returned to GSA, it is solving. You might have to reset result scales using the GSA button.
Cheers,
Jon
Checking Input Data - this may take some time.
________________________________________
Data checks commenced at 23/08/2017 4:59:18 PM.
Checking input data for static analysis by GSS.
Shortest element (element 9) is 5 m long.Longest element (element 1) is 6 m long.
Data checks completed at 23/08/2017 4:59:18 PM. No errors or warnings found.
Analysis commenced at 23/08/2017 4:59:18 PM.
Analysis by Gss Static analysis
Initialising results modulesSolving for displacementsSolution statisticsSparse Parallel Direct 12 active nodes 14 active elements 2 analysis cases 24 degrees of freedom Minimum degree ordering 90 terms in stiffness matrix Maximum stiffness is 4.804e+009 at node 4 in direction z Minimum stiffness is 3.132e+008 at node 2 in direction yy Condition number of the stiffness matrix is ~ 5328. Maximum relative error in displacements will be 2.4e-10 percent. Factorization in 109 msSolving for element forces and reactionsCalculation completeAnalysis completed with no errors
Analysis completed at 23/08/2017 4:59:18 PM.Analysis time: 0.172 seconds
…
ted a picture of in your post. The reason is that sound has larger wavelengths than light.
With a light rendering model, energy can be said to reflect specularly, relative to their geometry, because the wavelength of light is inifinitesimally small relative to any object you might have modelled. With sound, energy may travel and reflect diffusely, or move around objects, depending on the scale of those objects. Think of the fundamental equation of frequency to wavelength - speed of sound = frequency X wavelength. Using that, you can see that a wave in the 125 hz octave is about as tall as a human being (or maybe a little taller) and would easily move around your body, not being reflected at all. A wave in the 1000 Hz. octave band is as big as your forearm, and might reflect specularly from your torso. A wave in the 4000 hz. octave band is about as long as your index finger, and might reflect off of your torso, or even your head.
Similarly, if you were to model the seats explicitly, it might be relatively accurate at very high frequencies (say 4000 hz. and above) but that is a very small part of the answer. Consensus in the field is that the most accurate way to model the seats is with a flat plane, raised to about shoulder height, and then with scattering coefficients applied to represent the varying effects of geometry on sound. I tend to use low coefficents below 250 hz. (say around 30%) and high coefficents above 250 Hz.(90%).
Absorption depends on the seat which was chosen. This is often a good area to use for a model calibration based on measured reverberation time.
Arthur…
ces are distorted (second). What is going on?
Surfaces in the second are a rhino cage edit of the surfaces in the first image. They were originally all closed polysrfs exploded just to input into grasshopper.
In the definition attached, each surface is compared to an original (its the small box in the far left of the top image) The point there is the ability to select for more than just the 6 faces of a cube, but find the closest match to more complicated inputs. In the second image, distorted surfaces are being compared to a distorted original.
If I have my math right, two parallel unitized normal vectors should have a dot product of 1, and the further away from 1 their dot product the further away from parallel, no? Why does it fail when I leave the comfy land of 90 degrees?…
Added by Peter Stone at 2:39pm on January 28, 2015
e to constrains, I HAVE to do it like this (I can't 3D print everything or opposite).
First
I have no idea how to make the panels, without so many duplicate Edges, Faces etc.
Second
I can't figure out how to align the triangle panels to fit in the construction, so it can be assembled ideally without glue. This problem is both conceptual (I can't figure out how to do it fiscally) and grasshoper-wise - I don't know how to organize data list and produce a global movement, so that the triangle parts do not intersect with each other, BUT intersect the 3d printed construction part (where they fit fix in or just fit and can be glued).
Triangles will be milled out from 3mm Plexiglas, BUT I will not have an option to mill at an angle, so only 90° edges.
3D printed parts will be executed by a high level production powder printer, so it should hold good.
Any ideas?
best,
cuki
…
File) 2. I have designed a curved Trichordal-Truss from one curve in Rhino.
The Truss is lying in the XY direction and the footer is placed on the zero point.
3. And now my problem:
I want to put the Truss-object on the feet, move 90°
(from the XY axis to Z axis, see sketch 1).
4. Then copy / move the truss to all 36-points of ellipse (see sketch 1).
5. Align the 36 trusses with the center of the triangle .
pointing at the center of the ellipse (see sketch 2).
6. Using a slider to change the position of the 36-Trusses at der ellipse.
Variable distance between Truss and ellipse (see sketch 3).
Thanks for you Answer.
