as one element.
Thank you
Comment by karamba on October 7, 2014 at 11:27pm
Hello Patricio, divide the beams in such a way that each boundary vertex of the shell becomes an endpoint of a beam segment.
Best, Clemens
Comment by Llordella Patricio on October 8, 2014 at 8:30amDelete Comment
Hi Clemens,
I did what you suggested but now assemble element doesn´t work properly. Could you please tell me how to fix it? Thanks in advance, Patricio
8-10-14losa%20cadena.gh
Comment by karamba on October 8, 2014 at 11:59am
Hi Patricio, if you flatten the 'Elem'-input at the 'Assemble'-component the definition works. The triangular shell elements have linear displacement interpolations whereas the beam deflections are exact. In order to get correct results you should refine the shell mesh.
Best, Clemens
Comment by Llordella Patricio on October 9, 2014 at 8:35amDelete Comment
Hello, succeeds in creating the mesh to the slab, and built the beam segment, but when I see the deformations are not expected because the beam is deformed as the slab.
Thanks for the help
PS: maybe I'm using the program for a type of structure that is not the most appropriate, as I saw in the examples of other structures. But this type of structure is that students taught
best regards
Patricio
9-10-14%20Example%201.gh
Comment by karamba on October 9, 2014 at 10:46am
You could use the 'Mesh Edges'-component to retrieve the naked edges and turn them into beams - see attached file:91014Example1_cp.gh
Best regards,
Clemens
Comment by Llordella Patricio on October 15, 2014 at 3:41pmDelete Comment
Dear clemens
I was doing a rough estimate of the deformation, and I can not achieve the same result with Karamba. When I make a rough estimate of the result with Karamba beams and mine are very similar, I think the problem is when I connect the shell, because there are no similar results.
I sent the GH file, and an image of the calculation
The structure is concrete The result I get is 0.58cm
thank youPatricio
15-10-14%20Example.gh
Comment by karamba yesterday
Dear Patricio,
try to increase the number of shell elements. As mentioned in the manual they are linear elements. A mesh that is too coarse leads to a response which is stiffer than the real structure.
Best,
Clemens
…
is also takes place in own system. However, this action can be also carried out successfully by a foreign reference, if this considers the focused system as own. Hence, these two criteria are considered in my reflexions, to make your criticism handier for me.
First the question must be put up, how is it in your case? Of friendly manner you answer this question perpetually with the statement that you are not a partial of the system of the architecture.
Furthermore the question would be appropriate, whether an external reference (eg CAD) determined architecture. This can be answered with no, because determining and influencing are different things.
Because you stress now your criticism as a foreign criticism, within the architecture the assuption must be put up, that this criticism is not unusual new on the one hand (because this condition were also in other times like that, and presumably also always so remain) and further more a lack of goodwill in your criticism comes to light, which perhaps distinguishes an external reference.
Based on your critique, it would be also desirable in the system of the architecture if the academic rules become satisfyingly followed, even if this is no guarantor for good academic works. Nevertheless, there is an aspect which at least tolerates the evident lack in the Interdiziplinarität of the architecture. This is the classical and still valid determination of the architecture, presumably regulates not only the actions of the architects, but also those who want to become it.
Many who stand in your criticism (the students, as well as the teachers, ... ), live in the awareness that architecture is a profession that combines as many areas around the topic of Building, and the architect is even only one dilettante among the external specialists. In this determination dilettantism is revalued rather positively, because this state the architects enables to assess the facets of a complicated building project better and to form thereby the whole result positively. To be a good architect, you should have circumspect specialists around yourself. And exactly this knows the system of the architecture, because "THE ARCHITECT" helps himself with the logic of other systems (to repair on the one hand his own deficits), and to create an artificial complexity, which ultimately aims to be the complexity of human beeing.
Here "THE ARCHITECTS" becomes a quality-spoken, which currently seems the external reference (CAD, BIM) would like to take claim for themselves.
........
If would not thought about it, this might be helpful:http://www.amazon.com/The-Alphabet-Algorithm-Writing-Architecture/dp/0262515806/ref=sr_1_1?ie=UTF8&qid=1376920450&sr=8-1&keywords=mario+carpo"Finally, I’d like to restate my criticisms in general terms. If we are serious about moving architecture and urbanism away from purely artistic considerations and into a more rational arena, there has never been a better time than now. All of us have access to immense computational power which can be applied to problems that have been —until quite recently— intractable. But of course the garbage-in-garbage-out adage holds true; computation can be used to generate large amounts of complexity, but complexity does not equal worth. The only time when it makes sense to invoke computation in the design process is when there is some relevant data that needs to be computed" (David Rutton)I want to make it short, and just ask a few questions, and hope that the following questions are relevant also for you, and not be considered outside your system. i think that the weighting to such questions seem to be more valuable, not for the architects.1. What is wrong from a pure artistic intention?2. What is any sense in purely architectural discourse?3. strictly looked, can be determined sense generally in a purely architectural discourse?4. What is purely architectural discourse?5. What is Funktionalismus or Rationalismus without philosophical support? 6. Would not be the pure functional fulfilment empty ? 7. Would be not a critical position on the promise of purely rational algorithms applied?…
what they really mean by that, as in what buttons to push, so I assume it's a Windows Path entry?
