to select a period of time across the year, for example, every hour from January 1 to June 30.
I currently use DOY/HOY to assign the analysis period (basically I want to run 8760 hours), and connect its HOY to DAY_MONTH_HOUR_CALCULATOR. Then, connect it to CB sky. But, there are several warnings pop-up on the component "DOY/HOY", says Feb. has 28 days, the date is corrected by Ladybug, and as well as other months less than 31 days. After the HOY is connected to the "DAY_MONTH_HOUR_CALCULATOR", the warnings are gone, and the lines become green. However, when I connect the "DAY_MONTH_HOUR_CALCULATOR" to CB sky, the output of "sky file pate" turns orange again. This causes the repetition of the last day of those months less than 31 days.
(I attach a picture for your information)
Does any of you know how to solve this problem? And what is the best way to run annual hourly (8760 hours) with CB sky?
Many thanks in advance!!
Wenhsin…
NONE, in SIZING:PARAMETERS". I'm not sure of where to start in troubleshooting this. I've attached the file.
Thank you,
See the errors and warnings below:
{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. [1 of 8] Writing simulation parameters...
3. [2 of 8] Writing context surfaces...
4. [2 of 8] Writing context surfaces...
5. [3 of 8] Writing geometry...
6. [4 of 8] Writing Electric Load Center - Generator specifications ...
7. [5 of 8] Writing materials and constructions...
8. [6 of 8] Writing schedules...
9. [7 of 8] Writing loads and ideal air system...
10. [8 of 8] Writing outputs...
11. ...
... idf file is successfully written to : R:\Green\SuRG\Building_Performance_Analysis\2016_analysis_studies\Energy_Analysis_Comparison\Honeybee_+_Ladybug\tutorial01\EnergyPlus\tutorial01.idf
12.
13. Analysis is running!...
14. ...
...
Done! Read below for errors and warnings:
15.
16. Program Version,EnergyPlus, Version 8.5.0-c87e61b44b, YMD=2016.10.31 11:39,IDD_Version 8.5.0
17.
18. ************* IDF Context for following error/warning message:
19.
20. ************* Note -- lines truncated at 300 characters, if necessary...
21.
22. ************* 24 Sizing:Parameters,
23.
24. ************* Only last 1 lines before error line shown.....
25.
26. ************* 25 None, !- Heating Sizing Factor
27.
28. ** Severe ** IP: IDF line~25 Invalid Number in Numeric Field#1 (Heating Sizing Factor), value=NONE, in SIZING:PARAMETERS
29.
30. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
31.
32. ** ~~~ ** Possible Invalid Numerics or other problems
33.
34. ** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
35.
36. ...Summary of Errors that led to program termination:
37.
38. ..... Reference severe error count=1
39.
40. ..... Last severe error=IP: IDF line~
, value=NONE, in SIZING:PARAMETERS
41.
42. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
43.
44. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
45.
46. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
47.
48. ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
49.
50. ************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 9.34sec
51.…
o retrieve the first one: (0;0), (0;1) ... (0;4), I put 0 in Path and the TreeBranch turns red. What am I doing wrong?
I would really appreciate some help!
Thankyou!…
Added by Tina Jerrera at 8:09am on November 25, 2016
vas
Closing and creating a new file (memory resets when this is done) @4:00, 5:57, 6:53
System slow down and crashes @ 8:16 (takes 5 minutes to end the process - perhaps not the most entertaining movie to watch until the end - a good point to turn the kettle on)…
he installation folder, Drag & drop SYNTACTIC(green one) over your grasshopper canvas.3. Close your rhino and reopen it. 4. Type GrasshopperDeveloperSettings5. Tick the Memory load *.GHA assemblies using COFF byte arrays option6. Run grasshopper and enjoy plugin…
he canvas redrawing and the Rhino viewport redrawing take some time as well (on my system 6 ms for the empty Gh canvas and 28 ms for the empty Rhino viewport). No timer can avoid that, to my knowledge. The trampoline computes timing after the solution is complete. This means that one cycle is: solution completed + drawn + user specified interval.
Hope that this helps to get started,
- Giulio________________giulio@mcneel.com…
heating? Or cooling?)
What if you have 20C? You need to heat to 24-26?
What if you have 28? Then you cool to 24-26?
Something is missing here ...
Or am i wrong? (In this case i don't understand the logic).
Besides that, you are simulating 3 zones instead of 1. Your conncetions of all the HB_setEPZoneSchedules to the HB_setEPIdealAir is causing this. Messy ... a little bit.
-A.…
not rhinocommonPath
(this is not the bug but if the correction is not made, then the form doesn't clearly ask for the dll
Second part of the solution (and here it corrects the bug)
Do something so we do not execute line 53 -if (File.Exists(Path.Combine(path, "rhinocommon.dll")))- if path == null.
The way I did it is certainly not the most elegant one but it's efficient. I have added the two following line of code
if (path == null)
path = "C:\\";
--------------
Now I have also corrected the code so it finds the dll on my computer. But I'm not sure the installation is the same for everyone. On my computer the information GrashopperFinder.cs is looking for is not under the LocalMachine hive but under the CurrentUser hive! So FindGrasshopper (line 19) is never checking for the right hive.
As I'm on a Windows 7 - 64, I have just added at line 28 the following code
SearchRegistryKey(rh5_64_Reg, rh5_RegName, RegistryHive.CurrentUser, RegistryView.Registry64, strings);
Now everything seems to work with the latest version of Grasshopper. So next step is to put the right .NET version and also extend the wizard to Visual Studio Express 2012 or beyond (Already done for the wizard for Rhino, so it shouldn't be an bid problem).
Anyways, thank you if someone who know how to code can double check what I did and correct everything (i.e. put the right code on GitHub + the corrected template on the VisualStudioGallery
Regards
Serge…