ace when I start running Galapagos/Octopus (below is "room orientation optimization" shared at http://hydrashare.github.io/hydra/viewer?owner=mostaphaRoudsari&fork=hydra_1&id=Room_Orientation_Optimization&slide=0&scale=1&offset=0,0) It may take quite some time to see some results. That's fine for the above simulation. But my real challenge is, when I am going to optimize room dimension with respect to ASE and sDA calculations, either Galapagos or Octopus goes wildly and never come up with a solution. I believe the time-consuming calculation, especially sDA with higher -ab numbers, trigger the lag a lot? Any suggestion/trick to improve it?
Most importantly, based on your experience, for example to optimize window/exterior shades sizes and achieve ASE<10% and sDA>55% (LEED v.4 requirements), Octopus (due to its capacity of multiple objectives) is the only choice? Any other approaches within grasshopper?
The alternative approach in my mind as a GH beginner is as follows. But I am not sure whether it is doable. Again, your comments will be greatly appreciated.
Since all my room/window/shades dimension are controlled by number sliders, I am thinking whether a component from GH will trigger these number sliders (not necessary to be all of them but one by one) automatically. If this is possible, I can do "data recorder" to record outputs from ASE and sDA. Eventually I will have a database of the input parameters and sDA/ASE results.
Does it make sense? Is there a component which can trigger number slider output at certain step?
Many thank!
Cheney …
GH, same as using sweep2 command in Rhino.
The one on the right is what I got so far (the output smooth our the kink of the original rails). Basically I am just following the methods provided by sdk sample: http://wiki.mcneel.com/developer/sdksamples/sweep2 .
The following is the function I copy and use directly from the SDK sample. By using this function, I can generate the sweep surface at right. But I want to have is the one in the middle with the kink edges. Can anyone show me how and where to modify he settings? I guess some sweep arguments need to be changed? I have try couples, such m_simplify, m_bSimpleSweep, m_bSameHeight, m_rebuild_count... but still cannot find a right combination for this function to output the sweep surface I want. Any suggestions or helps are very appreciated. Thanks for your help and time on this.
'Sweep2 function'----------------
Sub Sweep2( ByVal Rail1 As IOnCurve, _
ByVal Rail2 As IOnCurve, _
ByVal sCurves As List(Of IOnCurve), _
ByRef Sweep2_Breps As List(Of OnBrep))
'Define a new class that contains sweep2 arguments
Dim args As New MArgsRhinoSweep2
'Set the 2 rails
Dim Edge1 As New MRhinoPolyEdge
Dim Edge2 As New MRhinoPolyEdge
Edge1.Append(Rail1.DuplicateCurve())
Edge2.Append(Rail2.DuplicateCurve())
'Add rails to sweep arguments
args.m_rail_curves(0) = Edge1
args.m_rail_curves(1) = Edge2
args.m_bClosed = False
Dim section_curves As New List(Of OnCurve)
'Loop through sections to set parameters
For Each Section As IOnCurve In sCurves
Dim sCurve As OnCurve = Section.DuplicateCurve()
section_curves.Add(sCurve)
Dim t0 As Double = 0
If Not Edge1.GetClosestPoint(sCurve.PointAtStart(), t0) Then
If Not Edge1.GetClosestPoint(sCurve.PointAtEnd(), t0) Then
Dim s As Double = 0
sCurve.GetNormalizedArcLengthPoint(0.5, s)
Edge1.GetClosestPoint(sCurve.PointAt(s), t0)
End If
End If
args.m_rail_params(0).Append(t0)
Dim t1 As Double = 0
If Not Edge2.GetClosestPoint(sCurve.PointAtStart(), t1) Then
If Not Edge2.GetClosestPoint(sCurve.PointAtEnd(), t1) Then
Dim s As Double = 0
sCurve.GetNormalizedArcLengthPoint(0.5, s)
Edge2.GetClosestPoint(sCurve.PointAt(s), t1)
End If
End If
args.m_rail_params(1).Append(t1)
Next
'Set shapes
args.m_shape_curves = section_curves.ToArray
'Set the rest of parameters
args.m_simplify = 0
args.m_bSimpleSweep = False
args.m_bSameHeight = False
args.m_rebuild_count = -1 'Sample point count for rebuilding shapes
args.m_refit_tolerance = RMA.Rhino.RhUtil.RhinoApp.ActiveDoc.AbsoluteTolerance()
args.m_sweep_tolerance = RMA.Rhino.RhUtil.RhinoApp.ActiveDoc.AbsoluteTolerance()
