ther math and logic. i can usually conceptualise what i want to do and cobble some semi working thing together but don't know which components to use and how to patch it. so i'm super happy to have someone who knows what he's doing to find this interesting.
and i'm glad you mention the fanned frets again, there is one input parameter that's still missing for the multiscale frets to be fully parametric, it's the angle of the nut or which fret should be straight. it depends a bit on personal preferences and playing posture what is more comfortable. so being able to adjust this easily would be cool. again i have no idea how the maths for that work or if you can just rotate each fret the same amount around it's middle point. The input either as fret number (for the straight fret) or as a simple slider from bridge to nut should do as input setting.
Here are the two extremes and the middle ground:
i've been thinkin today while analysing your patches and cleaning up my mess what exactly the monster should do.
Here are the input parameters needed, i think it's the complete list
scale length low E string
scale length high e string
fret angle/straight fret
string width at nut
string width at bridge
number of frets
fretboard overhang at nut (distance from string to fretboard bounds)
fretboard overhang at last fret
string gauges
string tensions
fretboard radius at nut (for compound radius fretboard radius at bridge is calculated with the stewmac formula)
fretwire crown width
fretwire crown height
action height at nut (distance between bottom of string and fretwire crown top)
action height at last fret
pickup 1 neck position
pickup 2 middle position
pickup 3 bridge position
nut width
the pickup positions should be used to draw circles for the magnet poles on each string so they are perfectly aligned and can be used for the pickup flatwork construction. ideally they would need a rotation control aligning the center line of the pickup so it's somewher between the last fret angle and bridge angle. personally i do this visually depending on the design i'm looking for, some people have huge theories on pickup positioning but personally i don't believe in it.
that should result in everything needed to quickly generate all the necessary construction curves or geometry for nut/fingerboard/frets/pickups. this is the core of what makes a guitar work, the more precise this dynamic system is the better the guitar plays and sounds.
i posted another thread trying to understand how i could use datasets form spreadsheets,databse, csv to organize the input parameters. What would make sense for the strings for example is hook into a spreadsheet with the different string sets, i attached one for the d'Addario NYXL string line which basically covers all combos that make sense.
The string tension is an interesting one, and implmenting it would sure be overkill albeit super interesting to try. it should be possible to extrapolate from the scale length of each string what the tension for a given string gauge of that string would be so that you could say 'i want a fully balanced set' or 'heavy top light bottom) and it would calculate which SKU from d'addario would best match the required tension. All the strings listed in the spreadsheet are available as single strings to buy.
i'm trying to reorganize everything which helps me understand it. i just discovered the 'hidden wires' feature which is great since once i understood what a certain block does or have finished one of my own, i can get the wires out of the way to carry on undistracted. a bit risky to hide so many wires but it makes it so much easier not to get completely lost :-)
btw, the 'fanned fret' term is trademarked, some guy tried to patent it in the 80's which is a bit silly since it has been done for centuries. there is a level of sophistication above this as well, check out http://www.truetemperament.com/ and that really is something else. it really is astounding how superior the tuning is on those wigglefrets, the problem is that it's rather awkward for string bending and also you can't easily recrown or level the frets when they are used. …
e matching with a dedicated component which creates combinations of items. You can find the [Cross Reference] component in the Sets.List panel.
When Grasshopper iterates over lists of items, it will match the first item in list A with the first item in list B. Then the second item in list A with the second item in list B and so on and so forth. Sometimes however you want all items in list A to combine with all items in list B, the [Cross Reference] component allows you to do this.
Here we have two input lists {A,B,C} and {X,Y,Z}. Normally Grasshopper would iterate over these lists and only consider the combinations {A,X}, {B,Y} and {C,Z}. There are however six more combinations that are not typically considered, to wit: {A,Y}, {A,Z}, {B,X}, {B,Z}, {C,X} and {C,Y}. As you can see the output of the [Cross Reference] component is such that all nine permutations are indeed present.