2.) Modify PATH
Add the install location on the path, this is usually: C:\Program File\IronPython 2.7
But on 64-bit Windows systems it is: C:\Program File (x86)\IronPython 2.7
As a check, open a Windows command prompt and go to a directory (which is not the above) and type:
> ipy -V PythonContext 2.7.0.40 on .NET 4.0.30319.225
Tutorial on setting a Windows environmental variable (path):
http://www.computerhope.com/issues/ch000549.htm
But this fails to point out that path contains many entries already separated by semicolons so if I merely add a new variable called "path" it's likely that I will destroy existing program function. There's no info on how to just tack on another entry, and the Windows 7 edit box doesn't even show the whole collection, but one item (!), so I copied the existing path into a text editor to see the whole collection successfully and added the C:\Program Files (x86)\IronPython 2.7 entry after an added semicolon, correcting for an Enthought page typo of no 's' on the end of "Program Files". I also checked the others and many pointed to old missing directories so I deleted those entries.
...and the test fails and "ipy" is not recognized as a command, even though the path now shows up using "path" in the Windows CMD window, that is if I copy all by right clicking and pasting the stuff into a text editor to really view it all. I can run it from the source directory just fine.
The rabbit hole was indeed deep. Using the Task Manager (control-alt-delete) to kill Explorer and then Run in the menu to restart "Explorer," along with restarting the Windows CMD window however, worked. I can now invoke Iron Python ("ipy") via command line from any directory. For the "path" I edited path in the System Variables and not the User Variables. No, you don't have to type that whole crazy line above just to test the path variable, just "ipy" (and control-Z to quite IronPython) in the CMD window invoked by typing "cmd" into the Start menu search box.
From the CMD line this step did work fine:
3.) ironpkg
Bootstrap ironpkg, which is a package install manager for binary (egg based) Python packages. Download ironpkg-1.0.0.py and type:
> ipy ironpkg-1.0.0.py --install
Now the ironpkg command should be available:
> ironpkg -h(some useful help text is displayed here)
But of course Step 4 fails, giving pages of what seem to be error messages;
C:\Users\Nik>ironpkg scipy
Traceback (most recent call last):
File "C:\Program Files (x86)\IronPython 2.7\lib\site-packages\enstaller\utils.
py", line 92, in write_data_from_url
File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 126, in urlo
pen
File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 397, in open
File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 509, in http
_response
...
Why can't I just download Numpy as a normal file and thus also have it easy for other users to install it when they use my scripts? This is just crazy and lazy. The Enthought developer has turned this into a computer game, with a missing registration link and then the last step spits out errors with utterly no information on how to fix it manually.
This Step 4 error is covered here:
http://discourse.mcneel.com/t/trying-to-import-numpy-in-rhino-python-but-im-getting-this-error-cannot-import-multiarray-from-numpy-core/12912/16…
Added by Nik Willmore at 2:36pm on October 11, 2015
you may know, PCS (from now I will call polar coordinate system with PCS, and cartesian one with CCS) describes point position with 2 values (like x and y in CCS) which are r and theta(r,theta). r is for distance from PCS center, theta is angular dimension which is in 0 to 360 or 0 to 2*pi domain.
To hark back to David's guide line - here it is replaced with guide circle.
Why to sort points like this ? As usual, one image tells more...
Here is logic behind all this stuff :
Find an average point of all given points*
Search for furthest point from an average point*
Create a circle with center at average point and radius = distance from average point to furthest point*
*Steps 1-3 can be replaced with custom hand-made circle, I decided to automate it that way.
For each point find closest point on circle - this will be used for finding theta value
For each point find distance to average point - this is r value
To overcome problem with same theta (t) values (like same x values in CCS), instead of multiplying by 1000, we will use a new create set component. This component creates set of integers, each one representing one unique input value. So if points A, B, C, D, E are (r,theta) :
A (1, 30)
B (2, 30)
C (3, 30)
D (1, 45)
E (1, 60)
Then create set will output list of integers = 0,0,0,1,2 (same theta for A, B, C other theta for D and E). Now its getting really easy - remap r values to domain 0 to 0.5 (or any less then 1), and add integers from create set component to remapped r values.
