NONE, in SIZING:PARAMETERS". I'm not sure of where to start in troubleshooting this. I've attached the file.
Thank you,
See the errors and warnings below:
{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. [1 of 8] Writing simulation parameters...
3. [2 of 8] Writing context surfaces...
4. [2 of 8] Writing context surfaces...
5. [3 of 8] Writing geometry...
6. [4 of 8] Writing Electric Load Center - Generator specifications ...
7. [5 of 8] Writing materials and constructions...
8. [6 of 8] Writing schedules...
9. [7 of 8] Writing loads and ideal air system...
10. [8 of 8] Writing outputs...
11. ...
... idf file is successfully written to : R:\Green\SuRG\Building_Performance_Analysis\2016_analysis_studies\Energy_Analysis_Comparison\Honeybee_+_Ladybug\tutorial01\EnergyPlus\tutorial01.idf
12.
13. Analysis is running!...
14. ...
...
Done! Read below for errors and warnings:
15.
16. Program Version,EnergyPlus, Version 8.5.0-c87e61b44b, YMD=2016.10.31 11:39,IDD_Version 8.5.0
17.
18. ************* IDF Context for following error/warning message:
19.
20. ************* Note -- lines truncated at 300 characters, if necessary...
21.
22. ************* 24 Sizing:Parameters,
23.
24. ************* Only last 1 lines before error line shown.....
25.
26. ************* 25 None, !- Heating Sizing Factor
27.
28. ** Severe ** IP: IDF line~25 Invalid Number in Numeric Field#1 (Heating Sizing Factor), value=NONE, in SIZING:PARAMETERS
29.
30. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
31.
32. ** ~~~ ** Possible Invalid Numerics or other problems
33.
34. ** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
35.
36. ...Summary of Errors that led to program termination:
37.
38. ..... Reference severe error count=1
39.
40. ..... Last severe error=IP: IDF line~
, value=NONE, in SIZING:PARAMETERS
41.
42. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
43.
44. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
45.
46. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
47.
48. ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
49.
50. ************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 9.34sec
51.…
(18, 11, 0, 17), also put in the assembly component.
How can I know which value of the reaction forces correspond to which support?
In the manual is stated that when the reaction force component is used, than the values are displayed in ascending sequence of the corresponding nodes.So if I input the support nodes like thispoint with index 18point with index 11point with index 0point with index 17are the reaction forces displayed like this (per loadcase)?0 - reaction forces in point with index 01 - reaction forces in point with index 112 - reaction forces in point with index 183 - reaction forces in point with index 17
Thanks!
BestLara…
the first area and the first number, the second area and the second number and the third are and the third number. For example, let's assume we have the following areas {65, 15, 20}. The absolute difference between these two sets equals {abs(44-65), abs(39-15), abs(17-20)} == {21, 24, 3}. The sum-total of all these absolute differences is your fitness, i.e. 21+24+3 = 48. This number has to go to zero.
If we enter the results you just got, then the absolute differences look like this: {abs(44-44), abs(39-17), abs(17-39)} == {0, 22, 22}, which results in a fitness of 44. Only an exact match will result in a fitness of zero.
--
David Rutten
david@mcneel.com
Seattle, WA…
Added by David Rutten at 12:44pm on November 13, 2010
0,
I want to move everything in {2} up 5 and 10 and 15,
Any ideas. I have been trying using the series component to create the right data structure but somehow its not working and i am sure there is a simple way?
Do i have to repeat the data so that the number of transform data matches the input list or is there a way to simply apply the transformation to everything in {0}{1} and {2} respectively depending on its structure ??
Hopefully this makes sense? I am not really sure but is it a job for stream - i cant understand why i cant get it to work. Sorry i am sure this is covered in the forums, i have been looking but cant anything which helps specifically.
Many thanks
Chris…
sign agency that was founded in Clerkenwell, London, in 1986. Since then, studios in Amsterdam, Singapore, and New York have been growing. In 2015, it was named D&AD’s Most Awarded Design Agency, and Agency of the Year at the Pentawards.…
ndom S (Seed)' input is different for each component in the Lynda tutorial code (8, 17, 13) but all the same (2) in your copy.
There are many ways to make the seed values different, individually or all three at once:
…
ot = rs.AddPlanarSrf(i)[0]
With:
boun_srf_plot = rs.AddNetworkSrf(rs.coercecurve(i).Explode())
Not guaranteed in all cases, but should work for you here.…
rotations per second. If I test the quad stepper on a smaller stepper like this one ((http://robotics.reefat.com/wp-content/uploads/2008/08/PF35T-48L4.pdf), I'm able to get faster speeds.
At first I thought this was a hardware/power supply issue, but I tested a sample sketch from this site: http://lusorobotica.com/index.php/topic,106.0.html on the Vexta NEMA 17 and was able to get the increased speeds I was looking for.
I can't get higher speeds than .3 rotations per second using the Quadstepper Component. Is there any way there a line in the code which is limiting the max speed?
Thanks for any help.
-Erick…
Added by lmnts to Firefly at 12:18pm on October 26, 2012