We can denote the behaviour of data cross referencing using a table. The rows represent the first list of items, the columns the second. If we create all possible permutations, the table will have a dot in every single cell, as every cell represents a unique combination of two source list indices:
Sometimes however you don't want all possible permutations. Sometimes you wish to exclude certain areas because they would result in meaningless or invalid computations. A common exclusion principle is to ignore all cells that are on the diagonal of the table. The image above shows a 'holistic' matching, whereas the 'diagonal' option (available from the [Cross Reference] component menu) has gaps for {0,0}, {1,1}, {2,2} and {3,3}:
If we apply this to our {A,B,C}, {X,Y,Z} example, we should expect to not see the combinations for {A,X}, {B,Y} and {C,Z}:
The rule that is applied to 'diagonal' matching is: "Skip all permutations where all items have the same list index". 'Coincident' matching is the same as 'diagonal' matching in the case of two input lists which is why I won't show an example of it here (since we are only dealing with 2-list examples), but the rule is subtly different: "Skip all permutations where any two items have the same list index".
The four remaining matching algorithms are all variations on the same theme. 'Lower triangle' matching applies the rule: "Skip all permutations where the index of an item is less than the index of the item in the next list", resulting in an empty triangle but with items on the diagonal.
'Lower triangle (strict)' matching goes one step further and also eliminates the items on the diagonal:
'Upper Triangle' and 'Upper Triangle (strict)' are mirror images of the previous two algorithms, resulting in empty triangles on the other side of the diagonal line:
…
lla progettazione parametrica e le tecniche di modellazione algoritmica per la generazione di forme complesse
___________________________________________________________________________________
luogo:
Sala meeting Hotel Mercure Milano Centro Piazza Oberdan 12 – 20129 MILANO
Scadenza iscrizioni: 12 Novembre 2011 – ore 15.00
___________________________________________________________________________________
info e prenotazioni:
Le Penseur (coordinamento formazione)
info@lepenseur.it
081 564 21 84
347 548 71 78
quote di partecipazione e programma (formato PDF)
ulteriori informazioni sui corsi PLUG > IT
___________________________________________________________________________________
PROGRAMMA DEL CORSO
GIORNO_01
10.00 – 10.30: presentazione workshop
10.30 – 11.30: introduzione alla progettazione parametrica: teoria, esempi, casi studio
11.30 – 13.00: Grasshopper: concetti base, logica algoritmica, interfaccia grafica
13.00 – 14.00: break | lunch
14.00 – 16.00: nozioni fondamentali: componenti, connessioni, data flow
16.00 – 18.00: esercitazione
GIORNO_02
10.00 – 12.00: funzioni matematiche e logiche, serie, gestione dei dati
12.00 – 15.00: analisi e definizione di curve e superfici
GIORNO_03
10.00 – 12.00: definizione di griglie e pattern complessi
12.00 – 13.00: trasformazioni geometriche, paneling
13.00 – 14.00: break | lunch
14.00 – 16.00: esercitazione
16.00 – 18.00: attrattori, image sampler
GIORNO_04
10.00 – 13.00: data tree: gestione di dati complessi
13.00 – 14.00: break | lunch
14.00 – 15.00: digital fabrication: teoria ed esempi
15.00 – 18.00: nesting: scomposizione di oggetti tridimensionali in sezioni e posizionamento su piani di taglio per macchine a controllo numerico CNC…
nowledge, tools, materials and machines. The Clusters provide a focus for workshop participants working together within a common framework.
Clusters provide a forum for the exchange of ideas, processes and techniques and act as a catalyst for design resolution. The Workshop is made up of ten Clusters that respond in diverse ways to the sg2012 Challenge Material Intensities. The Call for Clusters is now open to proposals which respond in innovative ways to this year's challenge.
