Grasshopper

algorithmic modeling for Rhino

This video shows the new functionality in Butterfly that allows users to interact with the analysis and load the results of the CFD simulation while the anal...

Views: 768

Comment

You need to be a member of Grasshopper to add comments!

Comment by Shahrokh Kamyab on March 15, 2019 at 6:20am

Hello!
About butterfly 0005:
I downloaded blueCFD, BF 0005 . and everything seems to work, but simulation just takes unimaginable time . I run the outdoor_airflow (everything default) and the description in the solution part says "Solution should be converged in 561 iterations with default settinbgs" after 10 minutes it's on iteration 8.
Is it normal? 

Best regards
Shahrokh

Comment by Soo Jeong Jo on October 29, 2017 at 4:00pm

Thank you so much for the release of Butterfly! It sounds too early since it is just released, but I am wondering if there are any validation case studies by using Butterfly. I saw case studies for OpenFOAM, but couldn't find one for Butterfly. 

Comment by Mostapha Sadeghipour Roudsari on October 26, 2017 at 9:21am

@Anupama, I replied to the discussion. You should send your questions either to GitHub or the discourse.ladybug.tools

Comment by Anupama on October 26, 2017 at 2:33am

Hi

I am running the “Outdoor airflow” example file. I am trying to map pressure on walls and roof of the bigger block. Front, back and one of the side wall gives positive pressure results however roof, and another side wall gives result of <-100000000000000000000000000….Pascal

Is this trying to say pressure is negative on these sides.If yes, is there a way to map negative pressure on those meshes?

please visit the following url:

http://www.grasshopper3d.com/forum/topics/pressure-values-too-low

Thank you and Best Regards

Anupama

Comment by Rajeev Jain on October 12, 2017 at 3:15am
I din't install the docker, but installed http://www.openfoam.com/download/install-windows-10.php
on Ubuntu bash, will this work?
Comment by Yuqing Pan on August 5, 2017 at 2:09am

Hi,

I ran the example file "01_0_outdoor_airflow.gh" but got different results. Do you know why?

please visit the following url:

http://www.grasshopper3d.com/forum/topics/wind-speed-is-too-low-whe...

Besh wishes,

Yuqing

Comment by Mostapha Sadeghipour Roudsari on May 13, 2017 at 8:40am

Hi Robert, Based my understanding you only need to allow Hardware Assisted Virtualization. Haven't heard about the second one. This one need to be set always to true to be able to run the VM and use docker which is how butterfly accesses and runs OpenFOAM.

Thanks for the note. The links are fixed. They also come with the installation. In case you haven't seen them already I made a number of videos for installation and getting started with Butterfly.

Comment by Robert Narracci on May 8, 2017 at 12:03pm

Mostapha,

P.S. on your "Getting Started" GitHub page the example link in 3.1.1 and 3.1.2 are broken.

Comment by Robert Narracci on May 8, 2017 at 11:54am

Hi Mostapha,

The OpenFOAM installations requires one to first change the BIOS to allow Hardware Assisted Virtualization. I enabled the two places I found this on my laptop; one was simply labeled Virtualization Technology; the other was labeled Virtualization Technology Directed (VT-d). Do you know if enabling both of these is neccesary? Do you know if this must be set permanently or is it just for the installation of OpenFOAM?

My Best,

Rob

Comment by architsama on October 7, 2016 at 2:59am

i have follow this post, but OpenFOAM don`t work ether.

About

Translate

Search

Photos

  • Add Photos
  • View All

Videos

  • Add Videos
  • View All

© 2024   Created by Scott Davidson.   Powered by

Badges  |  Report an Issue  |  Terms of Service