Grasshopper

algorithmic modeling for Rhino

Hi 

I'm new in GH and I'm trying to reduce the differentiation of panels of my freeform surface. I want to equalize length of panels edges to make the manufacturing cheaper.

I tried to obtain this effect using Kangaroo's spring, I achieved equalized panels, but the whole surface has been distorted. ---> 

 

Now I try to reduce the quantity of different panel shapes to minimum (could be 5 up to 20), whereas the original smooth form of my structure and  her borders should remain fixed. 

I found few methods in the following articles:

http://www.gasathj.com/tiki-read_article.php?articleId=31 
http://sechel.de/publications/AAG2014Periodic.pdf

Unfortunately I can't obtain similar effect like in articles above,

can anybody make out with it?

Thank You for your help!

Views: 1909

Attachments:

Reply to This

Replies to This Discussion

I'm sure there are those here who could get GH to do what you want. However, there is another tool you might check out: EvoluteTools for Rhino.

However, looking at your surface, I'm not sure you can get equal size panels if you want the divide the surface the way you have. Your surface converges at the top, so if you are using the same number of divisions at the bottom and top, you can't have the same size panel. How did you create the design surface? A lot of panelization problems can be improved or solved by changing the geometry rather than dealing just with the panelization.

One alternative would be to create a panelization that falls over the edge, then trim the panels along the edges.

I agree with your suggestion that in my constrictive surface I can't use the same number of divisions at each size, when I want to achieve panel equalization. I did it at first because UV division of surface is the only one method that I know. So in conclusion I'm looking for another method of dividing, analogous like described in following article: http://www.gasathj.com/tiki-read_article.php?articleId=31, or http://sechel.de/publications/AAG2014Periodic.pdf  but unfortunately I can't read out the GH script scheme because of low resolution. There are some directions how to do it but my GH crafts are too poor to reproduce described reasoning. In passing not each panel must be equal but the aim to achieve surface consiting of  few different panels. Could be approximately  from 5 up to 20 different panel shapes.

You can find the scheme of my surface in " panel edge length optimization.gh" file enclosed in the message above. This surface is a part of whole building shape which looks like this:

 

Thanks for your advice!

I didn't realize you are using ruled surfaces. Here's an idea that gives you equal sized panels. Granted, it changes the aesthetics.

What I did was took the bottom curve, copied it up the twisting form without scaling (I could have gone back to your copied triangles before you scaled). By creating a loft from this non-scaled form, I can panelize it knowing the triangles are equal. Then I trimmed it to the boundary of the form you want. All the internal panels are equal. All the edge panels are unique, although because the way you created form, the are mirrored.

172 equal panels in the middle, 39 pairs of unique panels along the edges. Not in the 5-20 range, yet, but another idea.

It seems to be good idea but I have a problem with rebuilding your GH script. When I try to use my origin triangles sth doesn't work. What's more when my triangles aren't scaled, their edges are in different place than in scaled one. And one question- is that surface, which you made, rulled or is it planar? 

I did sth like in file enclosed under but it doesn't work. Maybe I don't understand your idea in 100%.

In passing are You able to crack this reasoning? (from 1sth article):

I'm very grateful to You for your help!

Attachments:

Hello Maciej, did you manage to solve this issue? I am looking for the same sollution, I dont need identical panels but I need to reduce the amount.

RSS

Translate

Search Grasshopper

Photos

  • Add Photos
  • View All

© 2017   Created by Scott Davidson.   Powered by

Badges  |  Report an Issue  |  Terms of Service