Deadline: September 19 2011
More information can be found here:
http://smartgeometry.org/index.php?option=com_content&view=article&id=129&Itemid=146
sg2012 takes place from 19-24 March 2012 at EMPAC (http://empac.rpi.edu/) and is hosted by Rensselaer Polytechnic Institute in Troy, upstate New York USA. The Workshop and Conference will be a gathering of the global community of innovators and pioneers in the fields of architecture, design and engineering.
The event will be in two parts: a four day Workshop 19-22 March, and a public conference beginning with Talkshop 23 March, followed by a Symposium 24 March. The event follows the format of the highly successful preceding events sg2010 Barcelona and sg2011 Copenhagen.
sg2012 Challenge Material Intensities
Simulation, Energy, Environment
Imagine the design space of architecture was no longer at the scale of rooms, walls and atria, but that of cells, grains and vapour droplets. Rather than the flow of people, services, or construction schedules, the focus becomes the flow of light, vapour, molecular vibrations and growth schedules: design from the inside out.
The sg2012 challenge, Material Intensities, is intended to dissolve our notion of the built environment as inert constructions enclosing physically sealed spaces. Spaces and boundaries are abundant with vibration, fluctuating intensities, shifting gradients and flows. The materials that define them are in a continual state of becoming: a dance of energy and information.Material potential is defined by multiple properties: acoustical, chemical, electrical, environmental, magnetic, manufacturing, mechanical, optical, radiological, sensorial, and thermal. The challenge for sg2012 Material Intensities is to consider material economy when creating environments, micro-climates and contexts congenial for social interaction, activities and organisation. This challenge calls for design innovation and dialogue between disciplines and responsibilities.sg2010 Working Prototypes strove to emancipate digital design from the hard drive by moving from the virtual to the actual in wrestling with the tangible world of physical fabrication. sg2011 Building the Invisible focused on informing digital design with real world data. sg2012 Material Intensities strives to energise our digital prototypes and infuse them with material behaviour. They have the potential to become rich simulations informed by the material dynamics, chemical composition, energy flows, force fields and environmental conditions that feed back into the design process.
More information can be found at http://www.smartgeometry.org…
lla progettazione parametrica e le tecniche di modellazione algoritmica per la generazione di forme complesse
___________________________________________________________________________________
luogo:
Sala meeting Holiday Inn Inn Turin C.so Francia Piazza Massaua 21 – TORINO
Scadenza iscrizioni: 25 Novembre 2011 – ore 15.00
___________________________________________________________________________________
info e prenotazioni:
Le Penseur (coordinamento formazione)
info@lepenseur.it
081 564 21 84
347 548 71 78
quote di partecipazione e programma (formato PDF)
ulteriori informazioni sui corsi PLUG > IT
___________________________________________________________________________________
PROGRAMMA DEL CORSO:
GIORNO_01 | 01 Dicembre 2011
10.00 – 10.30: presentazione workshop
10.30 – 11.30: introduzione alla progettazione parametrica: teoria, esempi, casi studio
11.30 – 13.00: Grasshopper: concetti base, logica algoritmica, interfaccia grafica
13.00 – 14.00: break
14.00 – 16.00: nozioni fondamentali: componenti, connessioni, data flow
16.00 – 18.00: esercitazione
GIORNO_02 | 02 Dicembre 2011
10.00 – 12.00: funzioni matematiche e logiche, serie, gestione dei dati
12.00 – 13.00: analisi e definizione di curve e superfici
13.00 – 14.00: break
14.00 – 16.00: analisi e definizione di curve e superfici
16.00 – 18.00: definizione di griglie e pattern
GIORNO_03 | 03 Dicembre 2011
10.00 – 12.00: trasformazioni geometriche, paneling
12.00 – 13.00: image sampler
13.00 – 14.00: break
14.00 – 18.00: data tree: gestione di dati complessi
GIORNO_04 | 04 Dicembre 2011
10.00 – 12.00: digital fabrication: teoria ed esempi
12.00 – 13.00: nesting: scomposizione di oggetti tridimensionali in sezioni e posizionamento su piani di taglio per macchine a controllo numerico CNC
13.00 – 14.00: break
14.00 – 18.00: esercitazione…
.
