is called TouchOSC (http://www.hexler.net/software/touchosc).
Basically, what TouchOSC does is sends a message over UDP, but it's formatted according to the OSC specification (http://opensoundcontrol.org/spec-1_0). Firefly (and Ghowl) both have UDP/OSC receivers (although they work slightly differently). Basically, you have a sender (your phone) and a receiver (your computer) and the sender has to know the IP address of the receiver and they both have to know which port they want to communicate on. The port can really be any number you want. So, when launching the TouchOSC app, you need to go into the settings and specify the IP address of your computer and the port you want to use. Then, just pick a layout and start moving sliders to send the data. On the Firefly side, just drop a OSC listener component onto the canvas and specify the same port number you put into the app. Then, connect a Timer component to the OSC listener to get it automatically refresh at a given interval. The data should come over as a data tree, and you can extract the header of the message, or the actual value using the standard Data Tree components.
The one thing you may want to know is that some networks will restrict communications over UDP (particularly those at schools, or other institutions). I would recommend starting out using your home router, which hopefully doesn't have these restrictions. If you do want to use it at a school, you may need to create an ad-hoc network and make sure your phone and computer are both on that same network. Other than that, it should be pretty straight forward. Hopefully this gets you started.
Cheers,
Andy…
ructural member. It can only be used as a Veneer / Cladding. You may observe from my sketch that structural member is only a timber frame. Hence we do not need to have a valid bond as long as the brick veneer is tied together with each other and to the timber structural frame behind.
Nevertheless, though i understood the components used in the definition, i only partially understood the logic behind your definition i.e. only until 'Divide Dist' and Extracting the points. After that I did not understand the logic behind using
a) Extracting 40 random values and than using those values as input for Seed to extract another set of 40 random values.
b) Extracting list length, subtracting with random values created in (a) above and then dividing with number 3.
c) Duplicating the Datas
d) The most perplexing is using above logic (a,b,c) to to extract number of branches (number-40) by using Tree Statistics. If number 40 is the input we required for 3rd Random component Why couldn't we connect the List Lenght to Pramviewer and extract the number of branches (40) and connect the output to the Random Component?
e) Finally i did understand the logic behind creating 2 Vector to create the bricks. But i did not understand the addition following the vector.
f) Why do you use the function 'simplify'? - what does it do? I know it simplifies the data tree, but what does simplifying a a data tree do to the entire definition?
Hannes, i know this is quite comprehensive list of doubt, but your help is and will be always appreciated.
Cheers
AB
…
ceros.
Public concerné /
Architectes et designers, utilisateurs de Rhino souhaitant paramétrer Rhinocéros à l’aide de Grasshopper,
programme associant des composants et une structure de graphe interagissants avec le modèle Rhino.
Une bonne connaissance de Rhinocéros est nécessaire. La langue de la formation est le français.
Structure et Objectif de la formation /
La formation se déroule sur 3 jours : les 2 premières journées sont consacrées aux « fondamentaux » de
Grasshopper avec en préambule une introduction au design et à l’architecture paramétrique et leurs impacts
dans la conception, la création et la construction.
La troisième journée sous forme d’atelier est dédiée à l’étude de cas concrets proposés par les stagiaires, qui,
quelques jours avant la formation, pourront envoyer leurs projets par mail à - info AT rhinoforyou DOT com -
Les stagiaires, après la formation, pourront rester en contact avec les formateurs de HDA par le biais du
blog complexitys.com et le twitter @HDA_Paris. La durée de cette formation permettra d’atteindre une
autonomie et une bonne compréhension basée sur des exemples concrets.
Programme ind icatif des notions traitéES pendan t la formation /
Introduction à la conception Paramétrique . Rhinoscript, Grasshopper: différences et similarités . Interface
graphique de Grasshopper . Objets, Données, Listes . Opérateurs scalaires : La mathématique de
Grasshopper . Gestions des données : la logique de Grasshopper . Vecteurs, Points, Lignes, Surfaces : La
géométrie de Grasshopper . Listes, Arbres, Branches . Le dessin paramétrique: exercices divers et exemples
. Références, Bibliographie, Support de cours . Ateliers d’architecture et design paramétrique (3ème jour) .