args.m_angle_tolerance = RMA.Rhino.RhUtil.RhinoApp.ActiveDoc.AngleToleranceRadians()
Dim sBreps() As OnBrep = Nothing
If (RhUtil.RhinoSweep2(args, sBreps)) Then
For Each b As OnBrep In sBreps
Sweep2_Breps.Add(b)
Next
End If
Return
End Sub
…
s levels of detail by subdividing a 6 sided cube mesh and projecting its vertices according to a referenced height map. This is one of the standard conventions for building full sizes planets. At the lowest level (0) the mesh planet is made of 6 pieces(each 32x32 resolution). The next level down (1) is made of 24 pieces... 6 divided by 4 = 24. Level (2) is 96 quads etc etc. The script will generate each quad at its sub-division level and compare edge vertices to neighboring quads. It will then make sure any shared vertices are in fact at the same projected vector. This ensures a planet quad with edge vertices that match.
The problems comes in texturing each quad.
If I build the quad as a nurb surface from points I can place the texture easily because each surface UV maps squarely to my texture map (which is also square).
If I build the quad as a mesh I cannot just apply the square texture to the mesh UVs. This is because when you unwrap the UVs from a mesh they will not unwrap like a nurb surface's UVs. Therefore to get the correct mapping I would have to manipulate each UV back to an evenly aligned array (which is 1024 points in a 32x32 resolution UV). Maya and blender have 'relax uv' and 'align UV' functions but they don't do the trick and manual corrections are out of the question. So why not skip the mesh method and use the nurb method?
I did this and there is a trade off. The nurb will accept the material texture I want with no other work on my end but when I export the object as an .obj rhino creates its own mesh to describe the nurb(with various unsatisfactory setting options). This works great up to a point because at some level the interpreted mesh will have vertices that do no match at the edges, ie .. creating visible seams in the mesh. The picture below is the nearly seamless planet at LOD(1) made of 24 quads, each with 32x32 vertice resolution and a 512x512 jpg texture running in Unity3d 5. It works but at close level there are seams. This will be resolved simply by having the next LOD(x) instantiate before getting close enough to see the seam but at core nerd level I want the seamless mesh.
So, I can make the seamless mesh but I can not realistically texture map it. I can also make the nurb surface from points and texture it at the expense of the edge vertices matching. I am at the split in the road but I want to have my cake and eat it too. Thoughts, comments, trolls...?
Thanks for reading =)
Footnote: For you pros I am not using seamless noise across the map I am using grasshopper to sew up my otherwise non perfect edges.
Other programs in the pipeline:
-WorldMachine 2
-Wilbur
-Photoshop
-Unity3d…
:
______________________________________________________________________
As most of you know by now, Grasshopper will be included in Rhino 6 for Windows. We are almost finished with the Grasshopper in Rhino 6 development and you are invited to try it.
There are many enhancements, including:
High DPI displays are now supported.
Compatible with existing Grasshopper plug-ins.
New components including Make2D, Bend, Flow, Maelstrom, Splop, Splorph, Stretch, Taper, and Twist...
GhPython is now included. It features its own GHA compiler and a major node-in-code speed up.
Stable development target: Your plug-ins continue to work each minor Grasshopper upgrade.
RhinoCommon enhanced: More Rhino core functionality is accessible from within Grasshopper.
Developer documentation is online with guides and API references.
Now:
Download the current Rhino WIP for Windows
Try all your existing Grasshopper definitions
Report any problems you find here...
We want to make sure this new Grasshopper works for you. If you have any issues, David needs to hear from you very soon.
Thank you,
- Bob
Visit Grasshopper at: http://www.grasshopper3d.com/?xg_source=msg_mes_network
______________________________________________________________________
So...
