as passing this extra check and because of that it was running faster. It doesn't mean that the first analysis is totally wrong as it depends on the analysis case and should be checked and optimized before running the final analysis.
You can read more about radiance parameters here (http://radsite.lbl.gov/radiance/refer/Notes/rpict_options.html), and here (http://radiance-online.org/community/workshops/2011-berkeley-ca/pre...). Since you have a light-shelf I suggest you to add to the number of ambient bounces (ab).
Now back to your wish to have the analysis run faster you can comment the line hb_writeRADAUX.checkInputParametersForGridBasedAnalysis() inside Honeybee_runDaylightSimulation and it won't overwrite the initial values but make sure that you run a number of test cases and compare the results between the runs.
Back to your definition, it looks good to me. You could have saved yourself some time by using MassToZone component and then just adding the ceiling separately but there's nothing wrong with your approach.
The main place in the definition that can change is how you're generating the vertical fins. I imagine you can use a single set of components to generate every group of the fins but again your definition will work.
I updated your file to the latest version, which means you also need to update Honeybee and Ladybug in case you're looking to modify the file.
Hope it helps,
Mostapha…
ace when I start running Galapagos/Octopus (below is "room orientation optimization" shared at http://hydrashare.github.io/hydra/viewer?owner=mostaphaRoudsari&fork=hydra_1&id=Room_Orientation_Optimization&slide=0&scale=1&offset=0,0) It may take quite some time to see some results. That's fine for the above simulation. But my real challenge is, when I am going to optimize room dimension with respect to ASE and sDA calculations, either Galapagos or Octopus goes wildly and never come up with a solution. I believe the time-consuming calculation, especially sDA with higher -ab numbers, trigger the lag a lot? Any suggestion/trick to improve it?
Most importantly, based on your experience, for example to optimize window/exterior shades sizes and achieve ASE<10% and sDA>55% (LEED v.4 requirements), Octopus (due to its capacity of multiple objectives) is the only choice? Any other approaches within grasshopper?
The alternative approach in my mind as a GH beginner is as follows. But I am not sure whether it is doable. Again, your comments will be greatly appreciated.
Since all my room/window/shades dimension are controlled by number sliders, I am thinking whether a component from GH will trigger these number sliders (not necessary to be all of them but one by one) automatically. If this is possible, I can do "data recorder" to record outputs from ASE and sDA. Eventually I will have a database of the input parameters and sDA/ASE results.
Does it make sense? Is there a component which can trigger number slider output at certain step?
Many thank!
Cheney …
s levels of detail by subdividing a 6 sided cube mesh and projecting its vertices according to a referenced height map. This is one of the standard conventions for building full sizes planets. At the lowest level (0) the mesh planet is made of 6 pieces(each 32x32 resolution). The next level down (1) is made of 24 pieces... 6 divided by 4 = 24. Level (2) is 96 quads etc etc. The script will generate each quad at its sub-division level and compare edge vertices to neighboring quads. It will then make sure any shared vertices are in fact at the same projected vector. This ensures a planet quad with edge vertices that match.
The problems comes in texturing each quad.
If I build the quad as a nurb surface from points I can place the texture easily because each surface UV maps squarely to my texture map (which is also square).
If I build the quad as a mesh I cannot just apply the square texture to the mesh UVs. This is because when you unwrap the UVs from a mesh they will not unwrap like a nurb surface's UVs. Therefore to get the correct mapping I would have to manipulate each UV back to an evenly aligned array (which is 1024 points in a 32x32 resolution UV). Maya and blender have 'relax uv' and 'align UV' functions but they don't do the trick and manual corrections are out of the question. So why not skip the mesh method and use the nurb method?
I did this and there is a trade off. The nurb will accept the material texture I want with no other work on my end but when I export the object as an .obj rhino creates its own mesh to describe the nurb(with various unsatisfactory setting options). This works great up to a point because at some level the interpreted mesh will have vertices that do no match at the edges, ie .. creating visible seams in the mesh. The picture below is the nearly seamless planet at LOD(1) made of 24 quads, each with 32x32 vertice resolution and a 512x512 jpg texture running in Unity3d 5. It works but at close level there are seams. This will be resolved simply by having the next LOD(x) instantiate before getting close enough to see the seam but at core nerd level I want the seamless mesh.