7. So what we have now is list of floating point numbers : A=0, B=0.25, C=0.5, D=1, E=2
Profit of remapping is that r values will never affect integers representing theta values - and all the information is stored in one floating point number ! By sorting these values we will obtain proper order of points - to complete this, we need to sort points parallel with values.
What's really cool about polar sorting - there could be any amount of points, but polyline connecting all of them will never self-intersect. Probably there is some relation with 2d convex hull.…
- nickname is rather the best approach - and not on active group, but that's irrelevant anyway).
Step back (assuming that you are talking about the "Tens_from_random_blah_blah" definition):
1. Engineering is the art of demystifying (or we are promising that anyway, he he). This means that you start defining (better: outlining) some topology for things based on some "generic" rules (like the ones applied for the masts,cables,cones etc etc). These things are kept in some kind of structure (Lists, DataTrees etc). Things are few in 99.99999% of cases (i.e. : even the biggest membrane "module" has, say, 20-50 masts per "module").
2. Then ... handling things "individually" (mostly modifying) becomes the most critical part. See this (an x "possible" solution by combining a myriad of "options" : a no cones membrane solution, in plain English):
3. But the above is impossible (for more than obvious reasons). You should deploy masts in some high/low sequence in order to achieve some meaningful convex/concave formation that could work.
4. This "works" : 5. This doesn't:
6. This works partially (the formation at the back is "flat" == undo able):
7. This is utterly kitsch (and faulty as the case6 - the back portion):
So it's quite obvious that without a (quite complex) capability to individually control things (in this occasion : mast heights) the whole definition is a waste of computer time. Additionally the more the solution is "demystified" (some curve is defined, some random points are created, some masts are in place, some cables appear etc etc) the more additional constrains are required in order to "narrow" the possibilities (In plain English : sliders should control other sliders as regards their min/max values, true/false, you/me etc etc).
Remember that we are talking about ONE (mast height) out of a myriad things that you should control "manually" (it's utterly pointless to mastermind some kind of "generic" rules - or use naive attractors etc etc) .You'll see the difference when I'll completely reform the definition by adding individual control upon anything.
PS: what about the blocks? (the real life stuff that actually make any solution possible). Can you imagine a 2nd set of "restrictions" imposed by "a child to his parent"? (Assembly/Component modeling , that is).
more soon
…
uick answers. Below you will find some suggestions, but don't think of them as rules and especially don't think of them as guarantees.
1. Choose a descriptive title for your post
Don't call your question "Help!" or "I have a problem" or "Deadline tonight!", but actually describe the problem you are having.
2. Be succinct but clear in your wording
People need to know some details about your problem in order to understand what sort of answers would satisfy you, but nobody cares about how angry your boss or how bad your teacher or how tight your deadline is. Talk about the problem and only the problem. If you don't speak English well, you should probably post in your native language as well as providing a Google Translation of your question.
3. Attach minimal versions of all the relevant files
If you have a GH/GHX file you have a question about, attach it to the post. Don't expect that people will recreate a file based on a screen-shot because that's a lot of pointless work. It's also a good idea to remove everything non-essential from a GH file. You can use the 'Internalise Data' menu option to cut everything to the left of a parameter:
If you're importing curves or Breps or meshes from Rhino, you can also internalise them so you won't have to post a 3DM file as well as a GH file. If you do attach large files, consider zipping them first. Do not use RAR, Ning doesn't handle it.
It is especially a good idea to post files that don't require any non-standard components if at all possible. Not everyone has Kangaroo or Hoopsnake or Geco installed so if your file relies on those components, it might not open correctly elsewhere.
4. Include a detailed image of the GH file if it makes sense
If your question is about a specific (group of) components, consider adding a screenshot of the file in the text of the post. You can use the Ctrl+Shift+Q feature in Grasshopper to quickly create nice screenshots with focus rectangles such as this:
5. Include links to online resources if possible
If you have a question about Schwarz Minimal surfaces, please link to a website which talks about these.
6. Create new topics rather than continuing old ones
It's usually better to start a fresh question, even if there's already a discussion that kinda sorta tangentially touches upon the same issue. Please link to that discussion, but start anew.
7. This is not a 'do my work for me' group
Many of us like to help, but it's good to see effort on our part being matched by effort on your part. Questions in the form of 'I need to do X but cannot be bothered to try and learn the software' will (and should) go unanswered.
7b. Similarly, questions in the form of 'How do I quickly recreate this facade that took a team of skilled professionals four months to figure out?' have a very low success rate.
