Grasshopper

algorithmic modeling for Rhino

Information

Chameleon

CHAMELEON

Chameleon is a plugin for both Grasshopper and Revit with a focus on interoperability, simulation, and efficient practice workflows. Chameleon’s main advantage is its ability to facilitate easy transfer of geometric data between Grasshopper and Autodesk Revit, but also includes other valuable tools to make life easier, both in Grasshopper and Revit.

Website: http://www.hijac-creative.com/chameleon-2/
Location: Washington, DC
Members: 245
Latest Activity: Sep 20, 2023

Discussion Forum

type of chameleon most commonly kept as a pet in captivity

What is the most common type of chameleon found in captivity? Chameleons are popular pet lizards, and many…Continue

Tags: #chameleon, #reptile

Started by Fatima butt Feb 6, 2023.

chameleon is not installing in revit 2016 4 Replies

I have downloaded the chameleon plugin, It has been installed in grasshopper but when I am installing in revit it's not installing, Please help me. How to install in revit?Continue

Started by aman gupta. Last reply by Luigi Olivieri Jun 13, 2019.

New Chameleon Available 29 Replies

Hi all,The new Chameleon (0.4.0.0) is finally here, check it out!http://www.hilojacobs.com/?page_id=464Chameleon now supports editing adaptive…Continue

Started by Hiroshi Jacobs. Last reply by MHMOD DEEP Sep 8, 2017.

running Chameleon in revit

Im facing a problem with the Chameleon while trying to push from GH to Revit, attached below is the error message, any help is higly appreciated.…Continue

Started by MHMOD DEEP Sep 8, 2017.

Comment Wall

Comment

You need to be a member of Chameleon to add comments!

Comment by Nate Holland on October 22, 2012 at 8:33am

Marc,

I've had that issue a few times, usually it happens for one of 2 reasons.  1. You've deleted one of the components in Revit and Chameleon doesn't know how to find the ID. 2. You didn't pass the correct number of points/number params from Grasshopper. Use the Param Viewer to check all of your inputs into the Revit Edit Params component to make sure the count and tree structure is consistent.

Comment by Marc Teer on October 10, 2012 at 5:34pm

Hiroshi-

I'm not having any luck going round trip from acquiring an adaptive component, and then pushing changes to that ac's instance parameters back into revit. When I push new instance parameter values into Revit it throws an error and doesn't change the parameter values.  Your documentation says that this only works for Curtain Panels, so I'm assuming this error is consistent with your plugin's current limitations.  Is that a good assumption?  

Thanks-

Marc

Comment by sun zheng on October 3, 2012 at 5:52am

I cannot install Chameleon on Revit 2012 or 2013. When Revit starts, it says:Failed to initialize the add in Chameleon becase the assembly "Realease\ChameleonRVT.dll" does not exist. I checked the path"C documents and settings\""""""\Roaming\Autodesk\Revit\Addins\2012\Release\ChameleonRVT.dll", it does exist.

Anyone knows why?

Comment by Armando Montejano on October 1, 2012 at 9:33am

Nate,

Thanks for the clarifying, by my side I'll be searching for a solution.

Cheers

Comment by Billie Allen on October 1, 2012 at 9:26am

Nate,

Hiroshi actually performed the analysis on a mass family in a .rvt file (project) while in vasari.  You just need to load your mass family into an .rvt file, and run the analysis.  Hope this helps.

-Bill

Comment by Nate Holland on October 1, 2012 at 9:12am

Armando,

I should clarify my last post. I manually placed the adaptive component into the mass family, by clicking the points. I have yet to find a way to get geometry generated by chameleon into a mass family that will allow me to run Vasari analysis.

Also, Hiroshi,

I tried to transfer a Vasari lofted mass into GH, but found that even on relatively simple lofts with double curved faces, the meshing took too long to transfer effectively. Is there a way to control how many faces the geometry has when its passed from Vasari to GH?

Comment by Armando Montejano on September 30, 2012 at 11:51am

Hello Hiroshi,

Regards to the real projects using using Chameleon as interface between GH - Revit, I'm working on it, in an older post I put some images of a villa (part of a entire spa-hotel in Bacalar, Mexico). As soon as I get something decent to send you count with that.

The other question is regarding to Nate Holland Petition, which I address totally. The capacity to import GH points (adaptive component) in to Mass Family (or any other family) ambient. That wold be an big step to manage GH information in to Revit.

Cheers

P.S. Nate, Could you orient me which is the manual way to put the adaptive family built with Chameleon in to a mass family.

Thanks

Comment by Manuel Huerta on September 30, 2012 at 11:28am

Hello Hiroshi, I installed chameleon both in Revit and GH, but for some reason the Add-ins tab in Revit isn't showing... do you know how can I fix this?

Thanks in advance.

Comment by Nate Holland on September 28, 2012 at 3:05pm

Hiroshi,

After watching the Vasari video you were a part of I decided to try moving geometry from grasshopper to Vasari with Chameleon. I can get geometry into the environment just fine, but I can't run any analysis on it because its an adaptive component not a mass. When I try to place the adaptive components into a mass family, Chameleon tells me that feature can only run in a project window. I found that I can manually place the adaptive component family in the mass family and then run the analysis. So I'm wondering if you could look into that for a future release.

Thank you,

Nate

Comment by Erick Katzenstein on September 10, 2012 at 10:11am

Hiroshi, here's a post we just put up: http://lmnts.lmnarchitects.com/featured/adaptive-components/

We can't say too much about the project yet, but will be posting more in the coming months.  Thanks.

 

Members (245)

 
 
 

About

Translate

Search

Videos

  • Add Videos
  • View All

© 2024   Created by Scott Davidson.   Powered by

Badges  |  Report an Issue  |  Terms of Service