So, I can make the seamless mesh but I can not realistically texture map it. I can also make the nurb surface from points and texture it at the expense of the edge vertices matching. I am at the split in the road but I want to have my cake and eat it too. Thoughts, comments, trolls...?
Thanks for reading =)
Footnote: For you pros I am not using seamless noise across the map I am using grasshopper to sew up my otherwise non perfect edges.
Other programs in the pipeline:
-WorldMachine 2
-Wilbur
-Photoshop
-Unity3d…
ve Intermediate Insight of Computational Design Strategies While Exploring Rangoli Art form in 2 Dimension and 3Dimesion in which Participants will not only be trained to Digitally Design using Parametric software's but they will also be trained to Fabricate them in reality.
This Course will be explored in manner where Participants will understand inter-dependency of Rhinoceros3D & Grasshoper3D through a unique Hybrid Teaching Method While Exploring Rangoli Geometry .
The course will also take participants through Topics such as - Computational Thinking, - Computational / Parametric Design, - Computational Rangoli Exploration, - Digital Fabrication, - 3D Visualization ( Rhino3D 6), - Making Info-graphics & Design Diagrams ( Rhino3d 6 ).
Participants will also be doing a Project at the last Leg of Workshop in which they will implement the skill they gained in first Few Weeks.
{ Tutor } Nitant Pixelkar (Computational Artist / Designer, Mumbai)
Nitant Hirlekar A.k.a. Pixelkar, is a Computational Artist. He graduated from Rachana Sansad school of Interior Design 2011, Mumbai. In Academics He Bagged Two Gold and One Silver Medal on National Level.
In his post academic days, he came across the Emerging Computational Techniques in Design industry in which Algorithm serves as a main Functional part. He uses Algorithms to Deconstruct the Captured images in Pixelated form using the Grid of the Desired Indian Art Forms.
He Heads Collective Group Named "Mutation Lab” which is a multidisciplinary Design & Art Cell. Where they Explore Computational Approach while Designing Various Scales Spatial Installation, Digital Fabrication, Interactive Installations and Computational Consultancy for Various Architects.
He has exhibited his first artwork in Kalaghoda Arts Festival for in 2014 And further in 2016 and 2017.In 2015 he exhibited in Dharavi Biennale” organized by Wellcome Trust,London & Sneha Organisation, Mumbai Which was internationally acclaimed. In 2016 he got Featured on a TV show - The Creative Indian's as an Absolut Creative Indian of the Week.
Academically he is been involved in Many Computational Design Workshops / Elective Studios for School of Interior Design (Rachna Sansad), LS Raheja College of Architecture & Rat-Lab (Delhi).
{ Participants } The Course is aimed at Architecture, Interior Design, Product Design,Furniture Design & Fashion Design Students and Professionals. However we would be thrilled to have any Interdisciplinary Artist / Creator/ Maker to join the Course as well.
{ Level }
Intermediate
{ Timing } Monday To Friday - 6:00 PM to 9:00 PM (15 Hours/ Week = 5 Week X 15 Hours = 75 Hours )
{ Dates } Registration Ends - 24th April 2020 **Subejct to Availablity
{ Workshop Dates } 4th May 2020 To 5th June 2020
{ Venue } Lower Parel,Mumbai ( Details To Be Announced )
{ Schedule }
{Registration Form}…
(1) I have been exporting small sections of a larger model into Maya from Rhino as FBX. In Maya I rotate and scale the models (-90 in X, Scale XYZ 0.001). The Named Views are being saved, but do not have a successful import into the Maya model. They do not appear as in Rhino, and the problem is not solved by scaling or rotating the cameras.
(2) If I try going the other direction, the cameras exported from Maya as FBX are also not aligning with the model in Rhino as they are in Maya.. I will do my best to post some images of the problem and hope you can help.
error !!
