algorithmic modeling for Rhino
Hi i'm here again for asking help....is my frist time on Gh and i start working on it two weeks ago so i'm really sorry if this problem is stupid. On the attached file there is the error during the energy plus silulation and this is the error text:
Current document units is in Meters
Conversion to Meters will be applied = 1.000
Duplicate surface name! Name is changed to: Pelle_Sopra_Dup
Duplicate surface name! Name is changed to: Pelle_Nord_Dup
[1 of 8] Writing simulation parameters...
[2 of 8] No context surfaces...
[3 of 8] Writing geometry...
[4 of 8] Writing Electric Load Center - Generator specifications ...
[5 of 8] Writing materials and constructions...
[6 of 8] Writing schedules...
[7 of 8] Writing loads and ideal air system...
[8 of 8] Writing outputs...
...
... idf file is successfully written to : C:\Users\Personal\Desktop\TESI\x006\THOR001\EnergyPlus\THOR001.idf
Analysis is running!...
C:\Users\Personal\Desktop\TESI\x006\THOR001\EnergyPlus\eplusout.csv
...
...
Done! Read below for errors and warnings:
Program Version,EnergyPlus, Version 8.3.0-6d97d074ea, YMD=2016.01.05 20:08,IDD_Version 8.3.0
************* IDF Context for following error/warning message:
************* Note -- lines truncated at 300 characters, if necessary...
************* 160 ScheduleTypeLimits,
************* indicated Name=ANY NUMBER
************* Only last 2 lines before error line shown.....
************* 161 ANY NUMBER, !- name
************* 162 ScheduleTypeLimits, !-
** Severe ** IP: IDF line~162 Invalid Number in Numeric Field#1 (Lower Limit Value), value=SCHEDULETYPELIMITS, in SCHEDULETYPELIMITS=ANY NUMBER
************* IDF Context for following error/warning message:
************* Note -- lines truncated at 300 characters, if necessary...
************* 258 ScheduleTypeLimits,
************* indicated Name=ANY NUMBER
************* Only last 2 lines before error line shown.....
************* 259 ANY NUMBER, !- name
************* 260 ScheduleTypeLimits, !-
** Severe ** IP: IDF line~260 Invalid Number in Numeric Field#1 (Lower Limit Value), value=SCHEDULETYPELIMITS, in SCHEDULETYPELIMITS=ANY NUMBER
** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
** Severe ** IP: Possible incorrect IDD File
** ~~~ ** IDD Version:"IDD_Version 8.3.0"
** ~~~ ** Version in IDF="8.3.0" not the same as expected="8.3"
** ~~~ ** Possible Invalid Numerics or other problems
** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
...Summary of Errors that led to program termination:
..... Reference severe error count=3
..... Last severe error=IP: Possible incorrect IDD File
************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 3 Severe Errors; Elapsed Time=00hr 00min 0.30sec
thanks for any help
Lhor
Tags:
Replies are closed for this discussion.
Hi Lhor,
Your file works fine on my machine. The error seems to be because of an old EP library on your system. I updated your file. Can you open the file and see if it works fine?
In case it gave you the same error. Close Grasshopper and Rhino and follow these steps:
1. Go to Ladybug working folder. You can find it from the output of Ladybug_ladybug component.
2. There should be a file named "OpenStudioMasterTemplate.idf". Open the file with any text editor and see if the first line is ! {"version" : "2015.11.02.02.00"}
3. If the first line is the same attach the file to this discussion so I can give it a try.
4. Otherwise delete the file and open Rhino and Grasshopper and run your file. It should download an updated version of idf file which should solve the problem.
One request! Please choose an appropriate topic for your discussions. "Error again" is not the most informative option! Here is a good read about how to ask a good question: (http://stackoverflow.com/help/how-to-ask).
For a person who has started Grasshopper two weeks ago you had a great progress. Congratulations!
i can't see your updated file.
Thanks for all and next time i pay more attention on create a correct topic :)
Lhor
oops! Here is the file.
Welcome to
Grasshopper
Added by Parametric House 0 Comments 0 Likes
Added by Parametric House 0 Comments 0 Likes
Added by Parametric House 0 Comments 0 Likes
Added by Parametric House 0 Comments 0 Likes
Added by Parametric House 0 Comments 0 Likes
© 2024 Created by Scott Davidson. Powered by