Today we have gone live, and the plugin is available on Food4Rhino. You will find an installer package, sample files, and a demo video on getting started:
http://www.food4rhino.com/project/human-ui
Visit the Bitbucket Repo and poke around in the code:
https://bitbucket.org/andheum/humanui
Check out today's coverage in Architect Magazine:
http://www.architectmagazine.com/technology/nbbj-releases-human-ui-to-bring-parametric-modeling-to-the-masses_o
Finally join our group and ask any questions or post any comments here:
http://www.grasshopper3d.com/group/human-ui
See below for detailed description!
----------------------------------
Human UI
Primary Development by:
Lead Developer: Andrew Heumann / andheum / @andrewheumann
Product Manager: Marc Syp / marcsyp / @mpsyp
Contributing Developer: Nate Holland / nateholland / @_NateHolland
Gone are the days of faking a user interface by laying out sliders and text panels and hiding wires on the Grasshopper canvas. Human UI interfaces are entirely separate from the Grasshopper canvas and leverage the power of Windows Presentation Foundation (WPF), a graphical subsystem for rendering user interfaces in the Windows environment.
OLD NEW
In other words: Human UI makes your GH definition feel like a Windows app. Create tabbed views, dynamic sliders, pulldown menus, checkboxes, and even 3D viewports and web browsers that look great and make sense to anyone--including designers and clients with no understanding of Grasshopper.
Human UI has been in development at NBBJ for over a year, as part of a larger NBBJ Design Computation initiative to deliver our tools internally as Products -- with fully automated installation, managed dependencies, analytics, documentation, and “magical” user experience. Human UI has been a huge component of the user experience part of this puzzle, and we are excited to share it with the larger Grasshopper community so that others can benefit from it and contribute to its development.
The initial release of Human UI is accompanied by a few simple examples to get you started, but we have developed sophisticated user interfaces with these tools at NBBJ and will slowly be rolling out more advanced examples. We also look forward to opening up the development to the community and seeing what new features and paradigms we can add.
Download the plugin at Food4Rhino and get started building Custom UIs for Grasshopper right away! We are happy to answer any questions or field discussion in the dedicated Grasshopper Group. Please join us!
Join the Grasshopper Group
http://www.grasshopper3d.com/group/human-ui
Download the plugin + sample files
http://www.food4rhino.com/project/human-ui
Visit the Bitbucket Repo
https://bitbucket.org/andheum/humanui
We look forward to seeing where this project takes you, please share your projects made with Human UI!
Sincerely,
Design Computation Leadership Team, NBBJ
…
ur setup. Can you say what sensor you are using? Are you using an Arduino to write this ascii information to the serial port? If so, there may be some formatting code for the string that you'll need to do to get the Read component to function properly. I see that you were able to open the port and Start reading... so my first thought is that the data is formatted correctly....
All of the read components look for a specific character (in this case two characters) to indicate when it has reached the end of the line being read and should spit out the data. In this case, Firefly uses the Carriage Return (\r) and Line Feed (\n) to know when it has reached the end of the line. In arduino, these are automatically added to any line if you use the Serial.println("blah, blah, blah"); command. Notice, this is different from the Serial.print("nothing to see here"); command. This doesn't mean that you can't still use the regular print command... it's just you need to use the println command to indicate when you've reached the end of the line. Let's take a look at a simple example.