--
David Rutten
Lead Grasshopper Development
Robert McNeel & Associates…
Added by David Rutten at 12:58pm on October 1, 2013
2: https://vimeo.com/107502226
------------------------------------------------------------------------------------------------
Hi all,
1. Chris, Chien Si and I will present Ladybug and Honeybee at IBSA-USA NYC this Thursday (August 21st). The presentation will include some of the latest developments that we are working on. If you are interested to know more about some of the new developments and see some of the workflows and you are around New York then just stop by. If can't attend in person you can still watch the presentation online. Check the links below. (Make sure to register by Wednesday if you are attending in person.)
2. We would like to show some of the works that you have done with Honeybee and Ladybug during the presentation so if there is anything that you think is interesting and can be presented publicly send it to us at thisisladybug@gmail.com or just post it here. Make sure to let us know who do you want us to credit the image.
3. That's it for now. I copy the information about the presentation below and hope to see some of you there. Thanks for your help and support.
Cheers,
Mostapha
IBPSA-USA New York Regional Chapter presents:
Parametric Modeling Tools | Ladybug and Honeybee
Location: Thornton Tomasetti, 44 East 27th street (between Madison and Park)
Date & Time: Thursday, August 21, 2014 - 6:00-7:30 PM.
6:00-6:30 PM Networking
6:30-7:30 PM Ladybug and Honeybee
Mostapha Sadeghipour Roudsari, Thornton Tomasetti
Chris Mackey, MIT
Chien Si Harriman, Terabuild
7:30-7:45 PM Q & A
Click here to register**: https://attendee.gotowebinar.com/register/6507378565592582402
**Please register at least a day in advance if you wish to attend in person
Descriptions
Ladybug + Honeybee
Ladybug and Honeybee are open source environmental plugins for Grasshopper that help architects and engineers create an environmentally-conscious architectural design.
Ladybug imports standard EnergyPlus Weather files (.EPW) into Grasshopper and provides a variety of 3D interactive graphics to support the decision-making process during the initial stages of design. The plugin also provides further support for designers as they test their initial design options with radiation, sunlight-hour, and shading analyses. Integration with Grasshopper allows for an almost instantaneous feedback and, since the plugin runs within the design environment, the information and analyses are interactive.
Honeybee connects Grasshopper3D to EnergyPlus, Radiance, Daysim and OpenStudio for building energy and daylighting simulation. The Honeybee project intends to make many of the features of these simulation tools available in a parametric way. Just as users have made changes to geometry for years in Grasshopper, now users can parameterize system types, zoning schemes, schedules of operation, daylight sensor placement and controls - all of the “hardcore” simulation parameters that have never been exposed to parametric modeling tools.
https://www.facebook.com/LadyBugforGrasshopper http://www.grasshopper3d.com/group/ladybug
…
ting.
Thanks
Rania
** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
** Warning ** Version: in IDF="'8.2.7'" not the same as expected="8.2"
** Warning ** ManageSizing: For a zone sizing run, there must be at least 1 Sizing:Zone input object. SimulationControl Zone Sizing option ignored.
** Warning ** ManageSizing: For a plant sizing run, there must be at least 1 Sizing:Plant object input. SimulationControl Plant Sizing option ignored.
************* Testing Individual Branch Integrity
************* All Branches passed integrity testing
************* Testing Individual Supply Air Path Integrity
************* All Supply Air Paths passed integrity testing
************* Testing Individual Return Air Path Integrity
************* All Return Air Paths passed integrity testing
************* No node connection errors were found.
************* Beginning Simulation
************* Simulation Error Summary *************
** Warning ** The following Report Variables were requested but not generated
** ~~~ ** because IDF did not contain these elements or misspelled variable name -- check .rdd file
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR TOTAL COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR TOTAL HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=CHILLER ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=BOILER HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=FAN ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR LATENT HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR LATENT COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR SENSIBLE HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR SENSIBLE COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=SYSTEM NODE MASS FLOW RATE, Frequency=Hourly
************* Key=*, VarName=SYSTEM NODE TEMPERATURE, Frequency=Hourly
************* Key=*, VarName=SYSTEM NODE RELATIVE HUMIDITY, Frequency=Hourly
************* There are 3 unused schedules in input.
************* There are 5 unused week schedules in input.
************* There are 13 unused day schedules in input.
************* Use Output:Diagnostics,DisplayUnusedSchedules; to see them.
*************
************* ===== Recurring Surface Error Summary =====
************* The following surface error messages occurred.
*************
************* Base Surface does not surround subsurface errors occuring...
************* Check that the GlobalGeometryRules object is expressing the proper starting corner and direction [CounterClockwise/Clockwise]
