till quite rough.
I went through your attached log but it seems to be a successful run, perhaps the error log wasn't attached. In any case, I believe we have identified this issue. The goal of the update fvSchemes component was to apply schemes to finalized meshes in an automatic way. While this is useful for new users it is also a dangerous thing to do in CFD studies.
The component works by relating mesh quality to the mesh non-orthogonality, which the checkMesh component reports. While non-orthogonality is one of the important criteria of mesh quality it does present difficulties on some kind of meshes, especially like the simple cases that BF has been meshing so far.
The example case of simple box buildings in a wind tunnel above for instance will appear as a good quality case for even the lowest of cell-count meshes, simply because it is an orthogonal geometry. That means that checkMesh will probably report low values (imagine an empty blockMesh of 10m blocks has a non-orthogonality of 0) which in turn means that higher order schemes might be paired with actually low quality meshes. This I believe is causing problems.
I posted a possible solution to this here https://github.com/mostaphaRoudsari/Butterfly/issues/57. The idea is that Buttefly provides additional options to the users, enabling them to choose between first-order (faster, more robust, but lower quality schemes) and second-order (slower, less robust, but more accurate) schemes depending on mesh quality, stage of assessment, etc. In cases like the above mesh quality a first-order scheme might provide a better option. To test this I am attaching an fvSchemes file you can use by replacing yours in the /system folder of the case.
As a note however, I would like to stress there is so much that a tool like Butterfly can provide in this area. Meshing is a quite complicated and demanding part of the process, involving a lot of trial and error. Sometimes the problem is just the mesh and not the solution options (GIGO stands true in CFD as well). It does however get easier with experience. The safe advice is the simplest one: when changing solution options doesn't help, refine mesh and run again.
Kind regards,
Theodore.…
tangle. It doesn't need to me something complicated, it can look like this some of these roofs for example:
http://www.google.com/imgres?imgurl=http://www.zigersnead.com/blog/wp-content/uploads/2007/10/southern-cross-station-image-10.jpg&imgrefurl=http://www.zigersnead.com/current/blog/category/architecture/&usg=__0PpBu9zdO4Mg7TvHGIBKNsJPYuA=&h=395&w=640&sz=60&hl=en&start=471&zoom=1&tbnid=AIgPprbX_LhEQM:&tbnh=106&tbnw=172&ei=jsqRTan5BdHs4gaVt9HJAg&prev=/images%3Fq%3Dorganic%2Bshaped%2Broof%26hl%3Den%26sa%3DX%26biw%3D1666%26bih%3D1024%26tbs%3Disch:1&chk=sbg&itbs=1&iact=rc&dur=234&oei=VMqRTaXcNoz14QbRz8yfAg&page=10&ndsp=53&ved=1t:429,r:14,s:471&tx=51&ty=84
Where can I find that kind of Grasshopper file, that will enable me doing this?
Thank you.…
are now in 72 branches
I need the points to be in sorted out per line, that is.. 30 branches
what I actually need is to then cull the lines that have more than 2 intersections, maybe there is an easier way to do this?
Thank you very much for your help!!
…
.0004. [1 of 7] Writing simulation parameters...5. [2 of 6] No context surfaces...6. [3 of 6] Writing geometry...7. [4 of 6] Writing materials and constructions...8. [5 of 7] Writing schedules...9. [6 of 7] Writing loads and ideal air system...10. [7 of 7] Writing outputs...11. ...... idf file is successfully written to : c:\ladybug\unnamed\EnergyPlus\unnamed.idf12. 13. Analysis is running!...14. c:\ladybug\unnamed\EnergyPlus\eplusout.csv15. ......