void setup() { Serial.begin(9600);}void loop() { int sensorValue = analogRead(A0); Serial.print("The value of the sensor is: "); Serial.println(sensorValue);
delay(20); // important to wait some small time so you aren't sending just a ton of info over to GH which will cause it to crash :(
}
The first print statement prints a string to the serial port... and the next one adds the current sensor value... and THEN adds the carriage return and line feed to start a new line. The nice thing about using these together is that you can concatenate any type of data you want. If you were to upload this sketch, you should see a sentence being printed to the serial port that says "The value of the sensor is: 512". I made up the number, but you get the idea. Notice, I also had to include a delay function. You don't always need this (there are other ways to go about this) but the important thing to note is that the loop cycle on the Arduino can run really fast. I mean... really fast. So, you wont want to send so much data over to GH, because this could flood the string buffer in the Read component and cause it to crash (eventually). It's a good idea to add some small time interval just to slow it down a bit. I should say that I've optimized the refresh rate in the next release so it's significantly faster... so hopefully this wont be as big of a problem... but hopefully that helps some.
Now... Why are you writing data to a sensor? Sensors by default are considered inputs... so I'm quite confused as to why you would want to send data back (if you are... then you need some way to handle the string data being sent from GH... this is the whole reason we built the Firefly firmata... it sets up the two-way protocol so you don't have to deal with all of that mess... If you're going to read and write, you're better off just uploading the firmata and using the Uno Read and Write components). Also, I'm not very familiar with the Hyperterm or Advanced Serial Port Terminal... but I will say that could get COM conflicts if you're trying to open the port with different tools. Anyway, I hope some of this helps you get up and running.
Cheers,
Andy
…
oftware connections built from the initial seed of the project. As always you can download the new release from Food4Rhino. Make sure to remove the older version of Ladybug and Honeybee and update your scripts.
This release is also special since today it is just about 3 years (3 years and 2 weeks) from the first release of Ladybug. As with any release, there have been a number of bug fixes and improvements but we also have some major news this time. In no specific order and to ensure that the biggest developments do not get lost in the extensive list of updates, here are the major ones:
Mostapha is re-writing Ladybug!
Ladybug for DynamoBIM is finally available.
Chris made bakeIt really useful by incorporating an export pathway to PDFs and vector-based programs.
Honeybee is now connected to THERM and the LBNL suite thanks to Chris Mackey.
Sarith has addressed a much-desired wish for Honeybee (Hi Theodore!) by adding components to model electric lighting with Radiance.
Djordje is on his way to making renewable energy deeply integrated with Ladybug by releasing components for modeling solar hot water.
There is new bug. Check the bottom of the post for Dragonfly!
Last but definitely not least (in case you’re not still convinced that this release is a major one) Miguel has started a new project that brings some of Ladybug’s features directly to Rhino. We mean Rhino Rhino - A Rhino plugin! Say hi to Icarus! #surprise
Before we forget! Ladybug and Honeybee now have official stickers. Yes! We know about T-Shirts and mugs and they will be next. For now, you can deck-out your laptops and powerhouse simulation machines with the symbology of our collaborative software ecosystem.
Now go grab a cup of tea/coffee and read the details below:
Rewriting Ladybug!
Perhaps the most far-reaching development of the last 4 months is an effort on the part of Mostapha to initiate a well structured, well documented, flexible, and extendable version of the Ladybug libraries. While such code is something that few community members will interact with directly, a well-documented library is critical for maintaining the project, adding new features, and for porting Ladybug to other software platforms.
The new Ladybug libraries are still under development across a number of new repositories and they separate a ladybug-core, which includes epw parsing and all non-geometric functions, from interface-specific geometry libraries. This allows us to easily extend Ladybug to other platforms with a different geometry library for each platform (ie. ladybug-grasshopper, ladybug-dynamo, ladybug-web, etc) all of which are developed on top of the ladybug-core.
