Angeles, which has 12% of the year made comfortable, and Shiraz, Iran, which also has 12% comfortable (assuming default parameters).
Jerusalem also makes sense to me. There is only a maximum possible 9% of the year that is inside the polygon (you'll see this if you set the timeConstant to a very high number). The default strategyPar makes 6% of these hours comfortable and 3% without cool enough temperatures in the previous hours. This seems reasonable to me.
I could be convinced to change the default time constant to 12 hours (instead of 8) as I know that 12 is the default of climate consultant but that seemed really idealized in my opinion. You'll need really high exposed mass and insulation without much internal heat gain to make conditions stable for more than 8 hours in my opinion.
As for the solarHeatCapacity, I get changes when I drop it down to 10 W/m2 or boost it up to 100 W/m2. It's definitely a parameter that operates on an "order of magnitude" scale and little tweaks to it won't change it too much. You can think of this number as representative of a lot of other physical properties: most notably the depth of the space being passively heated and the thermal mass of that space's materials that participate in heat exchange over the time constant. Climate consultant uses a default assumption of 30 W/m2 but, from my calculations, this is likely assuming a space that has a facade to floor area ratio that is greater than 1. If we say that we need to raise the temperature of 10 cm of an exposed concrete floor for passive heating purposes, and we have a facade-to-floor area ratio of 1:
Required solar flux = ((1 facade-to-floor ratio) x (0.1 m3 of concrete) x (2400 kg/m3 concrete density) x (880 J/kg-K concrete specific heat capacity)) / 3600 seconds/hour
This lands you with a required solar flux of 58 W, which is almost twice the 30 W climate consultant default. While me might say that not all 10 cm of concrete participates over the course of a default 8-hour time constant (most of the action is probably within the first 5 cm), we also have to account for things like transmittance of solar though the window, which, for triple pane, is probably only half of the incident solar. So 50 W seemed to be a more reasonable rule of thumb from my perspective, essentially assuming a facade-to-floor ratio of roughly 1 with 5 cm of concrete participating in an 8 hour heat exchange and a little more than half of solar heat getting through a fully glazed window.
Let me know if that makes sense or if you have any suggestions,
-Chris…
onstrates the following:
1. The definition's functionality employing HumanUI for the custom user interface.
2. Color based segmentation in manual and auto modes.
3. The evaluation of the definition's ability to handle different point cloud data sets.
This definition performs color based segmentation in two modes.
A manual mode, that implements the Delta-E CIE 2000 color difference formula, for targeted feature detection. An auto mode, that employs a simple RGB Color Range algorithm for quicker preliminary results.
RGB to XYZ to CIELab conversion and Delta-E scripts were based on Colormine's project code from github. Results have been compared and verified with the results of http://colormine.org/color-converter and http://colormine.org/delta-e-calculator/Cie2000.
Each stored class is charted and can be accessed through the UI, as shown at 2:30, where Delta-E CIE 2000, in CieLab color space, output results were found to be in perceptive conformity with human eyes, far superior to the preliminary RGB implementation.
Initial definition versions could process highly subsampled clouds in acceptable timings. Further research showed that employing the multithread processing of Volvox components, bundling the Delta E formula with the RGB to CIE lab color conversion script, per color segmentation calculations for a one million points point cloud would go down from 23 (c# script component) and 8 (vb script component) seconds to approx. 1 second (volvox script cloud component), thus allowing the segmentation of less subsampled point clouds.
I would like to thank Heumann A. and Zwierzycki M. who provided direct support with HumanUI and Volvox. Also Grasshopper3d forum users Maher S. and Segeren P., who contributed with Rhino viewport manipulation scripts.
