Voronoi with Chamferred Points - Grasshopper2024-03-28T14:15:18Zhttps://www.grasshopper3d.com/forum/topics/voronoi-with-chamferred-points?commentId=2985220%3AComment%3A193617&feed=yes&xn_auth=noDavid and Jon,
Thanks for t…tag:www.grasshopper3d.com,2011-03-20:2985220:Comment:1940172011-03-20T01:36:30.488ZShieldsyhttps://www.grasshopper3d.com/profile/Shieldsy
<p>David and Jon,</p>
<p> </p>
<p>Thanks for the help. I managed to somewhat combine the advice from both of you and came up with something that looks pretty good! </p>
<p> </p>
<p>I have to say though, that I find the various options that go with loft such as build, refit, etc. kinda confusing, but i think the end result is not too bad. </p>
<p> </p>
<p>Thanks again for your help. </p>
<p> </p>
<p>Ben</p>
<p> </p>
<p> </p>
<p>David and Jon,</p>
<p> </p>
<p>Thanks for the help. I managed to somewhat combine the advice from both of you and came up with something that looks pretty good! </p>
<p> </p>
<p>I have to say though, that I find the various options that go with loft such as build, refit, etc. kinda confusing, but i think the end result is not too bad. </p>
<p> </p>
<p>Thanks again for your help. </p>
<p> </p>
<p>Ben</p>
<p> </p>
<p> </p>
You guys are great, thanks…tag:www.grasshopper3d.com,2011-03-20:2985220:Comment:1940142011-03-20T00:23:05.774ZShieldsyhttps://www.grasshopper3d.com/profile/Shieldsy
<p> </p>
<p>You guys are great, thanks a lot!</p>
<p> </p>
<p>I'll see how I go. </p>
<p> </p>
<p>You guys are great, thanks a lot!</p>
<p> </p>
<p>I'll see how I go. </p> Ah yes, the attachment. That'…tag:www.grasshopper3d.com,2011-03-19:2985220:Comment:1938222011-03-19T23:22:51.303ZDavid Ruttenhttps://www.grasshopper3d.com/profile/DavidRutten
<p>Ah yes, the attachment. That's what I get for doing support at 0:30 am...</p>
<p> </p>
<p>--</p>
<p>David Rutten</p>
<p>david@mcneel.com</p>
<p>Poprad, Slovakia</p>
<p>Ah yes, the attachment. That's what I get for doing support at 0:30 am...</p>
<p> </p>
<p>--</p>
<p>David Rutten</p>
<p>david@mcneel.com</p>
<p>Poprad, Slovakia</p> Well, the voronoi cells are o…tag:www.grasshopper3d.com,2011-03-19:2985220:Comment:1940112011-03-19T23:22:07.906ZDavid Ruttenhttps://www.grasshopper3d.com/profile/DavidRutten
<p>Well, the voronoi cells are outputted as polylines. So you can either get the control-points for the polylines (there's a component called 'Control Points' in Curve.Analysis). Once you have these points, use them to create a Control Point curve (probably degree=2).</p>
<p> </p>
<p>The other option is to use the Discontinuity component, which should return a list of all the kinks in a curve. For polylines it's basically the same data, with the exception it won't give you duplicate points at…</p>
<p>Well, the voronoi cells are outputted as polylines. So you can either get the control-points for the polylines (there's a component called 'Control Points' in Curve.Analysis). Once you have these points, use them to create a Control Point curve (probably degree=2).</p>
<p> </p>
<p>The other option is to use the Discontinuity component, which should return a list of all the kinks in a curve. For polylines it's basically the same data, with the exception it won't give you duplicate points at the start/end of the curve.</p>
<p> </p>
<p>I attached an example file.</p>
<p> </p>
<p>If you want really clever fitting like in Jon's example, there's nothing that will directly do that for you (except the component in StructDraw).</p>
<p>--</p>
<p>David Rutten</p>
<p>david@mcneel.com</p>
<p>Poprad, Slovakia</p> Thanks for replying so quickl…tag:www.grasshopper3d.com,2011-03-19:2985220:Comment:1936172011-03-19T22:41:10.863ZShieldsyhttps://www.grasshopper3d.com/profile/Shieldsy
<p>Thanks for replying so quickly David!</p>
<p> </p>
<p>I must admit I am very new to Grasshoppper. I suppose it could be curves with their control points at the Voronoi cell corners but I am not sure how to firstly define points at each of the voronoi cell corners and then to draw the corresponding curve, with the correct proportions. </p>
<p> </p>
<p>Cheers!</p>
<p> </p>
<p> </p>
<p>Thanks for replying so quickly David!</p>
<p> </p>
<p>I must admit I am very new to Grasshoppper. I suppose it could be curves with their control points at the Voronoi cell corners but I am not sure how to firstly define points at each of the voronoi cell corners and then to draw the corresponding curve, with the correct proportions. </p>
<p> </p>
<p>Cheers!</p>
<p> </p>
<p> </p> At least for the patched spl…tag:www.grasshopper3d.com,2011-03-19:2985220:Comment:1938142011-03-19T22:35:09.440ZJon Mirtschinhttps://www.grasshopper3d.com/profile/JonMirtschin
<p><a target="_blank" href="http://www.grasshopper3d.com/photo/cell-fillet/prev?context=user"><img class="align-full" src="http://storage.ning.com/topology/rest/1.0/file/get/2708653941?profile=original"/></a></p>
<p>At least for the patched splines approach that StructDrawRhino uses some of the control points are offset outside the original polygon. I've attached the definintion if it's of interest, it produces cells as shown in the image.</p>
<p> </p>
<p> </p>
<p><a target="_blank" href="http://www.grasshopper3d.com/photo/cell-fillet/prev?context=user"><img class="align-full" src="http://storage.ning.com/topology/rest/1.0/file/get/2708653941?profile=original"/></a></p>
<p>At least for the patched splines approach that StructDrawRhino uses some of the control points are offset outside the original polygon. I've attached the definintion if it's of interest, it produces cells as shown in the image.</p>
<p> </p>
<p> </p> Isn't this just curves with t…tag:www.grasshopper3d.com,2011-03-19:2985220:Comment:1901112011-03-19T15:31:13.451ZDavid Ruttenhttps://www.grasshopper3d.com/profile/DavidRutten
<p>Isn't this just curves with their control points at the voronoi cell corners?</p>
<p> </p>
<p>--</p>
<p>David Rutten</p>
<p>david@mcneel.com</p>
<p>Poprad, Slovakia</p>
<p>Isn't this just curves with their control points at the voronoi cell corners?</p>
<p> </p>
<p>--</p>
<p>David Rutten</p>
<p>david@mcneel.com</p>
<p>Poprad, Slovakia</p>