Without getting too technical, here is an example of a useful outcome of this development. If you want to know the number of hours that relative humidity is more than 90% for a given epw, all that you have to code (in any python interface) is the following:
import ladybug as lb
_epwFile = r"C:\EnergyPlusV7-2-0\WeatherData\USA_CO_Golden-NREL.724666_TMY3.epw"
epwfile = lb.epw.EPW(_epwFile)
filteredData = epwfile.relativeHumidity.filterByConditionalStatement('x>90')
print "Number of hours with Humidity more than 90 is %d "%len(filteredData.timeStamps)
Compare that to the 500 + lines that you would have had to write previously for this operation, which were usually tied to a single interface! Now let’s see what will happen if you want to use the geometry-specific libraries. Let’s draw a sunpath in Grasshopper:
import ladybuggrasshopper.epw as epw
import ladybuggrasshopper.sunpath as sunpath
# get location data form epw file
location = epw.EPW(_epwFile).location
# initiate sunpath based on location
sp = sunpath.Sunpath.fromLocation(location, northAngle = 0, daylightSavingPeriod = None, basePoint =cenPt, scale = scale, sunScale = sunScale)
# draw sunpath geometry
sp.drawAnnualSunpath()
# assign geometries to outputs
...
Finally we ask, how would this code will look if we wanted to make a sunpath for dynamo? Well, it will be exactly the same! Just change ladybuggrasshopper in the second line to ladybugdynamo! Here is the code which is creating the sunpath below.
With this ease of scripting, we hope to involve more of our community members in our development and make it easy for others to use ladybug in their various preferred applications. By the next release, we will produce an API documentation (documentation of all the ladybug classes, methods and properties that you can script with) and begin making tutorials for those interested in getting deeper into Ladybug development.
LADYBUG
1 - Initial Release of Ladybug for Dynamo:
As is evident from the post above, we are happy to announce the first release of Ladybug for Dynamo! You can download the ladybug package from Dynamo package manager. Make sure to download version 0.0.6 which is actually 0.0.1! It took a number of trial and errors to get it up there. Once you have the file downloaded you can watch these videos to get started:
The source code can be find under ladybug-dynamo repository and (as you can already guess) it is using the new code base. It includes a very small toolkit of essential Ladybug components/nodes but it has enough to get you started. You can import weather files, draw sunpaths and run sunlighthours or radiation analyses.
There are two known issues in this release but neither of them is critical. You need to have Dynamo 0.9.1 or higher installed which you can download from here (http://dynamobuilds.com/). It is recommended that you run the scripts with ‘Manual’ run (as opposed to ‘Automatic’) since the more intense calculations can make Dynamo crash in automatic mode.
To put things in perspective, here is how we would map Ladybug for Dynamo vs Ladybug and Honeybee for Grasshopper on the classic ‘Hype graph’. The good news is that what we learned a lot from the last three years, making development of the Dynamo version easier and getting us to the plateau of productivity faster.
We should also note that the current development of the Dynamo interface is behind that of the Ladybug-Core, which means there are a number of features that are developed in the code but haven’t made their way to the nodes yet. They will be added gradually over the next month or two.
If you’re interested to get involved in the development process or have ideas for the development, follow ladybug on Facebook, Twitter and Github. We will only post major release news here. Facebook, github and twitter will be the main channels for posting the development process. There will also be a release of a new ladybug for Grasshopper soon that will use the came Ladybug-Core libraries as the Dynamo interface [Trying hard not to name it as Ladybug 2].
2 - New Project “Icarus” Provides Ladybug Capabilities Directly in Rhino
Speaking of expanded cross-platform capabilities, the talented Miguel Rus has produced a standalone Rhino Plugin off of the original Ladybug code that has been included in this release. After writing his own core C# libraries, Miguel’s plugin enables users to produce sunpath and run sunlight hours analyses in the Rhino scene without need of opening Grasshopper or engaging the (sometimes daunting) act of visual scripting.
This release includes his initial RHP plugin file. It is hoped that Miguel’s efforts will extend some of the capabilities of environmental design to individuals who are unfamiliar with visual scripting, casting the network of our community into new territory. We need your help spreading the word about Icarus since the people who will benefit the most from it have probably not read this far into the release notes. Also, as the project is in the early stages, your feedback can make a great difference. You can download the current release from this link.