*************
** Warning ** Base surface does not surround subsurface (CHKSBS), Overlap Status=No-Overlap
** ~~~ ** The base surround errors occurred 1 times.
** ~~~ ** Surface "839A5ADACCE44BC0AF00_GLZP_31" misses SubSurface "839A5ADACCE44BC0AF00_GLZP_31_GLZ_31"
** Warning ** Base surface does not surround subsurface (CHKSBS), Overlap Status=Partial-Overlap
** ~~~ ** The base surround errors occurred 1 times.
** ~~~ ** Surface "839A5ADACCE44BC0AF00_GLZP_34" overlaps SubSurface "839A5ADACCE44BC0AF00_GLZP_34_GLZ_34"
*************
** ~~~ ** The base surround errors occurred 2 times (total).
*************
************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
************* EnergyPlus Sizing Error Summary. During Sizing: 2 Warning; 0 Severe Errors.
************* EnergyPlus Completed Successfully-- 7 Warning; 0 Severe Errors; Elapsed Time=00hr 07min 35.94sec…
nd improvements. Many of the new features and components announced in the last release have become stable and have emerged from their WIP section. Additionally, after two years of work, we are happy to announce that we finally have full support of an OpenStudio connection within Honeybee, which has ushered in a whole host of new features, notably the modelling of detailed HVAC systems. As always you can download the new release from Food4Rhino. Make sure to remove the older version of Ladybug and Honeybee and update your scripts.
LADYBUG
1 - Solar Hot Water Components Out of WIP
After much beta-testing, bug-fixing, and general development, all of the Photovoltaic and Solar Hot Water components are now fully out of WIP! The main component is based on a Chengchu Yan's publication. Components have been added to Ladybug thanks to the efforts of Chengchu Yan and Djordje Spasic.. See Djorje’s original release post of the solar hot water components for more information on the components that just made it out of WIP.
2 - New Terrain Shading Mask Released in WIP
In addition to Djordje’s prolific addition of renewable energy components, he has also contributed a widely-useful component to generate terrain shading masks, which account for the shading of surrounding mountains/terrain in simulations. While initially added to assist the solar radiation radiation and renewable energy components, the component will undergo development to optimize it for energy and daylight simulations over the next few months. Another new component called Horizon Angles can be used to visualize and export horizon angles. You can test them out now by accessing them in the WIP section. For more information, see Djordje’s release post on the GH forum here.
3 - New Mesh Selector Component
After realizing that the Optimal Shade Creator component has applications to a whole range of analyses, it has now been re-branded as the Mesh Selector and has been optimized to work easily with these many analyses. Specifically, the component selects out the portion of a mesh that meets a given threshold. This can be the portion of a shade benefit analysis meeting a certain level of shade desirability, the portion of a radiation study meeting a certain level of fulx, the portion of a daylight analysis meeting a certain lux threshold, and much more!
4 - Solar Adjusted Temperature Now Includes Long Wave Radiation
Thanks to a question asked by Aymeric and a number of clarifications made by Djordje Spasic, the Solar Adjusted Temperature component now includes the ability to account for long-wave radiative loss to the sky in addition to it original capability to account for short wave radiation from the sun. As such, the component now includes all capabilities of similar outdoor comfort tools such as RayMan. The addition of this capability is also paralleled by the addition of a new horizontalInfraredRadiation output on the ImportEPW component. See the updated solar adjusted example file hereto see how to use the component properly.
5 - Support for both Log and Power Law Wind Profiles
In preparation for the future release of the Butterfly CFD-modelling insect, the Ladybug Wind Profile component now includes the option of either power law or log law wind profiles, which are both used extensively in CFD studies. Thanks goes to Theodoros Galanos for providing the formulas!
6 - New Radiant Asymmetry Comfort Components
Prompted by a suggestion from Christian Kongsgaard, Ladybug now includes components to calculate radiant asymmetry discomfort! For examples of how to use the components see this example file for spatial analysis of radiant asymmetry discomfort and this example for temporal analysis.
7 - Pedestrian Wind Comfort Component Released in WIP
In preparation for the impending release of the butterfly CFD-modelling insect, Djordje Spasic with assistance from Liam Harrington has contributed a component to evaluate outdoor discomfort and pedestrian safety. The component identifies if certain areas around the building are suitable for sitting, building entrances-exits, window shopping... based on its wind microclimate. Dangerous areas due to high wind speeds are also identified.You can check it out now in the WIP section.