Best regards
Noureddine…
multiply of variants from Galapagos, to have a chance for better analysis and comparability after. I also would like to use more then one solution in my design after.
In old topics i found kind of 3 solutions.
1.Change Galapagos to octopus ( what don t really want to do, i am kind of happy with Galapagos)
2. Use Slingshot! and MySQL Database ( it s look a little bit too complicated from the first view)
3. Use Colibri and Design Explorer Platform (looks kind of pretty way to solve my problem)
So i tried to add Colibri components to my definition , but have some mistake in the Colibri Aggregator after adding the Genome "An item with the same key already been added". I think it comes because for some steps i am using the "Gen Pool" and not a normal slider. Is it a way to connect Gen Pool and Colibri (i really prefer to have it, then a lot of sliders in some cases)?
And the second question (if i will get it solved with gen pool), could i somehow controll the recording process? For example i would likte to record only variants wit fitness over 90% or start recording just after 20. generation and record till the end?
I also opend for all other possibilities to reach the same goal (record/save/bake multiply variants from galapagos)
…
ius, like the image below. I have a string with all of the 8 radii in a group of data. I was using the Divide Surface command, but there are two problems. First, the resulting points have a tree structure shown in the screenshot below, with {8; 2; 3}. How do I assign radius so that the six holes on the same panel has the same radius? The second problem is, the divide surface command generates points along the edges, too, where I don’t need any holes. How can I get rid of them?
…
not working, then this can be a limitation of Honeybee, not the Terrain shading mask component.You can authenticate the mask shape by using the Udeuschle panorama generator (I used the following Trento coordinates: lat:46.066667, long:11.116667):
Sketchup has a similar plugin for Trynsys3D terrain shading masks.
I gave a reply on your upper questions in here, in component's release topic, so that it would be useful for others users too.
Actually I tried also to create the mask of the mountain using the topography I imported from Sketchup and the Ladybug Shading Mask II component. In this way the shading effect is well noticeable, but the process of creating the mask from such a complex geometry is very slow.
I can make a component which will automatically generate the topography of the local terrain, for a given latitude/longitude, but you will have to wait some time. I am currently doing some repairing around my house and cottage, and I do not have any spare time.Have in mind that depending on the configuration of you PC, you may not be able to have the terrain radius of up to 100 km. While Terrain Shading Mask component actually creates this terrain, it does not add it to the grasshopper document. In your case the terrain will be added to the grasshopper document which may crash Rhino depending on your PC configuration (for example it crashes Rhino on my PC).…
didn't look at it that closely), other than to say tree data structure is helping you and hurting you.
What I did to fix the file was work backwards. Looking at only the left panel you are trying to create 11 total planar surfaces from edge curves (8 curves per surface). That means you should be generating 11 of each type of curve so that you will have 88 total curves when you attempt to join them.
Tree data was in some cases giving you 121 of each type of curve (lists matching with tree structure...) so I worked backwards from your individual curves to flatten the inputs until ending up with only 11 (the expected number) of each type of curve.
…
icipate this summer, in the digital design build workshop, seeking to create an inventive collaborative environment.Aimed primarly at students, architects, urban designers, engineers, landscape architects.Guest invited tutor : Arian Hakimi Nejad (Iran)Profile: MAA 2010 - Architect/Urban Designer (IaaC-UPC, Barcelona, Spain)Workshop coordinator: Diana Nitreanu (RO)Profile: MAA 2010 - Architect/Urban Designer (IaaC-UPC, Barcelona, Spain)Official Rhino TrainerTRAINING OBJECTIVES:Presenting a set of innovative approaches and methodologies using Grasshopper.TOOLS: Grasshopper (primarly) and Rhinocerus (secondary)ATTENDANCE&COSTS:>Price 100 ron for 3days workshop/6h/day.>To book your seat send email to the address: diana.nitreanu@laboratorul.ro>The first 25 people to send email to the address above will get a seat.>To have your seat comfirmed, you must show up at the location above to receive a detailed schedule of the workshop.>When the workshop starts you must present yourself with the flyer that you will receive.REQUIREMENTS:>Bring your own laptop!>All the participants MUST have installed Rhinocerus and Grasshopper.>You can find details on www.rhino3d.com and grasshopper3d.comLOCATION:Mircea Vulcanescu st., no 27, sector 1, Bucharest, RomaniaFor further info or any questions, feel free to contact : 0722 86 06 87Free drinks, music, fun and a lot of new things to learn! :)IMPORTANT!THE WORKSHOP WILL BE HELD IN ENGLISH…