Once you download the zip file. Right click and unblock it. Then extract the files under C:\Program Files\Rhinoceros 5 (64-bit)\Plug-ins\ folder. Drag and drop the RHP file into Rhino and you should be ready to go. You can either type Icarus in the command line or open it via the panels. Here is a short video that shows how to run a sunlighhours analysis study in Rhino.
3 - BakeIt Input Now Supports a Pathway to PDF +Vector Programs
As promised in the previous release, the BakeIt_ option available on Ladybug’s visual components has been enhanced to provide a full pathway to vector-based programs (like Illustrator and Inkscape) and eases the export to vector formats like PDFs.
This means that the BakeIt_ operation now places all text in the Rhino scene as actual editable text (not meshes) and any colored meshes are output as groups of colored hatches (so that they appear as color-filled polygons in vector-based programs). There is still an option to bake the colored geometries as light meshes (which requires smaller amounts of memory and computation time) but the new hatched capability should make it easier to incorporate Ladybug graphics in architectural drawings and documents like this vector psychrometric chart.
4 - Physiological Equivalent Temperature (PET) Now Available
Thanks to the efforts of Djordje Spasic, it is now possible to compute the common outdoor comfort metric ‘Physiological Equivalent Temperature’ (PET) with Ladybug. The capability has been included with this release of “Thermal Comfort Indices” component and is supported by a “Body Characteristics” component in the Extra tab. PET is particularly helpful for evaluating outdoor comfort at a high spatial resolution and so the next Honeybee release will include an option for PET with the microclimate map workflow.
5 - Solar Hot Water Components Available in WIP
Chengchu Yan and Djordje Spasic have built a set of components that perform detailed estimates of solar hot water. The components are currently undergoing final stages of testing and are available in the WIP tab of this release. You can read the full release notes for the components here.
6 - New Ladybug Graphic Standards
With the parallel efforts or so many developers, we have made an effort in this release to standardize the means by which you interact with the components. This includes warnings for missing inputs and the ability to make either icons or text appear on the components as you wish (Hi Andres!). A full list of all graphic standards can be found here. If you have any thoughts or comments on the new standards, feel free to voice them here.
7 - Wet Bulb Temperature Now Available
Thanks to Antonello Di Nunzio - the newest member of the Ladybug development team, it is now possible to calculate wet bulb temperature with Ladybug. Antonello’s component can be found under the WIP tab and takes inputs of dry bulb temperature, relative humidity, and barometric pressure.
8 - New View Analysis Types
The view analysis component now allows for several different view studies in addition to the previous ‘view to test points.’ These include, skyview (which is helpful for studies of outdoor micro-climate), as well as spherical view and ‘cone of vision’ view, which are helpful for indoor studies evaluating the overall visual connection to the outdoors.
HONEYBEE
1 - Connection to THERM and LBNL Programs
With this release, many of you will notice that a new tab has been added to Honeybee. The tab “11 | THERM” includes 7 new components that enable you to export ready-to-simulate Lawrence Berkeley National Lab (LBNL) THERM files from Rhino/Grasshopper. THERM is a 2D finite element heat flow engine that is used to evaluate the performance of wall/window construction details by simulating thermal bridging behavior. The new Honeybee tab represents the first ever CAD plugin interface for THERM, which has been in demand since the first release of LBNL THERM several years ago. The export workflow involves the drawing of window/wall construction details in Rhino and the assigning of materials and boundary conditions in Grasshopper to produce ready-to-simulate THERM files that allow you to bypass the limited drawing interface of THERM completely. Additional components in the “11 | THERM” tab allow you to import the results of THERM simulations back into Grasshopper and assist with incorporating THERM results into Honeybee EnergyPlus simulations. Finally, two components assist with a connection to LBNL WINDOW for advanced modeling of Glazing constructions. Example files illustrating many of the capabilities of the new components can be found in there links.
