
luogo:
Sala meeting Hotel Mercure Milano Centro Piazza Oberdan 12 – 20129 MILANO
Scadenza iscrizioni: 12 Novembre 2011 – ore 15.00
___________________________________________________________________________________
info e prenotazioni:
Le Penseur (coordinamento formazione)
info@lepenseur.it
081 564 21 84
347 548 71 78
quote di partecipazione e programma (formato PDF)
ulteriori informazioni sui corsi PLUG > IT
___________________________________________________________________________________
PROGRAMMA DEL CORSO
GIORNO_01
10.00 – 10.30: presentazione workshop
10.30 – 11.30: introduzione alla progettazione parametrica: teoria, esempi, casi studio
11.30 – 13.00: Grasshopper: concetti base, logica algoritmica, interfaccia grafica
13.00 – 14.00: break | lunch
14.00 – 16.00: nozioni fondamentali: componenti, connessioni, data flow
16.00 – 18.00: esercitazione
GIORNO_02
10.00 – 12.00: funzioni matematiche e logiche, serie, gestione dei dati
12.00 – 15.00: analisi e definizione di curve e superfici
GIORNO_03
10.00 – 12.00: definizione di griglie e pattern complessi
12.00 – 13.00: trasformazioni geometriche, paneling
13.00 – 14.00: break | lunch
14.00 – 16.00: esercitazione
16.00 – 18.00: attrattori, image sampler
GIORNO_04
10.00 – 13.00: data tree: gestione di dati complessi
13.00 – 14.00: break | lunch
14.00 – 15.00: digital fabrication: teoria ed esempi
15.00 – 18.00: nesting: scomposizione di oggetti tridimensionali in sezioni e posizionamento su piani di taglio per macchine a controllo numerico CNC…