HONEYBEE
1 - New HVAC Systems and Full OpenStudio Support
After a significant amount of development on the part of the OpenStudio team and two years of effort on the part of LB+HB developers, we (finally!) have full support for an OpenStudio connection within Honeybee. By this, we mean that any energy simulation property that can be assigned to a HBZone will be taken into account in the simulation run by the OpenStudio component. The connection to OpenStudio has brought with it several new capabilities. Most notably, you can now assign full HVAC systems and receive energy results in units of electricity and fuel instead of simple heating and cooling loads. This Honeybee release includes 14 built-in HVAC template systems that can be assigned to the zones, each of which can be customized:
0. Ideal Air Loads 1. PTAC | Residential 2. PTHP | Residential 3. Packaged Single Zone - AC 4. Packaged Single Zone - HP 5. Packaged VAV w/ Reheat 6. Packaged VAV w/ PFP Boxes 7. VAV w/ Reheat 8. VAV w/ PFP Boxes 9. Warm Air Furnace - Gas Fired 10.Warm Air Furnace - Electric 11.Fan Coil Units + DOAS 12.Active Chilled Beams + DOAS 13.Radiant Floors + DOAS 14.VRF + DOAS
Systems 1-10 are ASHRAE Baseline systems that represent much of what has been added to building stock over the last few decades while systems 11-14 are systems that are commonly being installed today to reduce energy use. Here is an example file showing how to assign these systems in Honeybee and interpret the results and here is an example showing how to customize the HVAC system specifications to a wide variety of cases. To run the file, you will need to have OpenStudio installed and you can download and install OpenStudio from here.
In addition to these template systems within Honeybee, the OpenStudio interface includes hundreds of HVAC components to build your own custom HVAC systems. OpenStudio also has a growing number of user-contributed HVAC system templates that have been integrated into a set of scripts called "Measures" that you can apply to your OpenStudio model within the OpenStudio interface. You can find these system templates by searching for them in the building components library. Here is a good tutorial video on how to apply measures to your model within the OpenStudio interface. Honeybee includes a component that runs these measures from Grasshopper (without having to use the OpenStudio interface), which you can see a demo video of here. However, this component is currently in WIP as OpenStudio team is still tweaking the file structure of measures and it is fairly safe to estimate that, by the next stable release of Honeybee, we will have full support of OpenStudio measures within GH.
2 - Phasing Out IDF Exporter
With the connection to OpenStudio now fully established, this release marks the start of a transition away from exporting directly to EnergyPlus and the beginning of Honeybee development that capitalizes on OpenStudio’s development. As such THIS WILL BE THE LAST STABLE RELEASE THAT INCLUDES THE HONEYBEE_RUN ENERGY SIMULATION COMPONENT.
The Export to OpenStudio component currently does everything that the Run Energy Simulation component does and, as such, it is intended that all GH definitions using the Run Energy Simulation component should replace it with the OpenStudio component. You can use the same Read EP Result components to import the results from the OpenStudio component and you can also use the same Energy Sim Par/Generate EP Output components to customize the parameters of the simulation. The only effective difference between the two components is that the OpenStudio component enables the modeling of HVAC and exports the HBZones to an .osm file before converting it to an EnergyPlus .idf.
For the sake of complete clarity, we should state that OpenStudio is simply an interface for EnergyPlus and, as such, the same calculation engine is under the hood of both the Export to OpenStudio component and the Run Energy Simulation component. At present, you should get matching energy simulation results between the Run Energy Simulation component and a run of the same zones with the OpenStudio component (using an ideal air system HVAC).
All of this is to say that you should convert your GH definitions that use the Run Energy Simulation component to have the OpenStudio component and this release is the best time to do it (while the two components are supported equally). Additionally, with this version of Honeybee you will no longer need to install EnergyPlus before using Honeybee and you will only need to install OpenStudio (which includes EnergyPlus in the install).
3 - New Schedule Generation Components
Thanks to the efforts of Antonello Di Nunzio, we now have 2 new components that ease the creation of schedule-generation in Honeybee. The new components make use of the native Grasshopper “Gener Pool” component to give a set of sliders for each hour of the day. Additionally, Antonello has included an annual schedule component that contains a dictionary of all holidays of every nearly every nation (phew!). Finally, this annual schedule component can output schedules in the text format recognized by EnergyPlus, which allows them to be written directly into the IDF instead of a separate CSV file. This will significantly reduce the size of files needed to run simulations and can even reduce the number of components on your canvas that are needed to add custom schedules. For more information, see Antonello’s explanatory images here and Antonello's example file here. You can also see a full example file of how to apply the schedules to energy simulations here.
4 - EnergyPlus Lookup Folder, Re-run OSM/IDF, and Read Result Dictionary
With the new capabilities of OpenStudio, we have also added a number of components to assist with managing all of the files that you get from the simulation. In particular, Abraham Yezioro has added a Lookup EnergyPlus Folder component that functions very similarly to the Lookup Daylight Folder component. This way, you can run an Energy simulation once and explore the results separately. Furthermore, we have added components to Re-Run OpenStudio .osm files or EnergyPlus .idf files within Grasshopper. These components are particularly useful if you edit these .osm or .idf files outside of Honeybee and want to re-run them to analyze their results in Grasshopper. Lastly, a component has been added to parse the .rdd (or Result Data Dictionary) file that EnergyPlus produces, enabling you to see all of the possible outputs that you can request from a given simulation.