More on Volvox:
http://papers.cumincad.org/cgi-bin/works/Show?_id=ecaade2016_171&sort=DEFAULT&search=ecaade%20volvox&hits=2629
http://www.food4rhino.com/app/volvox
http://duraark.eu/
HumanUI:
http://www.food4rhino.com/app/human-ui?page=1&ufh=&etx=
ColorMine:
https://github.com/THEjoezack/ColorMine…
azione tramite interfaccia grafica 6 ore
Interfaccia Grasshopper
Parametri e Componenti
Operazione di Logica e Matematica
Vettori
Case study: concetto base di attrattore
Gestione data matching
Primi approcci alla modellazione parametrica – 4 ore
Trasformazioni di base (sposta ruota scala orienta)
Strumenti di Morphing
Utilizzo di Sweep e Loft e di altri strumenti di creazione superfici già noti da Rhinoceros
Esercitazione pratica: creazione del modello concettuale della Serpentine Gallery - B.I.G.
Focus sulla gestione dei dati - 4 ore
Creazione e gestione delle liste
Studio del data tree
Esercitazione pratica: creazione di un soffitto cassettonato
Creazione di geometrie tramite mesh – 6 ore
Utilizzo degli algoritmi di Delaunay
Utilizzo del Facet Dome
Utilizzo del Substrate
Utilizzo degli algoritmi di Voronoi
Esercitazione pratica: creazione di un gazebo attraverso l’uso di pattern
Creazione di ‘paneling’ di superfici curve – 6 ore
Discretizzazione di una superficie a doppia curvatura tramite pannelli piani
Strumenti analisi superfici
Visualizzazione superfici tramite falsi colori
Esercitazione pratica: creazione di una facciata interattiva
Digital Fabrication e messa in tavola – 6 ore
Interoperabilità tra Grasshopper e altri applicativi
Creazione di Truss parametrica
Gestione dell’abaco dei pezzi
Esercitazione pratica: la Facciata dello Stadio Friuli di Udine - Ipotesi di costruzione e gestione tramita fabbricazione digitale
Requisiti di accesso
Conoscenza delle tematiche CAD di base e dei comandi principali e interfaccia Rhinoceros 5.
Certificazioni
Alla fine del corso verranno rilasciate le certificazioni ufficiali da ART (Authorized Rhinoceros Trainer)
Numero partecipanti
Il corso parte al raggiungimento di un minimo di 4 persone ad un massimo di 8. Ogni partecipante dovrà essere munito di proprio computer con Rhinoceros.
Costo del corso
Il costo del corso è di 600 € + IVA
Sconto di 50,00 € per i giovani che hanno meno di 26 anni.
Ulteriore sconto di 50,00 € Early Bird per tutti coloro che si iscriveranno entro il 5 Settembre 2016
Nel prezzo è compresa l’iscrizione al FabLab Toscana – maggiori informazioni qui
FabLab Toscana
Il FabLab Toscana presenta un insieme di per i propri associati: sarà possibile l’accesso ai laboratori del FabLab (durante i normali orari di apertura), partecipare ai workshops gratuitamente o a prezzi calmierati, l’utilizzo della macchine (seguendo il regolamento interno), …
s, the participants will focus on the key advantages of Grasshopper’s capabilities through a range of design challenges in order to aid designers in both their drafting tasks and modelling capabilities.
The workshop covers many concepts such as Object Attributes/Parameters, Data Types, Data Structures, and Designing with Algorithms. Specifically, this course will focus on understanding both Lists and Data Trees, as well as the best practices for integrating Grasshopper into your Professional Design Workflow. The workshop offers guided curriculum and continuous support, based on in-depth and professional learning experiences.
Workshop outcomes:Teach the participants how to:-
+ be proficient in parametric logics learning the key benefits of parametric techniques in architecture design workflow (when to use it & how to use it)+ Correctly communicate with different 3D and BIM packages in order to keep the geometry clean and light while preserving all NURBS information.+ Develop architecture design based on mathematical equations to create non-standard free form building skin.+ Create a pattern that changes dynamically based on specific inputs which can be applied over the building façade, interior walls or ceiling or even floor pattern.+ Automate and Optimize design variables to achieve the optimum solution for the design problem.
Program Outline:
DAY 1:-Introduction to Parametric Design -Introduction to Grasshopper & Rhino (technical tools).
DAY 2:-Exploring the parametric workflow. -Setup the design algorithm & generating a list of data.