Any news about OS X version? Many of us won't use Parallels or whatever win emulator or have a win machine nearby.
Hope you are working at it.
Cheers
gbrl
…
Added by Gabriel Netto at 3:44pm on October 29, 2016
o Common - just like C#. But Rhino Python has a "Scripting Language Wrapper" which breaks commonly used taks down to simpler functions.
Here's a general Example:
Take a look at the code on this website http://wiki.mcneel.com/developer/rhinocommonsamples/addline). Generally it's Rhino Common code in three language to create a line. They look equally difficult.
But if you use Rhino Python Scripting you can use an simplified syntax to get the same result. It's very similar to Rhino Script.
The code would be:
import rhinoscriptsyntax as rsstart_point = rs.GetPoint("Get start point")end_point = rs.GetPoint("Get end point")line_id = rs.AddLine(start_point, end_point)
OK - No Error Tracking here, but still you can see that the syntax is much simpler. (And in the end you just have less lines of code you have to debug.
And the good thing about Rhino Python is, that you can mix these approaches. Once you reach a level where Rhino Python Script doesn't get you there, which by the way happens very rarely, you can still use the Rhino Common methods.
Also, in Python Sycripting 99% of what you probably would like to do is available as a "wrapped" script function.
Rhino Python Script is currently also better documented than Rhino Common for C# and VB.Net. If you have used Rhino VB Script before, these functions will be very familar to you.
I'm not sure, why it's currently a separate plug-in. I belive the reason is that Rhino 4 (which is supported by GH) doesn't support Rhino Python. Also it's currently WIP, so it needed to be updated more frequently than GH itself. In the long run (I believe) it might be integrated into GH as a general component
- Martin
P.S.: To use Rhino Python within GH is a little more tricky than my example - but nothing compared to developing C#
P.S.2 Here's the code with Error Tracking:
import rhinoscriptsyntax as rsdef AddLine(): start_point = rs.GetPoint("Get start point") if start_point is None: print "No start point was selected" return end_point = rs.GetPoint("Get end point") if end_point is None: print "No end point was selected" return line_id = rs.AddLine(start_point, end_point) return line_idAddLine()
…
(1) I have been exporting small sections of a larger model into Maya from Rhino as FBX. In Maya I rotate and scale the models (-90 in X, Scale XYZ 0.001). The Named Views are being saved, but do not have a successful import into the Maya model. They do not appear as in Rhino, and the problem is not solved by scaling or rotating the cameras.
(2) If I try going the other direction, the cameras exported from Maya as FBX are also not aligning with the model in Rhino as they are in Maya.. I will do my best to post some images of the problem and hope you can help.
error !!
This is what the named views look like
here I am trying to the other way with a good view from Maya
strange placement..
This is the best result I can achieve, after I scale the camera by 1000
Any Advice???
Thanks, Robert.
…
ysim.ning.com/
When you run the simualtion you will notice on the batch terminal that Daysim is also being called, so you may want to consider how Daysim uses Radiance files & data.
Regarding your current problem, I think you stumbled onto something weird and interesting.
Interior and exterior readings appear to differ by 40 in the best case scenarios. Even setting the transmittance to 1 yields similar results. I tried changing from cummulative sky to climate sky and got similar values. Changing the test points did nothing either.
I think, (yet I'm too lazy to prove this) that the difference in values stems from diffuse radiation over the sky dome.
If you delete everything except the glass you'll notice that interior values are like 80-90% of the exterior values (this seems like the expected behaviour with a transmittance of 1). So, if we consider that a vertical window, part of an opaque box, is receiving radiation from 25% of a sphere, as you start to inset the interior test points the radiation they receive will be a fraction of the 25%.
Let me try to explain this better...The exterior surface receives radiation from a section of a sphere calculated by 180degrees on the xy plane (let’s call this angle theta) and by 90degrees (let’s call this angle phi) in azimuthal elevation. If you integrate this over spherical coordinates (theta from 0 to pi; phi from 0 to pi/2) you will find that it comes to a quarter of a sphere. By comparison, the interior surface will not integrate theta from 0 to 180degrees,nor phi from 0 to 90degrees, instead it will be the subtended angle from the exterior surface as a function of their separation; the farther in you go the smaller the view of the outside.