5 - Electric Lighting Components Out of WIP
After Sarith Subramaniam’s initial components to model electric lights with Radiance in the last release, we are happy to report that they have been fully tested and are out of WIP. Improvements include support for all types of light fixture geometries and the ability to use the components in a more “Grasshoppery” list-like fashion. See Sarith’s original release post for more information and several example files showing how to use the components can be found here. 1 , 2 , 3 .
6 - Improvements to THERM Components
A number of bug fixes and improvements have been made to the THERM components in order to make their application more flexible and smooth. Special thanks is due to Derin Yilmaz , Mel King , Farnaz , Ben (@benmo1) , and Abraham Yezioro for all of the great feedback in the process of improving these components.
7 - HBObject Transform Components
After some demand for components that can ease the generation of buildings with modular zone types, two components to transform HBObjects with all of their properties have been added to the 00 | Honeybee section. The components allow you to produce copies of zones that are translated or rotated from the original position.
8 - Comfort Maps Supports PET and Integration of CFD Results
Thanks to the addition of the ‘Physiological Equivalent Temperature’ (PET) component by Djordje Spasic in the last stable release, it is now possible to make comfort maps of PET with Honeybee. PET is particularly helpful for evaluating OUTDOOR comfort with detailed wind fields at a high spatial resolution. As such, the new PET recipe has also been optimized for integration with CFD results. The windSpeed_ input can now accept the file path to a .csv file that is organized with 8760 values in each column and a number of columns that correspond to the number of test points. Components to generate this csv from Butterfly CFD results will be coming in later releases. Stay tuned!
As always let us know your comments and suggestions.
Enjoy!Ladybug Analysis Tools Development Team
…
t file** - ply file with just x,y,z locations. I got it from a 3d scanner. Here is how first few lines of file looks like - ply format ascii 1.0 comment VCGLIB generated element vertex 6183 property float x property float y property float z end_header -32.3271 -43.9859 11.5124 -32.0631 -43.983 11.4945 12.9266 -44.4913 28.2031 13.1701 -44.4918 28.2568 13.4138 -44.4892 28.2531 13.6581 -44.4834 28.1941 13.9012 -44.4851 28.2684 ... ... ... In case you need the data - please email me on **nisha.m234@gmail.com**. **Algorithm:** I am trying to find principal curvatures for extracting the ridges and valleys. The steps I am following is: 1. Take a point x 2. Find its k nearest neighbors. I used k from 3 to 20. 3. average the k nearest neighbors => gives (_x, _y, _z) 4. compute covariance matrix 5. Now I take eigen values and eigen vectors of this covariance matrix 6. I get u, v and n here from eigen vectors. u is a vector corresponding to largest eigen value v corresponding to 2nd largest n is 3rd smallest vector corresponding to smallest eigen value 7. Then for transforming the point(x,y,z) I compute matrix T T = [ui ] [u ] [x - _x] [vi ] = [v ] x [y - _y] [ni ] [n ] [z - _z] 8. for each i of the k nearest neighbors:<br> [ n1 ] [u1*u1 u1*v1 v1*v1] [ a ]<br> [ n2 ] = [u2*u2 u2*v2 v2*v2] [ b ] <br> [... ] [ ... ... ... ] [ c ] <br> [ nk ] [uk*uk uk*vk vk*vk]<br> Solve this for a, b and c with least squares 9. this equations will give me a,b,c 10. now I compute eigen values of matrix [a b b a ] 11. This will give me 2 eigen values. one is Kmin and another Kmax. **My Problem:** The output is no where close to finding the correct Ridges and Valleys. I am totally Stuck and frustrated. I am not sure where exactly I am getting it wrong. I think the normal's are not computed correctly. But I am not sure. I am very new to graphics programming and so this maths, normals, shaders go way above my head. Any help will be appreciated. **PLEASE PLEASE HELP!!** **Resources:** I am using Visual Studio 2010 + Eigen Library + ANN Library. **Other Options used** I tried using MeshLab. I used ball pivoting triangles remeshing in MeshLab and then applied the polkadot3d shader. If correctly identifies the ridges and valleys. But I am not able to code it. **My Function:** //the function outputs to ply file void getEigen() { int nPts; // actual number of data points ANNpointArray dataPts; // data points ANNpoint queryPt; // query point ANNidxArray nnIdx;// near neighbor indices ANNdistArray dists; // near neighbor distances ANNkd_tree* kdTree; // search structure //for k = 25 and esp = 2, seems to got few ridges queryPt = annAllocPt(dim); // allocate query point dataPts = annAllocPts(maxPts, dim); // allocate data points nnIdx = new ANNidx[k]; // allocate near neigh indices dists = new ANNdist[k]; // allocate near neighbor dists nPts = 0; // read data points ifstream dataStream; dataStream.open(inputFile, ios::in);// open data file dataIn = &dataStream; ifstream queryStream; queryStream.open("input/query.