Done! Read below for errors and warnings:
16. 17. Program Version,EnergyPlus, Version 8.2.7-777c1f8d79, YMD=2015.02.28 16:09,IDD_Version 8.2.718. 19. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.20. 21. ** Warning ** Version: in IDF="'8.2.7'" not the same as expected="8.2"22. 23. ** Warning ** ManageSizing: For a zone sizing run, there must be at least 1 Sizing:Zone input object. SimulationControl Zone Sizing option ignored.24. 25. ** Warning ** ManageSizing: For a plant sizing run, there must be at least 1 Sizing:Plant object input. SimulationControl Plant Sizing option ignored.26. 27. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=F73533B3C6894C67936B_GLZP_1228. 29. ** ~~~ ** Opening Surface creating error=F73533B3C6894C67936B_GLZP_12_GLZ_1230. 31. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=F73533B3C6894C67936B_GLZP_2532. 33. ** ~~~ ** Opening Surface creating error=F73533B3C6894C67936B_GLZP_25_GLZ_2534. 35. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=F73533B3C6894C67936B_GLZP_2836. 37. ** ~~~ ** Opening Surface creating error=F73533B3C6894C67936B_GLZP_28_GLZ_2838. 39. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_940. 41. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_9_GLZ_942. 43. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_1044. 45. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_10_GLZ_1046. 47. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_1148. 49. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_11_GLZ_1150. 51. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_1552. 53. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_15_GLZ_1554. 55. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_2456. 57. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_24_GLZ_2458. 59. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_2560. 61. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_25_GLZ_2562. 63. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_3064. 65. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_30_GLZ_3066. 67. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_3268. 69. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_32_GLZ_3270. 71. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_3472. 73. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_34_GLZ_3474. 75. ** Warning ** GetSurfaceData: Very small surface area[2.94495E-004], Surface=F73533B3C6894C67936B_GLZP_076. 77. ** Warning ** GetSurfaceData: Very small surface area[3.84753E-004], Surface=F73533B3C6894C67936B_GLZP_178. 79. ** Warning ** GetSurfaceData: Very small surface area[9.16905E-004], Surface=F73533B3C6894C67936B_GLZP_380. 81. ** Warning ** GetSurfaceData: Very small surface area[4.96186E-004], Surface=F73533B3C6894C67936B_GLZP_482. 83. ** Warning ** GetSurfaceData: Very small surface area[2.37373E-005], Surface=F73533B3C6894C67936B_GLZP_684. 85. ** Warning ** GetSurfaceData: Very small surface area[6.35824E-004], Surface=F73533B3C6894C67936B_GLZP_786. 87. ** Warning ** GetSurfaceData: Very small surface area[5.86549E-004], Surface=F73533B3C6894C67936B_GLZP_888. 89. ** Warning ** GetSurfaceData: Very small surface area[7.63765E-004], Surface=F73533B3C6894C67936B_GLZP_1090. 91. ** Severe ** GetSurfaceData: Zero or negative surface area[-8.09566E-004], Surface=F73533B3C6894C67936B_GLZP_1292. 93. ** Warning ** GetSurfaceData: Very small surface area[1.51701E-004], Surface=F73533B3C6894C67936B_GLZP_1394. 95. ** Warning ** GetSurfaceData: Very small surface area[9.29917E-004], Surface=F73533B3C6894C67936B_GLZP_1596. 97. ** Warning ** GetSurfaceData: Very small surface area[2.94451E-004], Surface=F73533B3C6894C67936B_GLZP_1698. 99. ** Warning ** GetSurfaceData: Very small surface area[8.03294E-004], Surface=F73533B3C6894C67936B_GLZP_17100. 101. ** Warning ** GetSurfaceData: Very small surface area[6.83026E-004], Surface=F73533B3C6894C67936B_GLZP_18102. 103. ** Warning ** GetSurfaceData: Very small surface area[9.29917E-004], Surface=F73533B3C6894C67936B_GLZP_20104. 105. ** Warning ** GetSurfaceData: Very small surface area[3.19851E-005], Surface=F73533B3C6894C67936B_GLZP_21106. 107. ** Warning ** GetSurfaceData: Very small surface area[7.63765E-004], Surface=F73533B3C6894C67936B_GLZP_23108. 109. ** Severe ** GetSurfaceData: Zero or negative surface area[-4.05899E-004], Surface=F73533B3C6894C67936B_GLZP_25110. 111. ** Warning ** GetSurfaceData: Very small surface area[6.35824E-004], Surface=F73533B3C6894C67936B_GLZP_27112. 113. ** Severe ** GetSurfaceData: Zero or negative surface area[-9.91146E-004], Surface=F73533B3C6894C67936B_GLZP_28114. 