This is what the named views look like
here I am trying to the other way with a good view from Maya
strange placement..
This is the best result I can achieve, after I scale the camera by 1000
Any Advice???
Thanks, Robert.
…
ysim.ning.com/
When you run the simualtion you will notice on the batch terminal that Daysim is also being called, so you may want to consider how Daysim uses Radiance files & data.
Regarding your current problem, I think you stumbled onto something weird and interesting.
Interior and exterior readings appear to differ by 40 in the best case scenarios. Even setting the transmittance to 1 yields similar results. I tried changing from cummulative sky to climate sky and got similar values. Changing the test points did nothing either.
I think, (yet I'm too lazy to prove this) that the difference in values stems from diffuse radiation over the sky dome.
If you delete everything except the glass you'll notice that interior values are like 80-90% of the exterior values (this seems like the expected behaviour with a transmittance of 1). So, if we consider that a vertical window, part of an opaque box, is receiving radiation from 25% of a sphere, as you start to inset the interior test points the radiation they receive will be a fraction of the 25%.
Let me try to explain this better...The exterior surface receives radiation from a section of a sphere calculated by 180degrees on the xy plane (let’s call this angle theta) and by 90degrees (let’s call this angle phi) in azimuthal elevation. If you integrate this over spherical coordinates (theta from 0 to pi; phi from 0 to pi/2) you will find that it comes to a quarter of a sphere. By comparison, the interior surface will not integrate theta from 0 to 180degrees,nor phi from 0 to 90degrees, instead it will be the subtended angle from the exterior surface as a function of their separation; the farther in you go the smaller the view of the outside.
If my hypothesis is correct there shouldn't be that much difference since the separation is only 10cms...the subtended angle would be like 170 instead of 180 for theta and 85 instead of 90 for phi...overall if you integrate both spherical areas there should only by a difference of 10%.
In conclusion, I believe the unexpected behaviour stems from the previous subtended angle thing. If direct radiation was the only factor the difference would be the aforementioned 10%, which suggests that an additional source of energy is also affected by this. Perhaps indirect and diffuse radiation from other areas of the sky dome.
I’m definitely intrigued on why this is happening. Please post if you figure it out.
Regards,
Mauricio
…
he time to work with it.
the project is about facade strips which turns along height. the top angle is
parallel to the facade and the bottom is max. 90 degrees twisted, but the strips
should turn diffrently to achieve more dinamic look.
first i have tried to achieve this by calculating distance between the rotation angle from points of the grid and a single point.
then i have tried to ad some more effecting points and used the distance to the divided surface (the circles are just to control the area of effection):
i manually lofted it.
the result is a bit annoying becouse the points that effect the angle are always visible:
i have triend to solve this by drawing a line and divided it to recieve points along the bottom of the geometry. the result is not working properly:
Anyway,
there must be a better/smoother way to achieve this. i would like to effect the twist of the surfaces by distance to a spline, but im just lost. can you help me please?
the problems im encountering:
0- distance spline to grid to effect the angle
1- list of x/y coordinates and angle of rotation for each point of the grid
2- export points to excel
3- lofting lines in one direction only (x1, x2, x3...)
4- reduce the list data to 2 decimal (0,00)
5- maybe angle from radian to degrees
thx…
te some cut sheets, but not to optmize material, rather define some cut lines. Everything that I am cutting is made of planar wood elements, but there are very specific geometries (mostly straight lines) and I have to put tolerances and radiasas at the corners in order to cut on the cnc mill. Spending time to figure out how to automate is necessary, but I am stuck!
One thing the definition is doing is taking my brep modeled components in rhino and makking them into 2d close curves and laying them side by side. It works...not ideal as its not layed out in a sheet, but that is not the most important part.
Another particular problem is that you will see some notches in the curves, which other pieces will slip into, so different slots need different specific offsets (making them larger) as a toelrance to allow for material play. This I don't even know how to set up so maybe it will just have to wait.