DAY 3:-Introducing the new ways of generating parametric curves and surfaces.-Parametric form generation in-dept
DAY 4:-Introducing Data Tree logic and parametric transformations.-Creating Associative techniques – Attractors (points, curves and vectors).
DAY 5:-Working with advanced form generation with dynamic pattern.-Parametric optimization based on environmental analysis -featuring the Performance-Driven Design possibilities
DURATION:6 – 8 hours per day [50 - 60 hours Total]Every Saturday [9.00 Am : 1.00 Pm & 2.30 Pm : 6.00 Pm]
PREREQUISITES:No need of any specific knowledge of Rhinoceros or Grasshopper.
REGISTRATION:In order to register, you will need to fill the Registration Form .https://docs.google.com/forms/d/1PckdW1hrWs9fJAHWBZlVsuhH8K0PfDuMWIpXHT_4FYw/viewform
REGISTRATION DEADLINE:23th October 2014.…
Added by ayman wagdy at 7:48am on October 19, 2014
imes. Your loop should go to y.Count - 1. Or, you could use a For...Each loop, circumventing the problem altogether:
Dim shortLines As New List(Of Line)
For Each segment As Line in y
If (segment.Length < x) Then
shortLines.Add(segment)
End If
Next
A = shortLines
--------------------------------
Another problem is this line of code:
New_Lines.Add(New_Line)
It is located inside the loop but outside the If statement, meaning it gets run every single iteration. This fills up the short line list with duplicates.
-------------------------------
Here's something else which is redundant:
Dim Input_Line As New Line
Apart from the fact that you don't need a special variable for this at all, you also don't need to add a New keyword. The type Line in RhinoCommon (just like Point3d, Vector3d, Plane, BoundingBox etc. etc.) are Structures, not Classes. Structures always exist when they are defined, whereas Classes can be null ("Nothing" in VB).
-------------------------------
Some more advice:
Dim i As Integer
For i = 0 To y.Count()
You can merge these two lines into one. VB.NET allows you to declare your iteration variable inside the loop:
For i As Integer = 0 To y.Count - 1
--------------------------------
If you don't like the For...Each approach at the top of this answer, here's how to write this using a For...To loop:
Dim shortLines As New List(Of Line)
For i As Integer = 0 To y.Count - 1
If (y(i).Length < x) Then
shortLines.Add(y(i))
End If
Next
A = shortLines
ps. A personal preference of mine is that I always encase the expressions inside If...Then statements in brackets. You technically don't need to do this, but I find it makes the code more readable.
--
David Rutten
david@mcneel.com
Poprad, Slovakia…
on excel (leaving 0,0 cell blank and also making sure there are no commas in the names ) Also let's call the names "ID"
2 - For the weight, use numbers ranging from 1 - 10 where 10 is the highest dependancy.
3 - Save the file as a Unicode CSV from excel
4 - Create another file on excel that has the attributes of your spaces, with the names of your spaces under the header ID (let's start with a simple "area" and "SNo" attribute but you could add more features for sorting and manipulating your data)
5 - Open Gephi and further open your matrix CSV file
5 - Import it as "," (comma delimited file) and make sure you check "matrix" for the data type
6 - Ensure the import is nondirectional as well (or Gephi adds silly arrows)
7 - Not gonna go into the gephi bit too much but select a force atlas layout and set the force to something high 1000 or 10000 depending on the size of the data and the attraction to a 1000th of that 1 or 10. Go to the data lab and import your excel with the attributes and append to your existing datasheet.
8 - Set the node attributes to use the area for the node size and color scheme to SNo
9 - Play around with all the layout options and finally go to your preview. Once you're happy with it, export it to a GDF graph file.
the GDF now has the coordinates of the circles and the diameters. as well as the edge connections.
I've written a very amateur script that converts this to GH geometry (below)
Hope this helps someone out, I'm still figuring out the gephi streaming API but I've only started with python about a month ago so might take a while to get there.