If my hypothesis is correct there shouldn't be that much difference since the separation is only 10cms...the subtended angle would be like 170 instead of 180 for theta and 85 instead of 90 for phi...overall if you integrate both spherical areas there should only by a difference of 10%.
In conclusion, I believe the unexpected behaviour stems from the previous subtended angle thing. If direct radiation was the only factor the difference would be the aforementioned 10%, which suggests that an additional source of energy is also affected by this. Perhaps indirect and diffuse radiation from other areas of the sky dome.
I’m definitely intrigued on why this is happening. Please post if you figure it out.
Regards,
Mauricio
…
he time to work with it.
the project is about facade strips which turns along height. the top angle is
parallel to the facade and the bottom is max. 90 degrees twisted, but the strips
should turn diffrently to achieve more dinamic look.
first i have tried to achieve this by calculating distance between the rotation angle from points of the grid and a single point.
then i have tried to ad some more effecting points and used the distance to the divided surface (the circles are just to control the area of effection):
i manually lofted it.
the result is a bit annoying becouse the points that effect the angle are always visible:
i have triend to solve this by drawing a line and divided it to recieve points along the bottom of the geometry. the result is not working properly:
Anyway,
there must be a better/smoother way to achieve this. i would like to effect the twist of the surfaces by distance to a spline, but im just lost. can you help me please?
the problems im encountering:
0- distance spline to grid to effect the angle
1- list of x/y coordinates and angle of rotation for each point of the grid
2- export points to excel
3- lofting lines in one direction only (x1, x2, x3...)
4- reduce the list data to 2 decimal (0,00)
5- maybe angle from radian to degrees
thx…
ss lots of questions,Hope guys show me some more different ways to figure out thoes kinds of problems,Thanks.
That is a construction project,the balconies should be overhang between 1 to 3 meters.
Program A is a patten consist of increasing balconies as the floors get upper.(In the picture is 29 at the first floor and ended with 2 more balconies for each floor, )Each part for a different floor,the twelfth floor have 29+(12-1)*2=51 balconies.
Questions From A,
A1:How to use the {(series)} to creat this atrium,As the floors increase the number of the balconies change by arithmetic progression.
A2:How to control the angle of the balconies,both the angle with floor and the balconies ending part.
Program B is use line to shape the commercial atrium,program A is more small pieces of rectangles.The {(TweenCrv)} command.
Questions From B,
B1:How to draw random points between the 1 to 3 meters region of the balcony,And those point form a shape also belongs to that region.
B2:Use a curve or other ways to control the changing speed of each floors' balcony.Right now the balcony is a Linear change.
Thanks for your Help.
Q1:Is there a way in Grasshopper to control the model to Modulus,less different unit parts to build such a Atrium.(For Exanple,only use 900mm and 600mm two different width of the Glass railings to bulid the model A OR B)…
y using the Honeybee_Update Honeybee component.
The video below (best viewed in full-screen mode) provides an idea of what these components are capable of being used for:
The video below shows how these components can be used in an existing Honeybee project (for additional links please open this video in youtube):
I have uploaded two examples as Hydra files that show how these components can be used for grid-point and image-based simulations:
Example1 : Grid Point Calculations
Example2: Image based simulation
Finally, a more esoteric application is demonstrated in this video:
These components are still in the beta-testing stage. Some of the limitations of the components are:
1. Only Type C photometry IES files are supported at present.
2. Rhino is likely to get sluggish if there are too many luminaires (i.e. light fixtures) present in a scene.
3. Due to the spectral limitations of the ray-tracing software (RADIANCE), simulations involving color mixing might not be physically realizable.
Additional details about photometric and spectral calculations are probably an overkill for this forum. However, I'd be glad to answer any related questions. Please report any bugs or request new features either on this forum or on Github.
Mostapha, Leland Curtis, Reinhardt Swart and Dr. Richard Mistrick provided valuable inputs during the development of these components.
Thanks,
Sarith
Update 16th January 2017:
An example with some new components and bug fixes since the initial release announcement can be found here
…