115. ** Warning ** GetSurfaceData: Very small surface area[2.70158E-004], Surface=F73533B3C6894C67936B_GLZP_29116. 117. ** Warning ** GetSurfaceData: Very small surface area[3.22781E-004], Surface=F73533B3C6894C67936B_GLZP_30118. 119. ** Warning ** GetSurfaceData: Very small surface area[4.67821E-004], Surface=F73533B3C6894C67936B_GLZP_33120. 121. ** Warning ** GetSurfaceData: Very small surface area[3.22737E-004], Surface=F73533B3C6894C67936B_GLZP_34122. 123. ** Warning ** GetSurfaceData: Very small surface area[2.65634E-004], Surface=4BDFD67E6D0E486796CC_GLZP_0124. 125. ** Warning ** GetSurfaceData: Very small surface area[4.70736E-004], Surface=4BDFD67E6D0E486796CC_GLZP_1126. 127. ** Warning ** GetSurfaceData: Very small surface area[3.42507E-004], Surface=4BDFD67E6D0E486796CC_GLZP_3128. 129. ** Warning ** GetSurfaceData: Very small surface area[5.89276E-004], Surface=4BDFD67E6D0E486796CC_GLZP_4130. 131. ** Warning ** GetSurfaceData: Very small surface area[1.91146E-004], Surface=4BDFD67E6D0E486796CC_GLZP_6132. 133. ** Warning ** GetSurfaceData: Very small surface area[9.71205E-004], Surface=4BDFD67E6D0E486796CC_GLZP_7134. 135. ** Warning ** GetSurfaceData: Very small surface area[4.34494E-004], Surface=4BDFD67E6D0E486796CC_GLZP_8136. 137. ** Severe ** GetSurfaceData: Zero or negative surface area[-3.60159E-004], Surface=4BDFD67E6D0E486796CC_GLZP_9138. 139. ** Severe ** GetSurfaceData: Zero or negative surface area[-1.11946E-004], Surface=4BDFD67E6D0E486796CC_GLZP_10140. 141. ** Severe ** GetSurfaceData: Zero or negative surface area[-3.41257E-004], Surface=4BDFD67E6D0E486796CC_GLZP_11142. 143. ** Severe ** GetSurfaceData: Zero or negative surface area[-8.21483E-005], Surface=4BDFD67E6D0E486796CC_GLZP_15144. 145. ** Warning ** GetSurfaceData: Very small surface area[2.65716E-004], Surface=4BDFD67E6D0E486796CC_GLZP_16146. 147. ** Warning ** GetSurfaceData: Very small surface area[4.84044E-004], Surface=4BDFD67E6D0E486796CC_GLZP_17148. 149. ** Warning ** GetSurfaceData: Very small surface area[7.12297E-004], Surface=4BDFD67E6D0E486796CC_GLZP_19150. 151. ** Warning ** GetSurfaceData: Very small surface area[6.14324E-004], Surface=4BDFD67E6D0E486796CC_GLZP_22152. 153. ** Warning ** GetSurfaceData: Very small surface area[8.88887E-004], Surface=4BDFD67E6D0E486796CC_GLZP_23154. 155. ** Severe ** GetSurfaceData: Zero or negative surface area[-9.89060E-004], Surface=4BDFD67E6D0E486796CC_GLZP_24156. 157. ** Severe ** GetSurfaceData: Zero or negative surface area[-1.14849E-003], Surface=4BDFD67E6D0E486796CC_GLZP_25158. 159. ** Warning ** GetSurfaceData: Very small surface area[4.00479E-004], Surface=4BDFD67E6D0E486796CC_GLZP_27160. 161. ** Warning ** GetSurfaceData: Very small surface area[6.63061E-005], Surface=4BDFD67E6D0E486796CC_GLZP_28162. 163. ** Warning ** GetSurfaceData: Very small surface area[1.09018E-004], Surface=4BDFD67E6D0E486796CC_GLZP_29164. 165. ** Severe ** GetSurfaceData: Zero or negative surface area[-2.49326E-005], Surface=4BDFD67E6D0E486796CC_GLZP_30166. 167. ** Severe ** GetSurfaceData: Zero or negative surface area[-3.17446E-004], Surface=4BDFD67E6D0E486796CC_GLZP_32168. 169. ** Warning ** GetSurfaceData: Very small surface area[8.60686E-004], Surface=4BDFD67E6D0E486796CC_GLZP_33170. 171. ** Severe ** GetSurfaceData: Zero or negative surface area[-2.48515E-005], Surface=4BDFD67E6D0E486796CC_GLZP_34172. 173. ** Fatal ** GetSurfaceData: Errors discovered, program terminates.174. 175. ...Summary of Errors that led to program termination:176. 177. ..... Reference severe error count=24178. 179. ..... Last severe error=GetSurfaceData: Zero or negative surface area[-2.48515E-005], Surface=4BDFD67E6D0E486796CC_GLZP_34180. 181. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).182. 183. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.184. 185. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.186. 187. ************* EnergyPlus Sizing Error Summary. During Sizing: 2 Warning; 0 Severe Errors.188. 189. ************* EnergyPlus Terminated--Fatal Error Detected. 41 Warning; 24 Severe Errors; Elapsed Time=00hr 00min 1.51sec190.…
ius, like the image below. I have a string with all of the 8 radii in a group of data. I was using the Divide Surface command, but there are two problems. First, the resulting points have a tree structure shown in the screenshot below, with {8; 2; 3}. How do I assign radius so that the six holes on the same panel has the same radius? The second problem is, the divide surface command generates points along the edges, too, where I don’t need any holes. How can I get rid of them?