THERM_Export_Workflow, THERM_Comparison_of_Stud_Wall_Constructions
Analyze_THERM_Results, Thermal_Bridging_with_THERM_and_EnergyPlus
Import_Glazing_System_from_LBNL_WINDOW, Import_LBNL_WINDOW_Glazing_Assembly_for_EnergyPlus
It is recommended that those who are using these THERM components for the first time begin by exploring this example file.
Tutorial videos on how to use the components will be posted soon. A great deal of thanks is due to the LBNL team that was responsive to questions at the start of the development and special thanks goes to Payette Architects, which allowed Chris Mackey (the author of the components) a significant amount of paid time to develop them.
2 - Electrical Lighting Components with Enhanced Capabilities for Importing and Manipulating IES Files
Thanks to the efforts of Sarith Subramaniam, it is now much easier and more flexible to include electric lighting in Honeybee Radiance simulations. A series of very exciting images and videos can be found in his release post.
You can find the components under WIP tab. Sarith is looking for feedback and wishes. Please give them a try and let him know your thoughts. Several example files showing how to use the components can be found here. 1, 2, 3.
3- Expanded Dynamic Shade Capabilities
After great demand, it is now possible to assign several different types of control strategies for interior blinds and shades for EnergyPlus simulations. Control thresholds range from zone temperature, to zone cooling load, to radiation on windows, to many combinations of these variables. The new component also features the ability to run EnergyPlus simulations with electrochromic glazing. An example file showing many of the new capabilities can be found here.
Dragonfly Beta
In order to link the capabilities of Ladybug + Honeybee to a wider range of climatic data sets and analytical tools, a new insect has been initiated under the name of Dragonfly. While the Dragonfly components are not included with the download of this release, the most recent version can be downloaded here. An example file showing how to use Dragonfly to warp EPW data to account for urban heat island effect can also be found here. By the next release, the capabilities of Dragonfly should be robust enough for it to fly on its own. Additional features that will be implemented in the next few months include importing thermal satellite image data to Rhino/GH as well as the ability to warp EPW files to account for climate change projections. Anyone interested in testing out the new insect should feel free to contact Chris Mackey.
And finally, it is with great pleasure that we welcome Sarith and Antonello to the team. As mentioned in the above release notes, Sarith has added a robust implementation for electric light modeling with Honeybee and Antonello has added a component to calculate wet bulb temperature while providing stellar support to a number of people here on the GH forum.
As always let us know your comments and suggestions.
Enjoy!
Ladybug+Honeybee development team
PS: Special thanks to Chris for writing most of the release notes!…
greatly appreciate it!!
You can write the number of the question and write your answer next to it, example:
1) a
2) c
3) a) Washington University in St. Louis
4) 2 weeks (1week+1week shipping)
5) 130
6) b
7) b
The survey questions are as follows:
1)
Did you 3D print before?
5)
How much did it cost (in dollars)?
a.
Yes, for a school project
a.
Between 20 & 50
b.
Yes, for a personal project
b.
Between 50 & 80
c.
Between 80 & 120
2)
Print size
d.
Please specify if otherwise: _____ dollars
a.
Between 2 & 6 cubic inches
b.
Between 6 & 12 cubic inches
6)
Do you think the price was expensive?
c.
Between 12 & 20 cubic inches
a.
Not at all
d.
Please specify if otherwise: ____cubic inches
b.
A little bit expensive
c.
Very expensive
3)
Where did you print your object?
a.
School
7)
Were you satisfied with the printed object?
b.
Outside school: _________________
a.
Yes, it was a great print without problems
b.
Not bad, some issues
4)
How long did it take to print?
c.
I was not satisfied, very bad quality
a.
___ days
b.
___ weeks
Thank you very much to all!!
PS: If you did many 3D prints, you can post multiple answers.
Wassef…