THE MAIN QUESTION, and super important would be, LIFESAVER:
At all 'inward' corners...which I think will always mean concave corners (most are 90 degrees, but are within to sides, instead of a corner sticking out). I'm sure its obviousy, but the reason being the outward corners a circular dril bit can cut, but inward ones need an arc profile extended beyond where the corner of the other piece will fit into. The drill bit i am using is 6mm, so 6mm diamters arcs is what i'm working with.
I have managed to put such an arc at every vertices of each cut piece. The problem being some stick outward isntead of cutting into the piece. So each one needs to be orieneted correctly. Ideally they would also only draw into inward corners, but I can always delete them out. I think maybe I am missing a more logical mathematical way of defining?
For these geometries it is not very important which side the half circle arc in on in the inward corners, but I also have some geometries that I will have to control where the circles face according to the rest of the cut piece.
The cutouts in the middle of the pieces that are curves do not need such corners obviously.
The picture is an example drawn
I hope this isn't too specific and long. in general though automating fabrication, and controling pracitcal math and orientation problems like this is itnersting to me!
THANKS…
perienced with grasshopper, but so far I've managed to combine the following:
Giulio Piacentino's "Catenary arch from height" script
Pirouz Nourian's "Mobius" script (Obtained from a friend)
End Result:
Here's where I'm stuck: I want the mobius twist to revolve around the midpoint of the arch, but the script uses the input values to determine the endpoints, resulting in a weird sinuous shape when viewed from above. Also, the secondary end points (generated by the mobius script, determining the width of the surface) are generated by default along the z axis, resulting in an arch that only touches the "ground" at two points. I attempted to work around this issue by trying to force the zHeight parameter to correspond with the y axis (thus rotating the arch 90 degrees so it would lay "flat"), but the script interprets the third point as a value and not as an actual point to bisect. I thought this might be an issue with the C# component that I obtained from Giulio Piacentino's script, so I attempted to tinker around with the source code. Unfortunately, I'm not fluent in C# so I only managed to mess everything up (I've since recovered the code from the cache). Anybody got some ideas? -BC …
next level.
This Parametric Design course will provide the participants with the necessary knowledge and ability to use Grasshopper, a free visual programming plugin in Rhinoceros; you will be guided through a series of hands-on exercises that highlight NURBS modeling and its concepts. We will introduce Grasshopper as a graphical algorithm editor tightly integrated with Rhino’s 3D modeling tools. You will also learn how Rhino is used to render models for visualization, translate 3D models for prototyping, and export 3D models into 2D CAD or graphics programs.
English is the course main language.
Location: Düsseldorf city center
Registration and buying Tickets
www.digitalparametrics.eventbrite.de
Course Calendar:
4 Days 6 hours each
Total duration 24h
2 weekends
Date:
Sat. 17 - Sun. 18 June
Sat. 24 - Sun. 25 June
10:00 - 17:00
Getting Started in Rhino. 2 days (17 - 18 June)
Getting Started in Grasshopper. 2 days (24 - 25 June)
-----------------------------------------------------------------------
Participants will be given a certificate of participation at the end of the course.
-----------------------------------------------------------------------
Course fees:
Professionals: 600€ (excl. MwSt.) Students: 500€ (excl. MwSt.) Students need to provide: Copy of current student ID or proof of student enrollment at University/School.
Group discounts:
Group of 3 professionals: 3x500 = 1500€ (excl. MwSt.)
Group of 3 Students: 3x400 = 1200€ (excl. MwSt.)
Participants are kindly asked to bring their own laptops and have pre-installed Rhino + Grasshopper.
Useful Resources:
Rhinoceros Installation (90 days full version trial available): http://www.rhino3d.com/download
Rhinoceros for Mac (includes Grasshopper) http://www.rhino3d.com/download/rhino-for-mac/5/wip
Grasshopper Free Installation: http://www.grasshopper3d.com/page/download-1
Grasshopper Free Plugins: http://www.food4rhino.com/app/lunchbox http://www.giuliopiacentino.com/weaverbird
Main Tutor:
Rihan
M.A. Dipl.Ing. Architect
Architect at RKW Architektur + Düsseldorf
For any questions about the course, please email: info@immersive-studio.com…