Moda lité de la formation /
Venir avec un PC portable équipé de Rhinocéros version 4.0 SR 7 et de la dernière version du plug-in
Grasshopper (téléchargeable sur www.grasshopper3d.com).
Le coût du stage de 3 jours est de 1050 € HT par personne.
Réserver votre place dès que possible car les places sont limitées à 10 participants maximum.
Inscriptions et renseignements: Jacques Hababou, info AT rhinoforyou DOT com
Pour en savoir plus sur l’architecture paramétrique: www.complexitys.com…
io, alle ore 19:30 presso la Mediateca MARTE di Cava de’ Tirreni (Sa), la lecture magistralis dell’arch. Walter Nicolino dal titolo “Augmented visions / Responsive spaces”, un viaggio culturale che, attraversando gli studi progettuali a diverse scale condotti tra la sede torinese e il centro ricerca di Boston, mette in luce una attitudine nell’indagare e nel dar forma alle interazioni tra le persone, gli oggetti e gli spazi, al fine di fornire possibili risposte alle nuove istanze poste dalla rivoluzione digitale.
In apertura i saluti istituzionali del sindaco Marco Galdi, mentre a introdurre la lecture l’arch. Amleto Picerno, promotore del Mediterranean FabLab di Cava de’ Tirreni e tutor della Summer School digitalMed, il laboratorio progettuale che da quattro anni a questa parte, indaga temi, pratiche e tecniche dell’attuale panorama architettonico internazionale. È la smart city al centro della IV edizione di Summer School Digitalmed 2013, che si svolge a Salerno dal 22 al 28 luglio con l’obiettivo di creare un sistema di relazioni e di interazioni continue tra la città, le persone e l’ambiente in cui queste si rapportano in un continuo scambio di informazioni.
Ad esprimere la critic ai prototipi di progetto che emergeranno dal workshop digitalMed, sarà proprio Walter Nicolino, architetto di spicco del panorama italiano, coinvolto in numerosi progetti di ricerca al Senseable City Lab del MIT di Boston, insieme all’arch. Carlo Ratti con cui è fondatore e socio dello studio torinese CARLORATTIASSOCIATI.
Il 26 luglio lo space 1.0 della Mediateca MARTE di Cava de’ Tirreni si fa, dunque, arena d’avanguardia per un interessante dibattito durante il quale, a proposito della Summer School digitalMed, si ragionerà anche sul modo in cui le tecnologie digitali influenzano l’architettura.
«Da qualche tempo a questa parte possiamo scegliere se orientarci alla perfezione tramite navigatori GPS o perderci come sognanti flâneur metropolitani; possiamo associare in un batter d'occhio infiniti layers di dati a un luogo, oppure contemplarne in silenzio il paesaggio; possiamo anticipare la realtà con sofisticate rappresentazioni virtuali, oppure esercitarci in giocose autocostruzioni partecipate.
Possiamo avere l'una e l'altra cosa: non si tratta di una scelta tra il mondo reale e quello virtuale, come predetto da parte della letteratura agli albori dell’era digitale, ma si tratta di capire come il nostro ambiente costruito e gli spazi in cui viviamo stiano imparando a parlare un nuovo linguaggio e ad interagire in modo sempre maggiore con le persone - afferma Walter Nicolino che parafrasando Le Corbusier “La civilisation digitale cherche et trouvera son expression architecturale”, sottolinea l’importanza di integrare le nuove tecnologie e radici locali senza perdere la visione e la dimensione umana della città: All’architettura è richiesta una revisione dei propri strumenti per creare spazi flessibili, inclusivi, in grado di adattarsi ai nuovi modi di vivere e lavorare e di rispondere in modo interattivo alle nostre esigenze».
…
ppresentazione di modelli per l’architettura ed il design, verso un apprendimento d' alto livello delle tecniche di modellazione parametrica 3D.