…
d the number slider is going to take these values:
84
84.12903284.25806584.38709784.51612984.64516184.77419484.90322685.03225885.1612985.29032385.41935585.54838785.67741985.80645285.93548486.06451686.19354886.32258186.45161386.58064586.70967786.8387186.96774287.09677487.22580687.35483987.48387187.61290387.74193587.87096888.088.12903288.25806588.38709788.51612988.64516188.77419488.90322689.03225889.1612989.29032389.41935589.54838789.67741989.80645289.93548490.06451690.19354890.32258190.45161390.58064590.70967790.8387190.96774291.09677491.22580691.35483991.48387191.61290391.74193591.87096892.092.12903292.25806592.38709792.51612992.64516192.77419492.90322693.03225893.1612993.29032393.41935593.54838793.67741993.80645293.93548494.06451694.19354894.32258194.45161394.58064594.70967794.8387194.96774295.09677495.22580695.35483995.48387195.61290395.74193595.87096896.096.12903296.25806596.38709796.51612996.64516196.77419496.90322697.03225897.1612997.29032397.41935597.54838797.67741997.80645297.93548498.06451698.19354898.32258198.45161398.58064598.70967798.8387198.96774299.09677499.22580699.35483999.48387199.61290399.74193599.870968100.0
divided by 100, but that's not the big deal ... The big deal is:
at every frame I need to have a different colour for a specific object... How to do this?!…
lts.
In the visualization, points is an interesting option. It's a matter of aesthetics I guess, I go with surfaces :) Also what you can try is selecting Filters -> Slice (you can also find it in the icons above the pipeline viewer), in the Slice options below the pipeline press Z normal and on the Z coordinate press some height relevant to the buildings (e.g. 1.75m a typical human scale). That would show you the flow around the buildings on that height. Experiment with selecting other normals and values. Keep playing with the filters there's some cool things in there. Also you can check out the mailing list and extensive paraview documentation.
Concerning the errors I apologize because I just downloaded your case.
It appears that the decomposeParDict is not included in the system folder. I am not sure if this is due to BF not going through the whole workflow yet or an ommission on our side. Please feel free to add it in Github. I will also note it down and pass it to Mostaph to check. In the meantime please find attached a VERY detailed decomposeParDict file. I took the liberty to set it at 4 processors (the numberOfSubDomains value) and also selected (that is uncommented) the scotch decomposition method. It's the easiest method to use since it is automatic and doesn't require any more inputs on how the domain is decomposed on the x,y,z directions (which would require you to change values in the attached file).
Now, the different folders created are simply snapshots of the current solution at the specific timestep. To control how often the solver is saving change the writeInterval number in the controlDict file. You can also change almost all these values on the fly, while OF is running.
Finally, concerning the other errors of parafoam it seems somehow parafoam is reading the intial condition names instead of actual results from the solution files and it doesn't like it.
Does this happen only when you open the case (i.e. at 0 time) or does it also happen when you move to an other timestep?
Also, are you using paraFoam, paraview or the paraFoam -builtin method?
The extension of the paraFoam file seems to be .foam which means you are probably using the built in viewer. That might be the issue but I'm not sure.
Can you try running paraview, navigate to your case folder, open the .foam file and see if there is still an error?
Also, if it isn't much trouble can you zip one of the time folders and attach it here? I'd like to take a look at what's inside to check against what the error report says.
Once again thanks for testing!
Kind regards,
Theodore.…