pts", ios::in);// open data file queryIn = &queryStream; while (nPts < maxPts && readPt(*dataIn, dataPts[nPts])) nPts++; kdTree = new ANNkd_tree( // build search structure dataPts, // the data points nPts, // number of points dim); // dimension of space while (readPt(*queryIn, queryPt)) // read query points { kdTree->annkSearch( // search queryPt, // query point k, // number of near neighbors nnIdx, // nearest neighbors (returned) dists, // distance (returned) eps); // error bound double x = queryPt[0]; double y = queryPt[1]; double z = queryPt[2]; double _x = 0.0; double _y = 0.0; double _z = 0.0; #pragma region Compute covariance matrix for (int i = 0; i < k; i++) { _x += dataPts[nnIdx[i]][0]; _y += dataPts[nnIdx[i]][1]; _z += dataPts[nnIdx[i]][2]; } _x = _x/k; _y = _y/k; _z = _z/k; double A[3][3] = {0,0,0,0,0,0,0,0,0}; for (int i = 0; i < k; i++) { double X = dataPts[nnIdx[i]][0]; double Y = dataPts[nnIdx[i]][1]; double Z = dataPts[nnIdx[i]][2]; A[0][0] += (X-_x) * (X-_x); A[0][1] += (X-_x) * (Y-_y); A[0][2] += (X-_x) * (Z-_z); A[1][0] += (Y-_y) * (X-_x); A[1][1] += (Y-_y) * (Y-_y); A[1][2] += (Y-_y) * (Z-_z); A[2][0] += (Z-_z) * (X-_x); A[2][1] += (Z-_z) * (Y-_y); A[2][2] += (Z-_z) * (Z-_z); } MatrixXd C(3,3); C <<A[0][0]/k, A[0][1]/k, A[0][2]/k, A[1][0]/k, A[1][1]/k, A[1][2]/k, A[2][0]/k, A[2][1]/k, A[2][2]/k; #pragma endregion EigenSolver<MatrixXd> es(C); MatrixXd Eval = es.eigenvalues().real().asDiagonal(); MatrixXd Evec = es.eigenvectors().real(); MatrixXd u,v,n; double a = Eval.row(0).col(0).value(); double b = Eval.row(1).col(1).value(); double c = Eval.row(2).col(2).value(); #pragma region SET U V N if(a>b && a>c) { u = Evec.row(0); if(b>c) { v = Eval.row(1); n = Eval.row(2);} else { v = Eval.row(2); n = Eval.row(1);} } else if(b>a && b>c) { u = Evec.row(1); if(a>c) { v = Eval.row(0); n = Eval.row(2);} else { v = Eval.row(2); n = Eval.row(0);} } else { u = Eval.row(2); if(a>b) { v = Eval.row(0); n = Eval.row(1);} else { v = Eval.row(1); n = Eval.row(0);} } #pragma endregion MatrixXd O(3,3); O <<u, v, n; MatrixXd UV(k,3); VectorXd N(k,1); for( int i=0; i<k; i++) { double x = dataPts[nnIdx[i]][0];; double y = dataPts[nnIdx[i]][1];; double z = dataPts[nnIdx[i]][2];; MatrixXd X(3,1); X << x-_x, y-_y, z-_z; MatrixXd T = O * X; double ui = T.row(0).col(0).value(); double vi = T.row(1).col(0).value(); double ni = T.row(2).col(0).value(); UV.row(i) << ui * ui, ui * vi, vi * vi; N.row(i) << ni; } Vector3d S = UV.colPivHouseholderQr().solve(N); MatrixXd II(2,2); II << S.row(0).value(), S.row(1).value(), S.row(1).value(), S.row(2).value(); EigenSolver<MatrixXd> es2(II); MatrixXd Eval2 = es2.eigenvalues().real().asDiagonal(); MatrixXd Evec2 = es2.eigenvectors().real(); double kmin, kmax; if(Eval2.row(0).col(0).value() < Eval2.row(1).col(1).value()) { kmin = Eval2.row(0).col(0).value(); kmax = Eval2.row(1).col(1).value(); } else { kmax = Eval2.row(0).col(0).value(); kmin = Eval2.row(1).col(1).value(); } double thresh = 0.0020078; if (kmin < thresh && kmax > thresh ) cout << x << " " << y << " " << z << " " << 255 << " " << 0 << " " << 0 << endl; else cout << x << " " << y << " " << z << " " << 255 << " " << 255 << " " << 255 << endl; } delete [] nnIdx; delete [] dists; delete kdTree; annClose(); } Thanks, NISHA…