"Hi David,
I have exactly the same error in trying to split surface. I'm using the latest GH 0.9.0014 for Rhino 4. Wondering if you have found a solution to it yet.
Thanks a lot!"
generative modeling for Rhino
-
Cheryl Lee
- Female
- Singapore
- Singapore
- Blog Posts
- Discussions (4)
- Events
- Groups (3)
- Photos
- Photo Albums
- Videos
Cheryl Lee's Discussions
Some Galapagos & DIVA simulation questions
8 Replies
Hi. I'm using Galapagos and DIVA for my architecture thesis project. And I hope I could get some help.In my project, I am trying to use Galapagos to maximize the amount of daylight in a high-rise…Continue
Started this discussion. Last reply by Michael Makris Jan 28.
Cheryl Lee's Page
Latest Activity
Michael Makris replied to Cheryl Lee's discussion Some Galapagos & DIVA simulation questions"Hey Michal. Thanks for the reply, but I think you're answering a different question. I'm asking about how to understand the actual Galapagos interface, i.e. the orange graph that Galapagos creates. I'm confused as to what the…"
Cheryl Lee replied to Cheryl Lee's discussion Some Galapagos & DIVA simulation questions"Hi! Sorry, I must have missed all of this.
Regarding the evolutionary solver, leaving it for hours to run did do the trick, especially with the simulations it did take pretty long.
Regarding saving the outputs, I found this which is pretty…"
David Rutten replied to Cheryl Lee's discussion Some Galapagos & DIVA simulation questions"
means that a new offspring genome was created which was similar to a genome already once computed (Galapagos never calculates the same genome twice). When this happens a lot it means one of two things:
The entire population is highly…"
Michal Dengusiak replied to Cheryl Lee's discussion Some Galapagos & DIVA simulation questions"Hi, In this case above was quite simple. You can see on the left side 4 and right 3 options. Those are the values of slider left (percentage of glazing), right (type of glass). I did just simple multiplication of values and looking for minimum.…"
Michael Makris replied to Cheryl Lee's discussion Some Galapagos & DIVA simulation questions"Hey Michael. I'm new to Galapagos. How does you know how to read your results/get your results from Galapagos? IE how do I learn what all the graphics in that screen mean and how do I save the genome data for analysis?"
Michal Dengusiak replied to Cheryl Lee's discussion Some Galapagos & DIVA simulation questions"Results file"
Michal Dengusiak replied to Cheryl Lee's discussion Some Galapagos & DIVA simulation questions"Hi,
I run it overnight and here is summary:
1. I noticed that is good to make number more round..In my case I did Integer
2. Galapagos has finished after 50 steps and did run simulation for each pool of options
3. However I am not sure that in…"
Michal Dengusiak replied to Cheryl Lee's discussion Some Galapagos & DIVA simulation questions"Hi,
I just run my first simulation and this are my comments and questions and your reply.
Reply
(a) you have to allow Evolutionary solver for some time in order to see the first set of results. In your case which seems to be…"
Cheryl Lee posted a discussionSome Galapagos & DIVA simulation questions
Hi. I'm using Galapagos and DIVA for my architecture thesis project. And I hope I could get some help.In my project, I am trying to use Galapagos to maximize the amount of daylight in a high-rise building floor plan. This is done by minimizing the number of areas with less than a certain amount of lux. To simulate the daylight level or illuminance of the floor plan, DIVA was used.Below is what my grasshopper definition looks like:…See More
Cheryl Lee joined Mostapha Sadeghipour's group
Ladybug
Ladybug is a free and open source environmental plugin for Grasshopper to help designers create an environmentally-conscious architectural design. Ladybug allows you to: import and analyze standard weather data in Grasshopper; draw diagrams like Sun-path, wind-rose, radiation-rose, etc; customize the diagrams in several ways; run radiation analysis, shadow studies, and view analysis for your design inside Grasshopper!Ladybug only works on Rhino 5.0. Unfortunately, there is no version for Rhino…See More
Cheryl Lee replied to Henners's discussion Beginners Question in the group Kangaroo"Hi,
I'm doing an architectural project for school and trying to create tensile structures.
Could you help in sharing a demo file for something like what you did here? A kangaroo file with mixed elements such as struts, tension cables and a…"
Profile Information
- Company, School, or Organization
- NUS
Comment Wall
- No comments yet!
Translate
Search Grasshopper
Photos
Videos
© 2013 Created by Scott Davidson.
Powered by