Il corso si svolgerà nei seguenti giorni:
Sabato 19/10 dalle 10.00 alle 19.00
Domenica 20/10 dalle 10.00 alle 19.00
Scadenza preiscrizione: 16/10
Contenuti
Durante questo corso, attraverso l' uso di tecniche avanzate di modellazione Nurbs,
si potranno costruire modelli tridimensionali complessi che permetteranno di comprendere le tematiche legate alle forme complesse dell’architettura.
Particolare attenzione verrà data allo studio delle superfici a doppia curvatura, alle superfici rigate e alle superfici sviluppabili, quest’ultime adatte alla creazione di manufatti rivolti alla produzione. Allo studio delle superfici sarà affiancata la logica della loro tassellazione, quindi il passaggio da entità continue ad entità discrete, indagandone il valore attraverso esercitazioni pratiche.
Per comprendere meglio le finalità pratiche della tassellazione verrà adoperata una plug-in integrativa specifica per questo tipo di operazione: Paneling Tools. Le lezioni pratiche saranno arricchite da brevi comunicazioni teoriche utili a perseguire l’obiettivo della costruzione di modelli complessi. Sintesi programma
Costruzione di superfici free-form facilmente editabili attraverso tecniche di sculpting ed una gabbia adeguata di punti di controllo;
Presentazione e spiegazione delle superfici a doppia curvatura, rigate, sviluppabili e loro pannellizzazione attraverso elementi lineari o tasselli piani;
Studio della tassellazione attraverso la plug-in Paneling Tools per lo sviluppo di tasselli tridimensionali complessi;
Modellazione di un'architettura complessa, costruita avvalendosi della anche della tecnica del morphing.
Preparazione della mesh e del file per il rendering.
Alla fine del corso, verrà rilasciato l’attestato di partecipazione ad un corso di Rhinoceros qualificato e certificato dalla casa sviluppatrice McNeel, valido anche per la richiesta di crediti formativi universitari.
Docente del corso
Il corso è tenuto da un docente qualificato, con riconosciuta esperienza universitaria, esperto in disegno e rappresentazione dell' architettura e del design ed istruttore McNeel:
Michele Calvano|_architetto, dottore di ricerca in rappresentazione architettonica specializzato nella modellazione matematica (Nurbs) e modellazione parametrica.
Docente ART (Autorized Rhino Trainer) - [vedi CV]
Info
Per ulteriori informazioni di carattere didattico sono a disposizione i seguenti contatti: Responsabile didattico: arch. Michele Calvano
Info mail: parametricart@gmail.com
cell: 340 3476330
…
ur setup. Can you say what sensor you are using? Are you using an Arduino to write this ascii information to the serial port? If so, there may be some formatting code for the string that you'll need to do to get the Read component to function properly. I see that you were able to open the port and Start reading... so my first thought is that the data is formatted correctly....
All of the read components look for a specific character (in this case two characters) to indicate when it has reached the end of the line being read and should spit out the data. In this case, Firefly uses the Carriage Return (\r) and Line Feed (\n) to know when it has reached the end of the line. In arduino, these are automatically added to any line if you use the Serial.println("blah, blah, blah"); command. Notice, this is different from the Serial.print("nothing to see here"); command. This doesn't mean that you can't still use the regular print command... it's just you need to use the println command to indicate when you've reached the end of the line. Let's take a look at a simple example.
void setup() { Serial.begin(9600);}void loop() { int sensorValue = analogRead(A0); Serial.print("The value of the sensor is: "); Serial.println(sensorValue);
delay(20); // important to wait some small time so you aren't sending just a ton of info over to GH which will cause it to crash :(
}
The first print statement prints a string to the serial port... and the next one adds the current sensor value... and THEN adds the carriage return and line feed to start a new line. The nice thing about using these together is that you can concatenate any type of data you want. If you were to upload this sketch, you should see a sentence being printed to the serial port that says "The value of the sensor is: 512". I made up the number, but you get the idea. Notice, I also had to include a delay function. You don't always need this (there are other ways to go about this) but the important thing to note is that the loop cycle on the Arduino can run really fast. I mean... really fast. So, you wont want to send so much data over to GH, because this could flood the string buffer in the Read component and cause it to crash (eventually). It's a good idea to add some small time interval just to slow it down a bit. I should say that I've optimized the refresh rate in the next release so it's significantly faster... so hopefully this wont be as big of a problem... but hopefully that helps some.
