Panelling with non square based components

Replies to This Discussion

Permalink Reply by Giulio Piacentino on May 14, 2010 at 12:18pm

Hi Marysol,

one method that might work could be the following:
write or find a definition that constructs a subdivision of a surface with full loops. Any definition with meshes or full diagrids like here will work:
- http://www.grasshopper3d.com/forum/topics/diagonal-grid-without-1
or see a lot of beautiful methods here to get inspiration:
- http://www.livearchitecture.net/archives/4883
Then, you could construct twisted boxes based on these curves and use them as targets? Could this be a way forward?

- Giulio

• ▶ Reply

Permalink Reply by Jacek Jaskólski on May 14, 2010 at 12:52pm

Hi Marysol, hi Giulio,

This question made me curious because it seems there're different possible approaches to defining the rythm of those dumplings...for example:

a diagrid pattern:

or a brick pattern:

Maybe you could try both...

Here's the definition for the second one:

(the coffee stained part is where the shifting happens)

Attachments:

• SrfBrickPattern.ghx, 179 KB

• ▶ Reply

Permalink Reply by Giulio Piacentino on May 14, 2010 at 1:21pm

Nice!

• ▶ Reply

Permalink Reply by Andrea Graziano on December 20, 2010 at 2:43am

looking at the above image i set a def called "Uneven subdivision" of a NURBS surface, controlled by random intervals.

you can find it at:

http://www.co-de-it.com/wordpress/code/grasshopper-code

 

• ▶ Reply

Permalink Reply by marysol kraviez on December 20, 2010 at 4:26pm

looks great! i will try it as soon as i can! thanks!!

• ▶ Reply

Permalink Reply by marysol kraviez on May 14, 2010 at 1:29pm

Thanks to both!!!
Yeah, i had a version of a diagrid but i could' n t link it to my definition, i will definitely try with this others..and the brick one seems to be exactly what i wanted since it is how i built it in maya...
i will try both tomorrow as soon as i can
THANKS!

• ▶ Reply

Permalink Reply by marysol kraviez on May 14, 2010 at 1:41pm

Oh, and just another question ,
What about if i also wanted these non square components to intersect each other ? again, i' m posting 2 screenshots with what i did in maya and what i did with the same definition that i have posted before in GH. Giulio,I have seen your beautiful definition for chains but i don' t know how to "chain" my own components.
thanks!!!
m

Attachments:

• encastre.obj, 27 KB
• what i want.jpg, 275 KB
• what i got.jpg, 252 KB

• ▶ Reply

Permalink Reply by P. Casey Mahon on May 14, 2010 at 1:51pm

marysol,
I don't know how Giulio went about the chain's, but a strategy that may work is to make your components go outside of their "boxes" so that your tile becomes pieces of neighbors that put together make the whole instead of trying to get the whole to intersect...I hope that makes sense if not let me know and I'll try to put a sketch together that explains it a little better

• ▶ Reply

Permalink Reply by marysol kraviez on May 14, 2010 at 2:02pm

Hi P.,
yeah, that is what i have done with my previous attempt, i didn' t try it with this component yet because i was wondering if there was a precise way to do it .Otherwise, i will have to modify my component to do it.But it would be nice to find a definition that can link a component without the box .Or an editable box so we could adjust it to our geometry.
or to be able to intersect the boxes...or???
Thanks
m

• ▶ Reply

Permalink Reply by P. Casey Mahon on May 14, 2010 at 2:16pm

those things would be great for sure, but are limited by the way that the box morphing works...it is possible to build all of your geometry from the uv grid of points on the surface instead of relying on a component to be morphed into twisted boxes on the surface, however it is much more difficult than what you are currently doing, but not impossible.

Check out this tutorial to see an example of the kind of component creation that I'm talking about:

http://www.tedngai.net/experiments/gh-powercopy.html

• ▶ Reply

Permalink Reply by Jacek Jaskólski on May 15, 2010 at 10:27am

Marysol,

I tried another approach and here's what I've come up with:

The definition follows the logic of the box morph method, only the iso-trim portions of the surface are overlapping each other:

I've attached the ghx, tell me whether it works for you or not.

--
The drawback of paneling methods like this one is that the geometry gets deformed on curved surfaces (not mentioning uneven uv distribution), so they're useless if you're planning to fabricate the design using identical pieces...
If that's the case I think you should consider using a physical solver of some kind.
--

Just a guess - is this a jewelry design?

Attachments:

• chain_mail.ghx, 569 KB

• ▶ Reply

Permalink Reply by marysol kraviez on May 15, 2010 at 6:22pm

Hi J,
I am trying your definition( nicel! )and trying to understand it logics..but i guess i' ll need more practice! It does work pretty well for the effect i want to achieve ( specially when i subdivided it in maya and it gets really smooth) but i don' t know why, i only get half of the surface populated and without reaching the edges as well ( as the screenshot i'm posting now). and the definition shows that's something is wrong . I' ve tried to move all the sliders but only the one for the scale works.
How did you do to get the image you have posted? How do you do to get the whole chosen surface populated?
I' ve tried several surfaces but with the same result.
thanks
m

Attachments:

• half chain.jpg, 324 KB

• ▶ Reply

• ‹ Previous
• 1
• 2
• Next ›
• Page