Grasshopper 0.7.0014 available for download

Replies to This Discussion

Permalink Reply by CarloMaria Ciampoli on May 16, 2010 at 2:48pm

thanks David!

• ▶ Reply

Permalink Reply by Daniel Piker on May 16, 2010 at 3:57pm

Thanks David! Awesome stuff

• ▶ Reply

Permalink Reply by raf2205 on May 16, 2010 at 4:04pm

Hi David,
I opened a definition wrote in GH 0.6.0059 in this new release 0.7.0014 you just posted and had the following warning message.
Can you please light me on this ?

thanks

raf

Attachments:

• errors.png, 8 KB

• ▶ Reply

Permalink Reply by David Rutten on May 17, 2010 at 1:09am

Hi raf,

can you send me the file?

--
David Rutten
david@mcneel.com
London, UK

• ▶ Reply

Permalink Reply by Tuan N. Tran on May 16, 2010 at 5:34pm

David,

Great release with Galapagos! Can you please post the catenary examples you showed at the AA recently? Thanks.

• ▶ Reply

Permalink Reply by David Rutten on May 17, 2010 at 1:10am

Attached.

--
David Rutten
david@mcneel.com
London, UK

Attachments:

• GalapagosExamples.zip, 176 KB

• ▶ Reply

Permalink Reply by Tuan N. Tran on May 16, 2010 at 11:46pm

Hi David

I set up Galapagos to solve for the minimum bounding box. It worked great for the generic test case of a rotated box! Thanks again for the release. However, there's some strangeness going on with the bounding box.

On the left is the original with a GH bounding box. The middle is the bottom half (rhino BooleanSplit) with a GH bbox. The right is bottom half with a rhino bbox. As you can see, the middle and the right bboxes are not the same.

• ▶ Reply

Permalink Reply by David Rutten on May 17, 2010 at 1:12am

Yes I see. I think RhinoCommon too often uses the quick'n'dirty BoundingBox (which operates only on the control-points of geometry) rather than the "tight" BoundingBox which takes trims into account.

I'll see about getting it fixed.

--
David Rutten
david@mcneel.com
London, UK

• ▶ Reply

Permalink Reply by quitronic on May 16, 2010 at 11:58pm

thanks David!
Galapagos!!!

• ▶ Reply

Permalink Reply by robert cervellione on May 17, 2010 at 6:47am

any chance of getting a build for rhino 5 64 bit.

• ▶ Reply

Permalink Reply by Thorsten Strathaus on May 17, 2010 at 8:48am

Hi David,

any chance of finding examples/explanations for the use of galapagos somewhere?

Thanks,

Thorsten

• ▶ Reply

Permalink Reply by Thorsten Strathaus on May 17, 2010 at 9:25am

If I get the chance to respond to myself:

http://www.youtube.com/watch?v=NFOodjZUVhU
as explanation video,

and to shorten your "I try to connect everything to find out what works" period:

Connect some sliders to the Genome-part of Galapagos,
and a number containing parameter to the Fitness-part.

then you should be able to run a calculation test.
In my case, I get some error messages, but the calculation does run.

Thorsten

Attachments:

• galapagos start.png, 145 KB
• errors.jpg, 293 KB

• ▶ Reply

• ‹ Previous
• 1
• 2
• 3
• …
• 6
• Next ›
• Page