Now... Why are you writing data to a sensor? Sensors by default are considered inputs... so I'm quite confused as to why you would want to send data back (if you are... then you need some way to handle the string data being sent from GH... this is the whole reason we built the Firefly firmata... it sets up the two-way protocol so you don't have to deal with all of that mess... If you're going to read and write, you're better off just uploading the firmata and using the Uno Read and Write components). Also, I'm not very familiar with the Hyperterm or Advanced Serial Port Terminal... but I will say that could get COM conflicts if you're trying to open the port with different tools. Anyway, I hope some of this helps you get up and running.
Cheers,
Andy
…
de geometries, which can easily be adapted to changing design intentions and requirements. The core concept of the software is that the brick unit is the basis for every action performed. Basically, a design is generated through drawing, placing and manipulating individual bricks. BrickDesignoffers different methods to manipulate the individual bricks in order to map patterns on a façade. These methods can be extended ad libitum through an open script interface, which gives access to a number of brick parameters.…
Added by Ayuka Oomura at 3:40am on November 4, 2013
atch Online HD 21st Dec 2017. Yeh Hai Mohabbatein 21st December 2017 Watch Online HD 21st Dec 2017. Yeh Hai Mohabbatein 21st December 2017 - Batameezdil Full EpisodeYeh Hai Mohabbatein 21st December 2017 Watch Online, Today Replay Yeh Hai Mohabbatein 21st December 2017 On Star Plus. Indian Drama Series Yeh Hai Mohabbatein 21 Dec 2017 In Hd Quality Full Part. Yeh Hai Mohabbatein 21st December 2017 Today Replay Recap Youtube Video. Yeh Hai Mohabbatein 21st ...Yeh Hai Mohabbatein 21st December 2017 Full Episode 1355 - VideoVideo watch online Yeh Hai Mohabbatein 21st December 2017 full Episode 1355 of Star Plus drama serial Yeh Hai Mohabbatein complete show episodes.Yeh Hai Mohabbatein 21st December 2017 DEC 21 2017 LIVE WATCH NOW ...- Yeh Hai Mohabbatein 21st December 2017 Full Episode Watch Online Dec 21 …Yeh Hai Mohabbatein 21st December 2017 Full Episode Colors Tv HD. Hotstar Yeh Hai Mohabbatein Episode full by Colors Tv.Watch Yeh Hai Mohabbatein 21st December 2017 Video Online.Yeh Hai Mohabbatein 21st ...Watch Ye Hai Mohabbatein Full Episodes Online, Streaming ... - HotstarWatch Ye Hai Mohabbatein latest & full episodes online on hotstar. Upgrade to premium membership to enjoy all the latest award winning Undefined TV shows instantly & ad-free in HD on hotstar!…
eaningful. Humans must interact with it. Information arises when humans examine the data. Knowledge is created when information is transformed through human social interactions.”
Richard Gayle via spacecollective
The space in which we live can be monitored in many aspects and appears to be to be a gradient of data in continuous evolution and change. One of the major advantages of parametric tools is to be able to inform the design processes with accurate, specific and variable, in space and time, data streams .
DATA BODIES is a Grasshopper workshop that will focus on how its nature as an information processor and how it can be (ab)used in order to manipulate data, streaming inputs from various sources and use datafeeds to inform geometry or data structures from the very simple up to more complex ones. The aim is to give an understanding of information and data articultion as already a spatial and architectural operation; results may range from pure data communication protocols, dataviz or data-driven geometries depending on the skill levels and aspirations of each participant. The brief is also open to the suggestions and opportunities that may rise during the workflow.
DETAILS: http://www.superbelleville.org/dataworkshop/…