You can use the second half of the GDF files to also create dependency chord diagrams online as shown in the third image.
https://flourish.studio/2018/07/25/how-to-make-a-chord-diagram/
Cheers,
Sanjay
…
le I´m running into now.
I´m trying to make a patern for a screen printed window. The window measures 4,5 x 1,2 meter and had a cirle every 0.5cm, that is 216.000 different circles, generated in GH by Image Sampler.
If I save the rhino file its about 289Mb, which seems a bit large to me, since it only contains those 216.000 circles, and no other geometry. I tried rebuilding but the individual circles are already the most efficient they can be, that is point count 8, degree 2.
If trying to export this file to AutoCAD, while exporting the file crashes. So do any of you guys know how I can either make the GH-file, the Rhino-file or the exporting proces more efficient?
Thanks a lot,
Emiel
p.s. I´ve added the GH-file for reference…
Added by Emiel Tijhuis at 7:38am on October 20, 2011
hole new realm?
This Parametric Design Workshop will provide you with the necessary knowledge and ability to use Grasshopper, a free visual programming plugin in Rhinoceros. The workshop will also include a hands on parametric project.
If you already know Grasshopper and would like to uplift your parametric knowledge, then you can choose option 2.
Option 1: General WEBINAR for Beginners - 16 hours: Start 20.06.2020
Option 2: Intensive WEBINAR for Intermediates - 8 hours: Start 27.06.2020
TIME ZONE: GMT +0200 BERLIN GERMANY TIME
Kindly reserve your Tickets here:
https://billetto.eu/e/parametric-design-webinar-rhino-grasshopper-Tickets-439647/
WEBINAR LINK:
WEBINAR invitation link will be sent to all participants after registration via private Email…
indexsequential philosophy. This stands for a sequential access to data organized in logical records addressed by a key formed by two Integers.
CDBASE may be seen by the programmer as an unlimited number of sequential streams organized in the form of a linked list. Physically CDBASE is formed by a direct access diskfile with fixed record length and a memory buffer to enhance IO-Operations. For parallel access an enhanced version using pvm is available."
"Locking is done via special entries in the database and the possibilities provided by the operating system (lockd / SHARE etc.) The lowest level ensures that writing of directory entries or requesting dataspace is only possible by a single process at the same time.
The next level locks a complete key. If you write to a key you will lock implicitly all records within the key. Other processes may lock other keys at the same time. You may lock a key explicitly by a call, then have to remove the lock explicitly by an other call. The implicit locks created by a writing process is implicitly released by a read from the same process."
As for the initiation, a function returns current status of the database: int sof_cdb_status ( int Index )
the current status of the file with Index is returned
Index Index of DB Returnvalue Stat Bitpattern CD_STAT_AKTIV (1) CDBase is active CD_STAT_OPEN (2) Index is connected to file CD_STAT_SWAP (4) File has ByteSwap CD_STAT_READ (8) File has been read CD_STAT_WRITE (16) File has been written CD_STAT_LOCK (32) File has active locks CD_STAT_PVM (64) File is opened via pvm server
I hope it answers your questions, I am very uncertain in this topic.…
rom a few pieces until all of the pieces are in place. You could also, theoretically, modify the form of the base, high, etc.
To do this I started making three pieces (all triangular) of different sizes... and then I stablished that there is going to be a bigger concentration of bigger pieces on the first third of the building, a bigger concentration of medium pieces on the second third and a bigger concentration of small pieces on the last third. I did this by rotating the pieces a number of times accordingly to a percentage.. the funny thing is that it works most of the times, but it doesn't work if the base of the building has 3, 8, 12, 18 or 20 sides (20 being the higher number on the number slider).. maybe there is a way to solve this with lists that I am not using????
My second problem is that I want to rotate each floor of the building separetly using a range... the thing is, I cannot make it work, because it rotates each triangle and not the whole floor... maybe there is a way of making groups or changing the list definition, but I'm not getting there.... I tried working with planes, but it is even more difficult to make the whole thing work...
I'm attaching the grasshopper documment and a couple of pictures so you can get my idea....…